Golden Lighting 1212-9 AB User Manual
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Read and review installation instruction sheet before
assembling the fixture.
For Customer Service, contact the place of purchase to arrange for replacement parts.
J
M
N
O
P
Q
R
Bulb
(Not Provided)
Fixture Name: Corsica 1212-9 AB
This fixture assembled PO:__________ Date: ________
Notice:
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
PARTS LIST
Canopy Wire Connectors Top Loop
1ea @130x19mm 3ea P4 Orange 1ea W40 x 70mm
Chain
1ea 6ft x4.5mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain Connector Nipple
2ea @4.2X50mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 40mm
Mounting Strap
w/ ground screw
1ea 3/4"X4" 2ea @3/8 x 3mm
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
Junction Box
Screw
Canopy Loop
with Collar
Hex Nut
Spring Washer
1212-9 AB
Fig. 1
1. Thread the threaded pipe/stem ( P) int o t he
coupling at center of f ixture body (R).
2. Place the stone column (O) and Top cap ( N) over
the stem (P) and secure with the knurled nut ( M).
3. Thread the top loop (J) onto t he stem (P). HandÂtighten until snug.
4. Arrange the stone squar es for desired effec t .
NOTE: THE STONES ON THE COLUMN WILL NOT BE
UNIFORM IN SIZE OR COLOR
PARTS & ASSEMBLY SHEET
Fig. 2
C
D
J
M
N
O
P
Q
R
Bulb
(Not Prov
Fixture Name:Corsica 1212-9 AB
ASSEMBLING THE FIXTURE (Fig. 2)
5. By measuring determine correct number of links
needed for proper hanging height. Use a pair of
pliers to open one link of the Chain (K) then remove
the excess Chain (K) and discard it.
6. Use one chain connector (L) to attach one end of
the chain to the Top loop (J) and close the chain
connector.
7. Feed the fixture wires thr ough the Chain (every
three links) and pull the wires until taut.
8. Slip Canopy loop collar (H) over the chain, then
7. Slip Canopy loop collar (H) over the chain, then do the
do the same with the canopy ( G).
same with the canopy (G).
9. When ready to complete the installation Use the
8. When ready to complete the installation Use the other
other chain connector and attach the other end of
chain connector and attach the other end of the chain to
the chain to the canopy loop (F) and close the
the canopy loop (F) and close the chain connector.
chain connector.
9. Make sure the weight of the chandelier will be supported
10. Make sure the weight of the chandelier will be
by the chain-not the electrical wire.
supported by the chain-not the electrical wire.
* You may now install the fixture.
* You may now install the fixture.
Note: Complete these remaining steps after the
fixture is hung.
11. Install the light bulbs (not provided) in
accordance with the fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
12. Carefully press the clips inside of the shade
(Q) onto the bulb.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...