Page 1
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: _ ____ ___
Read and review installation instruction sheet, but do not
ASSEMBLING THE FIXTURE (Fig.1)
Connection Pin (U) sits on top of Arm (S). This will ensure
Fig 1
Fixture Name: Sancerre 1425-BA3 W G
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact th e place of purchase t o arrange for
replacement parts.
PARTS LIST
Mounting Strap Mounting Screws Deco Nut
1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 8#32-IP*H9mm
Wire connectors Mounting Screws Hex Nut
3ea P3 Orange 2ea 8#32-IP*1" 2ea 8#32-IP*H3mm
Socket Tool
1ea 1-1/8"*3-5/8"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
FIXTURE ASSEMBLY INSTRUCTIONS
install before assembling the fixture.
1. Crystal Chains (T) are individually wrapped and must
be hung piece by piece. Remove Crystal Chain (T) from
the packaging and examine the chain for Connection Pin
(U). Drape Crystal Chain (T) over Arm (S) so that
proper draping length.
2. Install outer, Clear Glass (S) and inner, Opal Glass (R)
by sliding both pieces of glass over Socket (T). Place
Gasket (Q) inside Opal Glass (R) and over Socket (T).
Secure glass in place by tightening Socket Ring (P) over
Socket (T), using Socket Tool (X).
Note: To avoid broken glass, do not over tighten Socket
Ring (P).
1425-BA3 WG
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
Fig. 1
Fig. 2
5. Attach Mounting Strap (F) to the Junction Box using the two mounting
screws (H) and tighten securel y with screw driver.
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig.1)
illustrations and the Parts and Assembly Sheet.
including the old mounting strap.
3. Mounting Strap (F) contains several pairs of threaded holes. Find the pair of
holes that matches the holes spaci ng in your fixture Back Plate (H) and thread
the two Mounting Screws (D) half way into Mounting Strap (F) and secure with
Hex Nut (G).
(D) are vertical or horizontal, as requir ed by fixture type.
CONNECTING THE WIRES (Fig 2)
BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire (GREEN or COPPER) from t he Junction Box and
the fixture Ground w ire to the green Ground Screw (I) on Mounting Bracket (F)
or connect both wires together using the correct size of wire connect ors. -
connector (L) onto the wir es.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION(Fig.3)
Mounting Screws (D) until tight as shown on Fig.1.
10. Install the light bulbs and glass shade as per the fixture assembly sheet.
Fig. 3
Fixture Name: Sancerre 1425-BA3 WG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the carton and the yel low bag that
holds all your parts. Check that all parts are included as shown in the
2. Shut off power at the circuit breaker and remove the old fixture from wall,
4. Place Mounting Strap (F) over Junction Box (A) so that Mounting Screws
For Wall Mount Light Fixture
6. Attach the power supply wires to the fixture lead wires by connecti ng
NOTE:Twist the wires t ogether in the same direction you twist the wire
9. After tucking these wire connections neatly into t he Junction Box and
placing the fixtur e B ack Plate (E) over the two Mounting Screws (D), secure
Back Plate (E) against the wall by threading two Deco Nuts (O) over the two
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE
JUNCTION BOX AND TEST THE FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...