Golden Lighting 1157-4P CHAB User Manual

2ea @3/8 x 3mm

Part Needed Quantity

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

Cap (T) over the Metal Frame.

protection during installation to avoid injury.

Fig. 1

For Customer Service, contact the place of purchase to arrange for replacement parts.

Read and review installation ins truction sheet before
assembling the fixture.

PARTS & ASSEMBLY SHEET

Company Name:_______________________ Co. Account #:_____________

to be filled out by retailer

This fixture assembled PO:__________ Date: _ ____ ___

Fixture Name: Payton 1157-4P CH/AB

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Canopy Wire Connectors Top Loop

1ea D5"×H1" 3ea P4 Orange 1ea W60 x 70mm

Chain

1ea 6ft x3.8mm 2ea 8/32" x 1" 1ea @15 x 2mm

Chain
Connector

2ea @4.2X50mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 40mm

Mounting Strap

w/ ground screw
1ea 3/4"X4"

Part Needed Quantity

Junction Box
Screw

Canopy Loop
with Collar

Hex Nut

Spring Washer

Nipple

FIXTURE ASSEMBLY INSTRUCTIONS

1157-4 CH/AB

1. Use Deco Nuts (S) to attach Circular End Cap
(T) to Metal Frame (N).

2. Carefully slide Glass Panels (U) into Metal
Frame (N). Then, lower the other Circular End

Note: Glass edges may b e sharp. Wear gloves for

If the glass can not be successfully placed into
the framework, please relax and adjust the iron
bar slightly. It is suggested that this be completed
by two people.

Fig. 2

For Customer Service, contact the place of purchase to arrange for replacement parts.

PARTS & ASSEMBLY SHEET

Fixture Name: Payton 1157-4P CH/A B

ASSEMBLING THE F IXT U RE (Fig. 2)

3. Thread Threaded Stem (P) into the coupling at
centre of Fixture Body (O).

4. Thread the Top Loop (J) onto Stem (I) and (P).
Hand-tighten until snug.

5. Lower the fixture over the glass cage, use the
round Deco Nuts (M) to secure Arms (L) t o th e
cage (N).

6. Measure to determine the correct number of
links needed for the proper hanging height. Use a
pair of pliers to open one link of Chain (K). Then,

7. Slip Canopy loop collar (H) over the chain, then do the

remove and discard the excess Chain.

same with the canopy (G).

7. Use one Chain Connector (L) to attach one end

8. When ready to complete the installation Use the other

of the chain to Top Loop (J) and close the chain

chain connector and attach the other end of the chain to

connector.

the canopy loop (F) and close the chain connector.

8. Feed the fixture wires through the chain (every

9. Make sure the weight of the chandelier will be

three links) and pull the wires until taut.

supported by the chain-not the electrical wire.

9. Slip Canopy Loop Collar (H) over the chain, then

* You may now install t he fixture.

do the same with Canopy (G).

10. To complete the installation, use the other
chain connector and attach the other end of the
chain to the Canopy Loop (F) and close the chain
connector.

11. Make sure the weight of the chandelier will be
supported by the chain, not the electrical wire.

* You may now install the fixture.
Note: Complete these remaining steps after the

fixture is hung.

12. Install the light bulbs (not provided) in
accordance with the fixture's specifications.

(DO NOT EXCEED MAXIMUM WATTAGE RATING)

13. Carefully press the clips inside of Shade (Q)
onto the bulb.