Page 1
1ea 3"X4" 2ea 8/32"X28mm 2ea 8/32X1"
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled ou t by retailer
Read and review installation instruction sheet before
assembling the fixture.
NOTE: I
Fig. 4
Fixture Name: Pemberly Court 1089-1W RSB- PRL
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are missing or
damaged, please note on this sheet and contact the place of purchase to arrange for replacement parts.
Mounting strap Mounting Screw Mounting screw
Wire connector Hex Nut Deco nut
3ea P3 Orange 2ea 8/32"X3.5mm 2ea @15X12mm
Green Ground
screw
1ea 8/32"X10mm
Part Needed Quantity
Part Needed Quantity
(round nut)
FIXTURE ASSEMBLY INSTRUCTIONS
1089-1W RS B
1. Slide Glass Shade (K) over Socket (M) and secure
Glass Shade (K) by threading Socket Ring (L) onto
Socket (M) until tight.
2. Install the light bulb in accordance with the fixture's
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE
RATING!)
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact t he place of purchase to arrange for r eplacement parts.
1089-1W RSB-140411
Page 2
INSTALLATION INSTRUCTIONS
Fig. 3
Fig. 1
Fig. 2
HANGING THE FIXTURE (Fig. 1)
CONNECTING THE WIRES (Fig. 2)
7. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig.3)
), over the Mounting screws(B), so
11. Install glass as per the fixture assembly instructions
TO THE JUNCTION BOX AND TEST THE FIXTURE.
BARE COPPER
(Ground)
GREEN
(Ground)
FIXTURE WIRES
SMOOTH (BLACK)
RIBBED (WHITE)
BLACK
WHITE
HOUSE WIRES
Fixture Name: Pemberly Court 1089-1W RSB-PRL
For Wall Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig. 1)
1. Carefully remove the new fixture from the carton and the yellow
1. Carefully remove the new fixtur e from the carton and t he
yellow bag that holds all your parts. Check that all part s ar e
bag that holes all your parts. Check that all parts are included as
included as shown in the illustrations and the Parts and
shown in the illustration and parts list.
Assembly Sheet.
2. Shut off power at the circuit breaker and remove the old fixture
from wall, including the old mounting strap.
2. Shut off power at the circuit br eaker and completely r emov e
3. The Mounting Strap(A) contains several pairs of threaded holes,
the old fixture from wall, including the old mounting strap.
find the pair of holes that match the holes spacing in your fixture
Back Plate (K) and thread the two Mounting Screws(B) half way
3. Mounting Strap (A) contains several pairs of threaded holes,
into the Mounting Strap(A).
find the pair of holes that match the holes spacing in your
4. Place the Mounting Strap (A) over the Junction Box (E) so the
fixture Back Plate (K) and thread the two Mounting Scr ew s ( B)
half way into the Mounting Strap (A).
Mounting Screws (B) are vertical or horizontal, as required by
fixture type.
4. Place the Mounting Strap (A) over Junction Box (E) so that
5. Attach the Mounting Strap (A) to the Junction Box (E) by using
Mounting Screws (B) are vertical or horizontal, as required by
the two mounting screws(D). Tighten the screws securely.
fixture type.
5. Attach Mounting Strap ( A) t o Junction Box (E) using the t w o
5. Attach the power supply wires to the fixture lead wires by
mounting screws (D). Tighten the screws securely.
connecting BLACK to BLACK (or SMOOTH) and WHITE to
CONNECTING THE WIRES (Fig. 2)
WHITE (or RIBBED).
5. Attach the power supply wires to the fixture lead wires by
6. Attach the GROUND wire(GREEN or COPPER) from the
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (A) or connect both wires
6. Attach the GROUND wire (GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
together using the correct size of wire connectors.
Screw on the Mounting Bracket (A) or connect both w ir es
NOTE: Twist the wires together in the same direction you twist the
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
wire connector onto the wires.
the wire connector onto the w ir es.
7. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig. 3)
9. Place the fixture Back Plate (J
9. Place the fixture Back Plate (J), over the Mounting sc r ew s
(B), so that they protrude t hr ough the holes in the Back Plate
they protrude through the holes in the Back Plate (J).
(J).
10. Thread the Deco Nuts (H) onto the Mounting Screws (B) and
10. Thread Decorative Nuts (H) onto Mounting Screws (B) and
continue turning until Back Plate (J) is snug against the wall.
continue turning until the Back Plate (J) is snug against the wall.
11. Install the glass as per the fixtur e assembly instructions.
YOUR INSTA LLATION IS NOW COMPLET E . RE TURN
POWER TO THE JUNCTION BOX AND TE ST THE FIXTURE.
YOUR INSTALLATION IS NOW COMPLETE. RETURN POWER
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...