Mounting screws
Fixture Mounting
Part Needed
Quantity
Reason why
( missing, scratched, broken glass, bent, bad finish)
Comments
thread the Hex Nut (F) onto Nipple (G) until tight.
(M) until tight.
NOTE: I
PARTS & ASSEMBLY SHEET
Please review the parts listing and check for all parts before assembling the fixture. If any parts are
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Fixture Name: Hidalgo 1051-FM SBZ
This fixture assembled PO:__________ Date: ________
Notice:
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
screws
Mounting strap 1ea
Hex nut 3/8"
4mm
2ea Finial 1ea
8/32T*1-1/4"L 2ea
8/32T*1-1/2"L 2ea
Green screw
1ea
Nipple
Wire connectors 3ea
Part Needed Quantity
F
IXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1. Thread the Nipple (G) into the Coupling (E), and then
2.Install the light bulbs in accordance with the fixture's
specifications.
3. Place Glass Shade (H) over the Ceiling Pan (D). The
Nipple (G)shall protrude the bottom hole of the Glass Shade
1ea Bottom Cap 1ea
Fig 1
Metal Washer
1051-FM SBZ
1ea
(H).
4. While holding the Glass Shade (H) slide washer(J) over
Nipple (G) and thread Hex nut (K) until tight.
5. Slide Bottom Cap (L) over Nipple (G) and thread the Finial
(DO NOT EXCEED THE MAXIMUN WATTAGE RATING)
NSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
CONNECTING THE WIRES (Fig 2)
wires together using the correct size of wire connectors. -
twist the wire connector onto the wires.
INSTALLATION INSTRUCTIONS
）
4. Attach Mounting Strap (B) to the junction box using the
Fixture Name: Hidalgo 1051-FM SBZ
For Flush Mount Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE（Fig.1
1. Carefully remove the new fixture from the carton and
the yellow bag that holds all parts. Check that all parts
are included as shown in the illustration and parts list.
2. Shut off power at the circuit breaker and remove old
fixture from ceiling, including the old mounting strap.
3. Thread the two Fixture Mounting Screws (A) into the
pre-drilled Hole in the Mounting Strap (B) spaced the
same distance apart as the hole in the Ceiling Pan.
two Screws (C).
5. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED). 6. Attach the
GROUND wire(GREEN or COPPER) from the Junction
Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (B) or connect both
Fig. 1
D
Fig. 2
NOTE:Twist the wires together in the same direction you
7. Tuck these wire connections neatly into the Junction
Box.
FINISHING THE INSTALLATION (Fig.3)
8. Finish mounting the Ceiling Pan (D) by placing it over
the Mounting Strap (B) as shown on FIG.1. Rotate the
Pan until the Mounting screws (A) protrude through the
“Keyholes” located in the bottom of Ceiling Pan (D).
Using a screw driver, secure the Ceiling Pan (D) by
screwing Mounting Screws (A) until taut.
9. Install the light bulbs in accordance to the fixture’s
specifications.
10. Install the glass shade as per the assembly
instructions.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.
Fig. 3
For Customer Service, contact the place of purchase to arrange for replacement parts.
Loading...