Page 1
PARTS & ASSEMBLY SHEET
Company Name:_______________________Co. Account #:____________
F
Read and review installation instruction sheet
before assembling the fixture.
Fig 1
Fixture Name: Sancerre 1425-M1L WG
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any pa rts
are missing or damaged, please note onthis sheet and contact the place of purchase to arran ge for
replacement parts.
PARTS LIST
Canopy Mounting Screws Top loop
1ea ∅5-1/2"*H1-1/8" 2ea 8#32-IP*1" 1ea 1/8-IP*H2-1/2"
Chain Wire connectors Nipple
1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H55mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/4"*H42mm 1ea W4-1/8"*E1"*H5mm
Glass Shade Bulb
1ea ∅2"*3"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
to be filled out by retailer
Canopy loop
with Collar
1ea
Mounting strap
IXTURE ASSEMBLY INSTRUCTIONS
1. Unwrap Crystal Chain (Q) from the packaging.
2. Install Bulb (O), Glass shade (P) to Socket (N).
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
1425-M1L WG
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
3. By measuring, determine correct num ber of links
Nipple (C) and pull until taut.
* You may now install the fixture.
Fig 2
PARTS & ASSEMBLY SHEET
Fixture Name: Sancerre 1425-M1L WG
needed for proper hanging height. To remove any
excess chain, use a pair of pliers to open one link of
Chain (K) and discard the excess chain.
4. Use one Chain Connector (L) to att ac h one end of
the chain to Top Loop (J). Then close the chain
connector.
5. Feed the fixture wires through the chain (every three
links) and pull the wires unt i l taut.
6. Slip Canopy Loop Collar (H) over the chain, then do
the same with the Canopy (G).
7. When ready to complete the installation, use the
other chain connector and attach the other end of the
chain to the Canopy Loop (H). Then close the chain
connector.
8. Feed the fixture wires through Canopy Loop (F) and
Page 3
CONNECTING THE WIRES (Fig 2)
BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by t ightening Canopy Loop
collar (H) into Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture assembly sheet.
INSTALLATION INSTRUCTIONS
7. Unscrew Canopy Loop Collar (H) from Canopy Loop (F). Take Canopy
reached. *Canopy Loop Collar (H) should fit snugly on Canopy Loop (F) after
Canopy (G) is installed. Remove Canopy (G) and Canopy Lock Collar (H).
weight of the fixture while you complete the wiring connections.
Canopy Loop (F) and Nipple (C) and into the outlet box.
Fig. 1
HANGING THE FIXTURE (Fig.1)
through Mounting Strap (D). Thread Hex N uts (A) onto Nipple (C) until tight.
using Mounting screws (E). Tighten the screws securely with a screw driver.
Fixture Name:
Sancerre 1425-5/9/3P/M1L WG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixtur e from the carton and the yellow bag that
holds all parts. Check that all parts are included as shown in the Part s and
Assembly Sheet.
2. Shut off the power at the circuit breaker and remove t he old fixture from
ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C), with Canopy Loop (F) attached, into
Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which should protrude
6. Take this mounting str ap as s embly and mount it to the ceiling junction box
For Chandelier Light Fixture
(G) and pass over Canopy Loop (F). Approximately one half of the canopy
loop exterior threads should be exposed. A dj us t until the desired height is
8. Assemble the fixture. Use an assistant or a secure support t o hold the
9.Thread the fixture wires and gr ound wire of the assembled fixture through
10. Attach the power supply wires to the fixture lead w ires by connecting BLACK to
11. Attach the GROUND wire (GREEN or COPPER) from the Junction Box and the
fixture Ground Wire to the green Ground Screw on Mounting Bracket ( D) or c onnect
both wires together using the correct size of wire connectors.
NOTE: Twist the wires toget her in the s ame direction you twist the w ire connec t or
onto the wires.
YOUR INSTALLATION IS NOW
COMPLETE. RETURN POWER TO
THE JUNCTION BOX AND TEST THE
For Customer Service, contact the place of purchase to arrange for replacement parts.
FIXTURE.
Loading...