Golden Lighting 1425-2W WG User Manual

Company Name:_______________________Co. Account #:_____________

to be filled out by retailer

PARTS & ASSEMBLY SHEET

Read and review ins tallation instructi on sheet, but do not

ASSEMBLING THE FIXTURE (Fig.1)

slide Candle Sleeve (P) into the hole and straighten.

chrome Candle Sleeve (P) as it will scratch and damage the finish of
the candle sleeve.

Fig 1

Fixture Name: Sancerre 1425-2W WG

This fixture assembled PO:__________ Date: ________

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are

missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.

PARTS LIST

Mounting Strap

1ea ∅4"*H2mm

Wire connectors Mounting Screws

3ea P3 Orange 2ea 8#32-IP*1-1/2" 2ea 8#32-IP*H3mm

Iron Tube crystal bobeche

2ea ∅1"*4-3/8"

Part Needed Quantity
Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

Mounting Screws Deco Nut

2ea 8#32-IP*1" 2ea 8#32-IP*H11mm

Hex Nut

2ea ∅4-1/4"*H15mm

FIXTURE ASSEMBLY INSTRUCTIONS

install before assembling the f ixture.

1. Crystal Chains (T) are individually wrapped and must be hung

1425-2W WG

piece by piece. Remove Crystal Chain (T) from the packaging and
examine the chain for Connection Pin (U). Drape Crystal Chain (T)
over Arm (S) so that Connection Pin (U) sits on top of Arm (S). This
will ensure proper draping length.

2. Attach Crystal Bobeche (Q) by sliding it over the socket. Then,

Note: Please do not attempt to slide Crystal Bobeche (Q) over the

NOTE: INSTALL THE GLASS ASSEMBLY AFTER THE

FIXTURE IS HUNG.

For Customer Service, contact the place of purchase to arrange for replacement parts.

INSTALLATION INSTRUCTIONS

HANGING THE FIXTURE (Fig.1)

illustrations and the Parts and Assembly Sheet.

strap.

threaded holes. Find the pair of holes that matches
the holes spacing in your fixture Back Plate (H) and

Mounting Strap (F) and secure with Hex Nut (G).

horizontal, as required by fixture type.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead

SMOOTH) and WHIT E to WHITE (or RIBBED).

together using the correct size of wire connectors. -

wires.

Junction Box.

FINISHING THE INSTALLATION(Fig.3)

the Junction Box and placing the fixture Back Plate
(E) over the two Mounting Screws (D), secure Back

tight as shown on Fig.1.

and Assembly Sheet.

Fig. 3

Fig. 1

Fig. 2

5. Attach Mounting Strap (F) to the Junction Box

securely with screw driver.

Fixture Name: Sancerre 1425-2W WG

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

1. Carefully remove the new fixture from the carton
and the yellow bag that holds all your parts. Check
that all parts are included as shown in the

2. Shut off power at the circuit breaker and remove
the old fixture from wall, including the old mounting

3. Mounting Strap (F) contains several pairs of

thread the two Mounting Screws (D) half way into

4. Place Mounting Strap (F) over Junction Box (A)
so that Mounting Screws (D) are vertical or

using the two mounting screws (H) and tighten

wires by connecting BLACK to BLACK (or

7. Attach the GROUND wire (GREEN or
COPPER) from the Junction Box and the fixture
Ground wire to the green Ground Screw (I) on
Mounting Bracket (F) or connect both wires

NOTE:Twist the wires together in the same
direction you twist the wire connector (L) onto the

8. Tuck these wire connections neatly into the

9. After tucking these wire connections neatly into

Plate (E) against the wall by threading two Deco
Nuts (O) over the two Mounting Screws (D) until

10. Install the light bulbs as per the fixture Parts

YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.