Page 1
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing
Company Name:_______________________Co. Account #:_____________
ASSEMBLING THE FIXTURE (Fig.1)
Fig 1
Fixture Name: Sancerre 1425-5 WG
Notice:
or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy
1ea ∅5-1/2"*H1-1/8" 2ea 8#32-IP*1" 1ea 1/8-IP*H3-1/4"
Chain Wire connectors Nipple
1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H55mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/4"*H42mm 1ea W4-1/8"*E1"*H5mm
Iron Tube crystal bobeche
5ea ∅1"*4-3/8"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
to be filled out by retailer
Mounting Screws Top loop
Canopy loop
with Collar
5ea ∅1-1/8"*H15mm
Mounting strap
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Feed the fixture wires through the Top loop (J) and pull
the wires until taut.
2. Then screw Top Loop (J) to the threaded center column
of Nipple (M) until tight.
NOTE: INSTALL THE GLASS ASSEMBLY AFTER THE
FIXTURE IS HUNG.
1425-5 WG
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
3. Feed the fixture wires through Top loop (J) and pull the wires
until taut. Then screw Top Loop（J） to the threaded center
5. Use one Chain Connector (L) to attach one end of the chain to
(C) and pull until taut.
Fig 2
ASSEMBLING THE FIXTURE (Fig.3)
slide Candle Sleeve (O) into the hole and straighten.
finish of the candle sleeve.
Fig 3
PARTS & ASSEMBLY SHEET
Fixture Name: Sancerre 1425-5 WG
column of Frame (M) until tight. .
4. By measuring, determine correct number of links needed for
proper hanging height. To remove any excess chain, use a pair
of pliers to open one link of Chain (K) and discard the excess
chain.
Top Loop (J). Then close the chain connector.
6. Feed the fixture wires through the chain (every three links)
and pull the wires until taut.
7. Slip Canopy Loop Collar (H) over the chain, then do the same
with the Canopy (G).
8. When ready to complete the installation, use the other chain
connector and attach the other end of the chain to the Canopy
Loop (H). Then close the chain connector.
9. Feed the fixture wires through Canopy Loop (F) and Nipple
* You may now install the fixture.
1. Crystal Chains (S) are individually wrapped and must be hung
piece by piece. Remove Crystal Chain (S) from the packaging
and examine the chain for Connection Pin (T). Drape Crystal
Chain (S) over Arm (R) so that Connection Pin (T) sits on top of
Arm (R). This will ensure proper draping length.
2. Attach Crystal Bobeche (P) by sliding it over the socket. Then,
Note: Please do not attempt to slide Crystal Bobeche (P) over
the chrome Candle Sleeve (O) as it will scratch and damage the
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by t ightening Canopy Loop
collar (H) into Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture assembly sheet.
INSTALLATION INSTRUCTIONS
HANGING THE FIXTURE (Fig.1)
through Mounting Strap (D). Thread Hex N uts (A) onto Nipple (C) until tight.
using Mounting screws (E). Tighten the screws securely with a scr ew driver.
Fig. 1
7. Unscrew Canopy Loop Collar (H) from Canopy Loop (F). Take Canopy
reached. *Canopy Loop Collar (H) should fit snugly on Canopy Loop (F) after
Canopy (G) is installed. Remove Canopy (G) and Canopy Lock Collar (H).
weight of the fixture while you complete the wiring connections.
Canopy Loop (F) and Nipple (C) and into the outlet box.
CONNECTING THE WIRES (Fig 2)
BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fixture Name: Sancerre 1425-5/9/3P/M1L WG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixtur e from the carton and the yellow bag that
holds all parts. Check that all parts are included as shown in the Part s and
Assembly Sheet.
2. Shut off the power at the circuit breaker and remove t he ol d fixture from
ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C), with Canopy Loop (F) attached, into
Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which should protrude
6. Take this mounting str ap as s embly and mount it to the ceiling junction box
For Chandelier Light Fixture
(G) and pass over Canopy Loop (F). Approximately one half of the canopy
loop exterior threads should be exposed. A dj us t until the desired height is
8. Assemble the fixture. Use an assistant or a secure support t o hol d the
9.Thread the fixture wires and gr ound wire of the assembled fixture t hr ough
10. Attach the power supply wires to the fixture lead wires by connecting BLACK to
11. Attach the GROUND wire (GREEN or COPPER) from the Junction Box and the
fixture Ground Wire to the green Ground Screw on Mounting Bracket ( D) or c onnect
both wires together using the correct size of wire connectors.
NOTE: Twist the wires toget her in the s ame direction you twist the wire connect or
onto the wires.
YOUR INSTALLATION IS NOW
COMPLETE. RETURN POWER TO
THE JUNCTION BOX AND TEST THE
For Customer Service, contact the place of purchase to arrange for replacement parts.
FIXTURE.
Loading...