Page 1
y (E)
PARTS & ASSEMBLY SHEET
Fixture Name: Grace 1264-3P PW / RBZ
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy
1ea
Chain 6ft Wire connectors 2ea Bottom cap 1ea
Chain connector
Mounting Strap 1ea Hex Nut 2ea Finial 1ea
Green screws 1ea Rubber washer 1ea Metal washer 1ea
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
2ea
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Mounting
Screws
Canopy loop
and Canopy
loop collar
2ea Spacer 1ea
1ea Nipple 2ea
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Thread the Center column (C) onto the Socket
Assembl
2. Feed the fixture wires through the Top loop (A)
and pull the wires until taut.
3. Then screw the Top Loop (A) onto the Nipple (B)
until tight.
at the coupler (D).
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
1264-3P PW/RBZ
Fig 1
A
B
C
D
E
Page 2
y
PARTS & ASSEMBLY SHEET
Fixture Name: Grace 1264-3P PW / RBZ
4. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (C2) then
remove the excess Chain (C2) and discard it.
5. Use one chain connector (E2) to attach one end
of the chain to the Top loop (D2) and close the
chain connector.
6. Feed the fixture wires through the Chain (every
three links) and pull the wires until taut.
7. Slip Canopy loop collar (B2) over the chain, then
do the same with the canopy (F2).
8. When ready to complete the installation Use the
other chain connector and attach the other end of
the chain to the canopy loop (A2) and close the
chain connector.
9. Make sure the weight of the chandelier is
Fig 2
A2
B2
E2
C2
E2
D2
supported b
* You may now install the fixture.
NOTE: Finish installing the glass after the fixture is hung.
10. Thread the Nipple (F) into the Socket assembly (E),
lock into position by the tightening hex nut.
11. Install the light bulbs in accordance with the fixture’s
specifications.
12. Slide the Spacer (H), Glass shade (G), Rubber
washer (I), Metal washer (J) over the Nipple (F) secure
them by the Hex Nut (K).
13. Slide the Bottom Cap (L) over the Nipple (F), screw
the Finial (M) onto the Nipple (F) until tight.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)
.
the chain-not the electrical wire.
Fig 3
K
A
B
C
D
E
F
G
H
I
J
L
M
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
INSTALLATION INSTRUCTIONS
Fixture Name: Grace 1264-3P PW / RBZ
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as shown
in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling junction
box with junction box Screws (E). Tighten screw securely with
screw driver.
7. Unscrew the Canopy loop collar (H) from the Canopy loop.
Take the canopy and pass over the Canopy loop. approximatly
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *the Canopy loop collar
should fit snugly on the Canopy loop after the canopy is installed.
Remove Canopy and Canopy loop collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (D) or connect both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist the
wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
Fig. 1
JUNCTION BOX
(CEILING)
A
B
D
C
E
F
G
H
CHAIN
J
Fig. 2
FINISHING THE INSTALLATION
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar (H) into the Canopy Loop (F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...