Golden Lighting 1089-BA3 RSB-PRL User Manual

1089-BA3 RSB-140411

Reason why ( missing, scratched, broken glass, bent, bad finish)

Comments

PARTS & ASSEMBLY SHEET

This fixture assembled PO:__________ Date: ________

Company Name:_______________________Co. Account #:_____________

below to be filled out by retailer

Read and review installation instruction sheet before
assembling the fixture.

NOTE: INSTALL THE GLASS ASSEMBLY AFTER

1. Slide Glass Shade (H) over Socket (I) and secure Glass

Fig. 1

Fixture Name: Pemberly Court 1089-BA 3 R S B-PRL

Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or

damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.

PARTS LIST

Mounting Strap

1ea 4"X3" 2ea 8/32"X1" 2ea 8/32"X28mm

Wire Connector Hex Nut

3ea P3 Orange 2ea 8/32"X3.5mm 2ea 9X9.5mm

Green Ground
Screw

1ea 8/32"X10mm

Part Needed Quantity
Part Needed Quantity

Junction Box
Screw

Mounting Screw

Deco Nut
(round nut)

FIXTURE ASSEMBLY INSTRUCTIONS

1089-BA3 RSB

Shade (H) by threading Socket Ring (J) onto Socket (I).

2. Install the light bulbs in accordance with fixture's
specifications.

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)

THE FIXTURE IS HUNG.

For Customer Service, contact t he place of purchase to arrange for replacement parts.

Fig. 3

Fig. 1

Fig. 2

HANGING THE FIXTURE (Fig. 1)

Back Plate (K) and thread the two Mounting Screws (B) half way

CONNECTING THE WIRES (Fig. 2)

FINISHING THE INSTALLATION (Fig. 3)

11. Install the glass as per the fixture assembly instructions

POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

INSTALLATION INSTRUCTIONS

BARE COPPER

(Ground)

GREEN
(Ground)

FIXTURE WIRES

SMOOTH (BLACK)

RIBBED (WHITE)

BLACK

WHITE

HOUSE WIRES

Fixture Name: Pemberly Court 1089-BA3 RSB-PRL

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

1. Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustrations and the Parts and
Assembly Sheet.

2. Shut off power at the circuit breaker and completely remove
the old fixture from wall, including the old mounting strap.

3. Mounting Strap (A) contains several pairs of threaded holes,
find the pair of holes that match the holes spacing in your fixture

into the Mounting Strap (A).

4. Place the Mounting Strap (A) over Junction Box (E) so that
Mounting Screws (B) are vertical or horizontal, as required by
fixture type.

For Wall Mount Light Fixture

5. Attach Mounting Strap (A) to Junction Box (E) using the two
mounting screws (D). Tighten the screws securely.

5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).

6. Attach the GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on Mounting Bracket (A) or connect both wires together
using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.

7. Tuck these wire connections neatly into the Junction Box.

9. Place fixture Back Plate (K), over the Mounting Screws (B),
so that they protrude through the holes in Back Plate (K).

10. Thread Decorative Nuts (L) onto Mounting Screws (B) and
continue turning until Back Plate (K) is snug against the wall.

YOUR INSTALLATION IS NOW COMPLETE. RETURN

For Customer Service, contact the place of purchase to arrange for replacement parts.