How it Works
Golden Lighting
Loading...
1212-M3 AB
User Manual
3 pgs173.04 Kb0

Golden Lighting 1212-M3 AB User Manual

Download
Page 1
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Read and review installation instruction sheet before
For Customer Service, contact the place of purchase to arrange for replacement parts.
Bulb
(Not Provided)
J
M
N
O
P
Q
R
Fixture Name: Corsica 1212-M3 AB
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Wire Connectors Top Loop
1ea @130x19mm 3ea P4 Orange 1ea W40 x 70mm
Chain
1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector Nipple
Junction Box Screw
Canopy Loop with Collar
Spring Washer
Mounting Strap
w/ ground screw 1ea 3/4"X4" 2ea @3/8 x 3mm
Part Needed Quantity
Hex Nut
FIXTURE ASSEMBLY INSTRUCTIONS
assembling the fixture.
1. Thread the threaded pipe/stem ( P) int o t he coupling at center of f ixture body (R).
2. Place the stone column (O) and Top cap ( N) over the stem (P) and secure with the knurled nut ( M).
3. Thread the top loop (J) onto t he stem (P). Hand­tighten until snug.
Fig. 1

1212-M3 AB

4. Arrange the stone squar es for desired effec t .
NOTE: THE STONES ON THE COLUMN WILL NOT BE UNIFORM IN SIZE OR COLOR
Page 2
PARTS & ASSEMBLY SHEET
C
D
Bu
(Not Pr
J
M
N
O
P
Q
R
Fixture Name:Corsica 1212-M3 AB
ASSEMBLING THE FIXTURE (Fig. 2)
5. By measuring determine correct number of links needed for proper hanging height. Use a pair of pliers to open one link of the Chain (K) then remove the excess Chain (K) and discard it.
6. Use one chain connector (L) to attach one end of the chain to the Top loop (J) and close the chain connector.
7. Feed the fixture wires thr ough the Chain (every three links) and pull the wires until taut.
8. Slip Canopy loop collar (H) over the chain, then
7. Slip Canopy loop collar (H) over the chain, then do the
do the same with the canopy ( G).
same with the canopy (G).
9. When ready to complete the installation Use the
8. When ready to complete the installation Use the other
other chain connector and attach the other end of
chain connector and attach the other end of the chain to
the chain to the canopy loop (F) and close the
the canopy loop (F) and close the chain connector.
chain connector.
9. Make sure the weight of the chandelier will be supported
10. Make sure the weight of the chandelier will be
by the chain-not the electrical wire.
supported by the chain-not the electrical wire.
* You may now install the fixture.
* You may now install the fixture. Note: Complete these remaining steps after the fixture is hung.
11. Install the light bulbs (not provided) in accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
12. Carefully press the clips inside of the shade (Q) onto the bulb.
Fig. 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
Page 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
HANGING THE FIXTURE (Fig.1)
Fig. 1
L
B
C
A
JUNCTION BOX (CEILING)
D
E F
H CHAIN
G
BARE COPPER
(Ground)
GREEN (Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixtur e from the carton and the yellow
1. Carefully remove the new fixture from the carton and the yellow bag
bag that holds all parts. Check that all parts are
that holds all parts. Check that all parts are included as shown in the
in the illustration and parts list.
illustration and parts list.
2. Shut off the power at the circuit breaker and rem ove old fix ture
2. Shut off the power at the circuit breaker and remove old fixture from
from ceiling, including the old m ounting s tr ap.
ceiling, including the old mounting strap.
3. Thread Nipple(C) into Canopy Loop (F ) until snug.
3. Thread Nipple(C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attac hed
4. Thread other end of the Nipple (C) with Canopy Loop attached into
into Mounting Strap (D).
Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
5. Place Lock Washer (B) over end of Nipple (C) protruding through
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
Mounting Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
until tight.
6. Take this mounting strap assembly and mount to ceiling junction box
6. Take this mounting strap assem bly and mount to ceiling junction box with junction box Screws (E) . T ighten s c rew sec urely
with junction box Screws (E). Tighten screw securely with screw driver.
with screw driver.
7. Unscrew the Canopy loop collar(H )from the Canopy loop. Take the
7. Unscrew the Canopy loop collar (H )from the Canopy loop.
canopy and pass over the Canopy loop. approximatly one half of the
Take the canopy and pass over the Canopy loop. approx imatly one half of the canopy loop exterior threads should be expos ed.
canopy loop exterior threads should be exposed. Adjust until desired
Adjust until desired height is reached. *the Canopy loop c ollar
height is reached. *the Canopy loop collar should fit snugly on the
should fit snugly on the Canopy loop after the canopy is installed.
Canopy loop after the canopy is installed. Remove Canopy and
Remove Canopy and Canopy lock collar.
Canopy lock collar.
8. Assemble the fixture and have an assis tant or sec ure support
8. Assemble the fixture and have an assistant or secure support hold
hold the weight of the fixture while you com plete the wiring
the weight of the fixture while you complete the wiring connections.
connections.
9. Thread the fixture wires and ground wire of the assembled fixture
9. Thread the fixture wires and ground wire of the ass embled
through the canopy loop and nipple and into the outlet box.
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
CONNECTING THE WIRES (Fig. 2)
10. Attach the power supply wires to the fixture lead wires by
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or
connecting BLACK to BLACK (or SMOOTH) and WHITE to WHITE (or RIBBED).
RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the Junction
11. Attach the GROUND wire(GREEN or COPPER) from the
Box and the fixture Ground wire to the green Ground Screw on the
Junction Box and the fixture Ground wire to the green G round Screw on the Mounting Bracket (D) or connect both wires
Mounting Bracket (D) or connect both wires together using the correct
together using the correct size of wire connectors.
size of wire connectors.
NOTE: Twist the wires together in the same direction you twist the
NOTE: Twist the wires together in the same direction you twist the wire
wire connector onto the wires.
connector onto the wires.
12. Tuck these wire connections neatly into the J unc tion Box.
12. Tuck these wire connections neatly into the Junction Box.
13. Raise Canopy (G) to the ceiling and secure in place by tightening
13. Raise Canopy (G) to the ceiling and secure in place by tightening the Canopy loop collar ( H) into the Canopy Loop ( F) .
the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and shade as per the fixture ass embly
14. Install the light bulbs and glass shade as per the fixture assembly
sheet.
sheet.
INSTALLATION INSTRUCTIONS
Fixture Name: Corsica 1212-5/9/M3 AB
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
included as shown
YOUR INSTALLATIO N I S NOW CO MPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use