Page 1
Company Name:_______________________Co. Account #:_____________
PARTS & ASSEMBLY SHEET
F
Read and review installation instructi on sheet before
assembling the fixture.
ASSEMBLING THE FIXTURE (Fig.1)
tighten onto Nipple (S).
Fig 1
Fixture Name: Sancerre 1425-3P WG
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.
PARTS LIST
Canopy Mounting Screws Top loop
1ea ∅5-1/2"*H1-1/8" 2ea 8#32-IP*1" 1ea 1/8-IP*H3-1/4"
Chain Wire connectors Nipple
1ea 6ft ∅3.8 3ea P3 Orange 1ea 1/4-IP*H55mm
Chain connector
2ea ∅5.8*H61mm 1ea ∅1-1/4"*H42mm 1ea W4-1/8"*E1"*H5mm
Iron Tube crystal bobeche
5ea ∅1"*3-3/8"
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, b r oken glass, bent, b ad finish)
Comments
to be filled out by retailer
Canopy loop
with Collar
5ea ∅3-3/8"*H15mm
Mounting strap
IXTURE ASSEMBLY INSTRUCTIONS
1425-3P WG
1. Straighten the wires and pass them through Nipple
(S), Spacer (R), Square Tube (Q), Spacer (P), Center
Rod Column (O). Push Center Rod Column (O) down
over Spacer (P), through the center of the frame, and
over Spacer (R). Twist Center Rod Column (O) to
2. Pass Spacer (N) over Nipple (M) and screw on Top
Loop (J) until tight.
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
3. Feed the fixture wires through Top loop (J) and pull the
Nipple (C) and pull until taut.
Fig 2
1. Attach Crystal Bobeche (U) by sliding it over the
and straighten.
Fig 3
PARTS & ASSEMBLY SHEET
Fixture Name: Sancerre 1425-3P WG
wires until taut. Then screw Top Loop（J） to the threaded
center column of Frame ( M) unt il tight . .
4. By measuring, determine correct number of links needed
for proper hanging height. To remove any excess chain, use
a pair of pliers to open one link of Chain (K) and discard the
excess chain.
5. Use one Chain Connector (L) to attach one end of the
chain to Top Loop (J). Then close the chain connector.
6. Feed the fixture wires through the chain (every three links)
and pull the wires until taut.
7. Slip Canopy Loop Collar (H) over the chain, then do the
same with the Canopy (G).
8. When ready to com plet e t he inst allation, use t he other
chain connector and attach the other end of the c hain to the
Canopy Loop (H). Then close the chain connector.
9. Feed the fixture wires through Canopy Loop (F) and
* You may now install the fixture.
socket. Then, slide Candle Sleeve (O) into the hole
Note: Please do not attempt to slide Crystal Bobeche
(P) over the chrome Candle Sleeve (O) as it will
scratch and damage the finish of the candle sleeve.
Page 3
INSTALLATION INSTRUCTIONS
7. Unscrew Canopy Loop Collar (H) from Canopy Loop (F). Take Canopy
reached. *Canopy Loop Collar (H) should fit snugly on Canopy Loop (F) after
Canopy (G) is installed. Remove Canopy (G) and Canopy Lock Collar (H).
weight of the fixture while you complete the wiring connections.
Canopy Loop (F) and Nipple (C) and into the outlet box.
Fig. 1
HANGING THE FIXTURE (Fig.1)
through Mounting Strap (D). Thread Hex N uts (A) onto Nipple (C) until tight.
using Mounting screws (E). Tighten the screws secur ely wit h a s c r ew driver.
CONNECTING THE WIRES (Fig 2)
BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
12. Tuck these wire connections neatly int o t he J unct ion Box .
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by t ightening Canopy Loop
collar (H) into Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture assembly sheet.
Fixture Name:
Sancerre 1425-5/9/3P/M1L WG
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixtur e from the carton and the yellow bag that
holds all parts. Check that all parts are included as shown in t he P ar ts and
Assembly Sheet.
2. Shut off the power at the circuit breaker and r em ove the old fixture from
ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread the other end of Nipple (C), with Canopy Loop (F) attached, into
Mounting Strap (D).
5. Place Lock Washer (B) over the end of Nipple (C) which should protrude
6. Take this mounting str ap as s embly and mount it to the ceiling junction box
For Chandelier Light Fixture
(G) and pass over Canopy Loop (F). Approximately one half of the canopy
loop exterior threads should be exposed. A dj us t until the desired height is
8. Assemble the fixture. Use an assistant or a secure suppor t to hold the
9.Thread the fixture wires and gr ound wire of the assembled fixture through
10. Attach the power supply wires to the fixture lead wires by connecting BLACK to
11. Attach the GROUND wire (GREEN or COPPER) from the Junction Box and the
fixture Ground Wire to the green Ground Screw on Mounting Bracket ( D) or c onnect
both wires together using the correct size of wire connectors.
NOTE: Twist the wires toget her in the s ame direction you twist the w ire connect or
onto the wires.
YOUR INSTALLATION IS NOW
COMPLETE. RETURN POWER TO
THE JUNCTION BOX AND TEST THE
For Customer Service, contact the place of purchase to arrange for replacement parts.
FIXTURE.
Loading...