Golden Lighting 1425-BA1 WG User Manual

Page 1
Read and review installation instruction sheet, but do not
ASSEMBLING THE FIXTURE (Fig.1)
1. Crystal Chains (T) are individually wrapped and must be
Fig 1
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: _ ____ ___
Fixture Name: Sancerre 1425-BA1 W G
Notice:
missing or damaged, please note onthis sheet and contact th e place of purchase t o arrange for replacement parts.
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
PARTS LIST
Mounting Strap Mounting Screws Deco Nut
1ea ∅4"*H2mm 2ea 8#32-IP*1" 2ea 8#32-IP*H9mm
Wire connectors Mounting Screws Hex Nut
3ea P3 Orange 2ea 8#32-IP*1-1/2" 2ea 8#32-IP*H3mm
Socket Tool
1ea 1-1/8"*3-5/8"
Part Needed Quantity Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish) Comments
FIXTURE ASSEMBLY INSTRUCTIONS
install before assembling the fixture.
hung piece by piece. Remove Crystal Chain (T) from the packaging and examine the chain for Connection Pin (U). Drape Crystal Chain (T) over Arm (S) so that Connection Pin (U) sits on top of Arm (S). This will ensure proper draping length.
2. Install outer, Clear Glass (S) and inner, Opal Glass (R) by sliding both pieces of glass over Socket (T). Place Gasket (Q) inside Opal Glass (R) and over Socket (T). Secure glass in place by tightening Socket Ring (P) over Socket (T)using Socket Tool (X). Note: To avoid broken glass, do not over tighten Socket Ring (P).
NOTE: INSTALL THE GLASS ASSEMBLY AFTER THE
FIXTURE IS HUNG.
1425-BA1 WG
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yel low bag that
illustrations and the Parts and Assembly Sheet.
wall, including the old mounting strap.
and secure with Hex Nut ( G ).
Screws (D) are vertical or horizontal, as requi red by fixtur e type.
CONNECTING THE WIRES (Fig 2)
BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire (GREEN or COPPER) from the Junction Box
connector (L) onto the wir es.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION(Fig.3)
over the two Mounting Screws (D ) until tight as shown on Fig.1.
sheet.
JUNCTION BOX AND TEST THE FIXTURE.
Fig. 3
Fig. 1
Fig. 2
5. Attach Mounting Strap (F) to the Junction Box using the two mounting screws (H) and tighten securel y with screw driver.
Fixture Name: Sancerre 1425-BA1 WG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
holds all your parts. Check that all parts are included as shown in the
2. Shut off power at the circuit breaker and remove the old fixture from
3. Mounting Strap (F) contains several pairs of threaded holes. Find the pair of holes that matches t he holes spacing in your fixture Back Plate (H) and thread the two Mounting Screw s (D) half way into Mounting Strap (F)
4. Place Mounting Strap (F) over Junction Box (A) so that Mounting
For Wall Mount Light Fixture
6. Attach the power supply wires to the fixture lead wires by connecti ng
and the fixture Ground w ire to the green Ground Screw (I) on Mounting Bracket (F) or connect both wi res together using the correct size of wire connectors. - NOTE:Twist the wires t ogether in the same direction you twist the wire
9. After tucking these wire connections neatly into t he Junction Box and placing the fixtur e B ack Plate (E) over the two Mounting Screws (D), secure Back Plate (E) against t he w all by threading two Deco Nuts (O)
10. Install the light bulbs and glass shade as per the fixture assembly
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER TO THE
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...