Golden Lighting 1567-1W PC User Manual

Wire

P3

Deco Nut

5/32"xH9mm

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

PARTS & ASSEMBLY SHEET

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

Read and review installation instruction sheet before

Fig. 4

J

H

I

L

K

Fixture Name: Riverton 1567-1W PC

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing

or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap
1 ea
Ø4"*1.5mm

Connnector
3 ea

Green Ground
Screw
1 ea
#8-32N*H10mm

Part Needed Quantity
Part Needed Quantity

IXTURE ASSEMBLY INSTRUCTIONS

F

assembling the fixture.

Junction Box Screw
2 ea
#8-32N*H32mm

Hex Nut
2 ea
5/32"*H3.5mm

Mounting
Screw
2 ea
5/32"*H38mm

(Round)
2 ea

1567-1W PC

1. Place the fixture Back Plate ( K ), over the Mounting
Screws (B), so it protrude through the hole in the
Back Plate ( K ).

2. Thread the Deco Nuts ( J ) onto the Mounting Screws (B)
and continue turning until the Back Plate (K) is snug against
the wall .

3. Slide the Glass Shade ( H ) over Socket (I) and secure
Glass Shade (H) by threading the Socket Ring (J)
to Socket (I).

4. Install light bulb in accordance with the fixture's
specifications .

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

THE FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

1567-1WPartsInstallation_20120313mRe.xls

INSTALLATION INSTRUCTIONS

Fig. 2

parts are included as shown in the illustration and parts list.

Screws(B) half way into the Mounting Strap(A).

required by fixture type.

FIXTURE WIRES

HOUSE WIRES

HOUSE WIRES

WHITE

BLACK

RIBBED (WHITE)

SMOOTH (BLACK)

FIXTURE WIRES

J

H

I

L

K

Fixture Name: Riverton 1567-1W PC

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE(Fig.1)

1.Carefully remove the new fixture from the carton and the
yellow bag that holes all your parts. Check that all

2. Shut off power at the circuit breaker and remove the old
fixture from wall, including the old mounting strap.

3.The Mounting Strap(A) contains several pairs of threaded
holes, find the pair of holes that match the holes spacing
in your fixture Back Plate (K) and thread the two Mounting

4.Place the Mounting Strap (A) over the Junction Box (E) so
the Mounting Screws (B) are vertical or horizontal, as

5. Attach the Mounting Strap (A) to the Junction Box (E) by
using the two mounting screws(D). Tighten the screws
securely.

CONNECTING THE WIRES (Fig. 2)

6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).

7. Attached the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the
green Ground Screw on the Mounting Strap (B) or
connect both wires together using the correct size
of wire connectors
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.

8. Tuck these wire connections neatly into the Junction Box.

Fig. 1

FINISHING THE INSTALLATION (Fig. 3)

9. Place the fixture Back Plate (J) over the Thread Rod (B),
so it protrude through the hole in the Back Plate (J)

10. Thread the Deco Nut (H) onto the Thread Rod (B) and
continue turning until the Back Plate (J) is snug against
the wall.

11. Install glass as per the fixture assembly instructions

12. Slide the Glass Shade ( H ) over Socket (I)
and secure Glass Shade (H) with Socket Ring(J)

13. Install light bulb in accordance with the fixture's
specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)

Fig. 3

For Customer Service, contact the place of purchase to arrange for replacement parts.