Page 1
Junction Box
Screw
Mounting Strap
w/ ground screw
Top/Bottom
Threaded Rod
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Fig. 1
NOTE: INSTALL THE GLASS ASSEMBLY AFTER THE
FIXTURE IS HUNG.
PARTS & ASSEMBLY SHEET
Read and review installation instruction sheet before
assembling the fixture.
This fixture assembled PO:__________ Date: ________
Canopy Loop
with Collar
For Customer Service, contact the place of purchase to arrange for replacement parts.
place with Check Ring (R) until tight.
PARTS LIST
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Fixture Name: Pember ly Court 1089-D5 RSB-PRL
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note on this sheet and contact the place of purchase to arrange for
replacement parts.
Canopy Wire connectors Top loop
1ea @5-1/2"X1-1/4" 3ea P3 Orange 1ea @3/8 x 65mm
Chain
1ea 6ft x4.2mm 2ea 8/32" x 1" 1ea @15 x 2mm
Chain connector Nipple
2ea @4.2X50mm 1ea @3/8 x 40mm x 5mm 1ea @3/8 x 55mm
Hex Nut
1ea 3/4"X4" 1ea @3/8 x 45mm/@3/8 x 60mm
Top Cover Check ring Top Cap
1ea @80 x 30mm 1ea @16 x 3mm 1ea @85 x 25mm
Finial Bottom Cover Bottom Cap
1ea @3/8 x 25mm 1ea @94 x 20mm 1ea @100x45mm
Part Needed Quantity
IXTURE ASSEMBLY INSTRUCTIONS
F
2ea/2ea @3/8 x 3mm/@3/8 x 5mm
Spring Washer
1089-D5RSB
ASSEMBLING THE FIXTURE (Fig. 1)
1. If the arms are packed closed, gently spread the
arms until evenly spaced .
2. Feed the fixture wires through the T op Threaded
Rod (N), Top Cover (O), Hex Nut (P), T op Cap ( Q ) ,
Check Ring (R) and Top Loop (J) and pull the wires
until taut.
3. Turn Top Threaded Rod (N) into the coupling at the
top center of Frame (M).
4. Slide the Top Cover (O) over Top Threaded Rod
(N). Secure in place with the Hex Nut (P) until tight.
Slide Top Cap (Q) over Threaded Rod (N), secure in
Page 2
For Customer Service, contact the place of purchase to arrange for replacement parts.
and pull the wires until taut.
Fig 2
PARTS & ASSEMBLY SHEET
Fixture Name: Pemberly Court 1089-D5 RSB-PRL
C
D
6. By measuring, determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (K). Remove the excess chain and discard
it.
7. Use one of Chain Connector (L) to attach one end of the
chain to the Top Loop (J) and close the chain connector.
8. Feed the fixture wires through Chain (K) (every three links)
9. Slip Canopy Loop Collar (H) over the chain, then do the
same with Canopy (G).
10. When ready to complete the installation, use the other
chain connector and attach the other end of Chain (K) to
Canopy Loop (F) and close the chain connector.
11. Make sure the weight of the chandelier will be supported
by the chain-not the electrical wire.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
12. Turn the Bottom Threaded Rod (S) into the coupling at
bottom center of the Frame (M).
13. Slide the Bottom Cover (T) over the Bottom Threaded
Rod (S). Secure in place with Hex Nut (P) until tight. Slide
Bottom Cap (U) over the Bottom Threaded Rod (S), secure
in place with Finial (V). Twist until tight.
14. Slide Glass Shade (W) over the socket of Frame (M) and
secure Glass Shade (W) by threading Socket Ring (X) onto
the socket of Frame (M) until tight.
15. Install the light bulb (not provided) in accordance with the
fixture's specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
Page 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
HANGING THE FIXTURE (Fig.1)
junction box Screws (E). Tighten scr ew securely with screw driver.
CONNECTING THE WIRES (Fig 2)
BLACK to BLACK (or SMOOTH) and W H ITE to WHITE (or RIBBED).
13. Raise Canopy (G) t o the ceiling and sec ure in place by tighteni ng the
14. Install the light bulbs and glass shade as per the fi xture assembly sheet.
Fig. 2
Fig. 1
canopy loop and nipple and into the outlet box.
INSTALLATION INSTRUCTIONS
L
B
C
A
JUNCTION BOX
(CEILING)
D
E
F
H
J
CHAIN
G
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Pemberly Court 1089-D5 RSB-PRL
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
1. Carefully remove the new fixture from the carton and the yellow bag that
holds all your part s. Check that all parts are included as shown in the
illustrations and the Parts and Assembly Sheet.
2. Shut off the power at the circuit breaker and remove old f ixture from ceiling,
including the old mount ing strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached into Mounting
Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding through Mount ing
Strap (D) and thread Hex Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling junction box with
For Chandelier Light Fixture
7. Unscrew Canopy Loop Collar (H) from t he C anopy loop. Take the canopy
and pass over the Canopy loop. approximately one half of the canopy loop
exterior threads s hould be exposed. Adjust until desired height is reached. *the
Canopy loop collar should fit snugly on the Canopy loop after the canopy is
installed. Remove Canopy and C anopy lock collar .
8. Assemble the fixture and have an assist ant or secure support hold the weight
of the fixture while you complete the wiri ng connections.
9. Thread the fixture wi res and ground wire of t he assembled fixture t hrough the
10. Attach the power supply wires to t he fixture lead wires by connecting
11. Attach the GROUND w ire(GREEN or COPPER) from the Junct ion Box and
the fixture Ground wir e to the green Ground Screw on the Mounting Bracket (D)
or connect both wires together usi ng the correct s ize of wire connect ors.
NOTE: Twist the w ires together in the same direction you twist the wire
connector onto the wires.
12. Tuck these wi re connections neat ly into the Junction Box.
Canopy loop collar(H) into the Canopy Loop(F)
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX
AND TEST THE FIXTURE.
Loading...