Golden Lighting 1051-BA4 SBZ User Manual

Ring (J) to Socket (F) until tight.

fixture's specifications.

PARTS & ASSEMBLY SHEET

Fixture Name: Hidalgo 1051-BA4 SBZ

This fixture assembled PO:__________ Date: ________

Notice:

are missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.

PARTS LIST

Anchor 2ea

Anchor Screw 2ea

Green Ground
Screw

Part Needed Quantity

Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments

F

IXTURE ASSEMBLY INSTRUCTIONS

Please review the parts listing and check for all parts before assembling the fixture. If any parts

Company Name:_______________________Co. Account #:_____________
to be filled out by retailer

1ea

Junction Box
Screw

Wire
Connnector

Deco Nut
(round nut)

2ea

2ea

2ea

Mounting
Plate

1 ea

Read and review installation instruction sheet
before assembling the fixture.

1.Slide the Glass Shade ( H ) over Socket (F) and
secure Glass Shade (H) by threading the Socket

2. Install the light bulbs in accordance with the

(DO NOT EXCEED THE MAXIMUM WATTAGE RATING)

NOTE: I

NSTALL THE GLASS ASSEMBLY

AFTER THE FIXTURE IS HUNG.

1051-BA4 SBZ

Fig 1

For Customer Service, contact the place of purchase to arrange for replacement parts.

5. Attache the Mounting Plate (B) to Junction Box by using the

WHITE (or RIBBED).

together using the correct size of wire connectors.

NOTE: Twist the wires together in the same direction you twist

the wire connector onto the wires.

FINISHING THE INSTALLATION (Fig.3)

Junction Box and place the fixture Front Plate (G) over the two

(C) until snug against the wall.

assembly sheet.

)

included as shown in the illustration and parts list.

fixture from wall, including the old mounting strap.

3. Hold Mounting Plate (B) up against the wall aligning the two

INSTALLATION INSTRUCTIONS

Fixture Name: Hidalgo 1051-BA4 SBZ

For Wall Mount Light Fixture

WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.

HANGING THE FIXTURE (Fig.1

1. Carefully remove the new fixture from the carton and the

yellow bag that holes all your parts. Check that all parts are

2. Shut off power at the circuit breaker and remove the old

holes in the Junction Box with appropriate slots in the

Mounting Plate (B). Then while the Mounting Plate (B) is

leveled horizontally, use a pen or pencil to make a mark on

the wall at holes located near each end of mounting Plate (B).

Set aside the Mounting Plate (B) and insert W all Anchors (A)

into the two marks made on the wall.

4. Thread the supply wires and ground wire from Junction Box

through center holes in Mounting Plate (B).

two Junction Box Screws(E). If Anchors (A) were attached to

the wall, secure the Mounting Plate (B) with two Anchors

Screws (D) to corresponding holes.

CONNECTING THE WIRES (Fig 2)

6. Attach the power supply wires to the fixture lead wires by

connecting BLACK to BLACK (or SMOOTH) and WHITE to

Fig. 1

Fig. 2

7. Attach the GROUND wire(GREEN or COPPER) from the

Junction Box and the fixture Ground wire to the green Ground

Screw on the Mounting Plate (B) or connect both wires

8. Tuck these wire connections neatly into the Junction Box.

Fig. 3

9. After tucking these wire connections neatly into the

Mounting Screws (C) and secure against the Mounting Plate

by threading two Deco Nuts (I) over the two Mounting Screws

10. Install the light bulbs and glass shade as per the fixture

YOUR INSTALLATION IS NOW COMPLETE. RETURN

POWER TO THE JUNCTION BOX AND TEST THE FIXTURE.

For Customer Service, contact the place of purchase to arrange for replacement parts.