Golden Lighting 1051-M1L SBZ User Manual
F
additional rods onto the wire.
the Swivel assembly (F) to the Rod (G).
PARTS & ASSEMBLY SHEET
Fixture Name: Hidalgo 1051-M1L SBZ
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Circular
Mounting strap
Green screws 1ea Deco or Ball Nut 2ea Wire connectors 3ea
Rod 3 ea
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
1ea
Mounting screws
8/32T*1-1/2"L
2ea Box Screw 2ea
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1051-M1L SBZ
1. By measuring determine correct number of rods
needed for proper hanging height. There are 3 optional
12" rods included.To shorten the fixture slide the excess
12" rods off the wire.To lengthen the fixture thread the
2. Pull the fixture's wire through the Rods (G).
3. Thread Rod/rods (G) into Fixture frame (H) using the
nipples until tight, repeat for the additional rods. Thread
NOTE: I
NSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
4. Place the Glass Shades (J) over the Threaded
Sockets(I) and secure by threading the Socket Ring (K)
to Threaded Socket (I) until tight..
5. Install the light bulbs in accordance with the fixture's
Fig 1
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
CONNECTING THE WIRES (Fig 2)
WHITE to WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from the
twist the wire connector onto the wires.
INSTALLATION INSTRUCTIONS
3. The Circular Mounting Strap (A) contains several pairs of
Fixture Name: Hidalgo 1051-M1L SBZ
For Mini pendant Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Semi flush (Fig. 1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove the old
fixture from ceiling, including the old mounting strap.
threaded holes, find the pair of holes that match the hole
spacing in your fixture Back Plate (D) and thread the two
Mounting Screws (C) half way into the Mounting Strap (A)
facing down,Secure in place with hex nuts. These will have
their threaded ends protrude through the two holes in the
fixture canopy (D).
4. Place the Mounting Strap (A) over the junction box.
5. Attach the Mounting Strap (A) to the Junction Box using
the two mounting screws (B). Tighten the screws (B)
securely with screw driver.
6. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
Fig. 1
Fig. 2
Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (A) or connect
both wires together using the correct size of wire
connectors.
NOTE:Twist the wires together in the same direction you
8. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSALLATION (Fig.3)
9. Place the fixture’s canopy over the Mounting Strap (A)
and over the Mounting Screws (C), adjust the fixture
canopy (D) until the Mounting Screws (C) protrude out from
the canopy (D) and secure the fixture against the ceiling by
threading the decorative nuts (E) until tight.
10. Install the light bulbs and glass shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 3
Loading...