Golden Lighting 1035-BA2 CH User Manual
Fig. 3
Fig. 1
Fig. 2
Hanging the Fixture
parts are included as shown in the illustration and parts list.
fixture from wall, including the old mounting strap.
Socket Ring (L) to Socket (G) until tight.
10. Thread the Bulb Shield (K) to Socket (G).
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
INSTALLATION INSTRUCTIONS
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
B
A
D
C
FIXTURE WIRES
HOUSE WIRES
Fig.2
JUNCTION BOX
C
B
A
E
D
F
BARE COPPER
GREEN
(Ground)
FIXTURE WIRES
SMOOTH ( or BLACK)
RIBBED ( or WHITE)
BLACK
(Hot)
WHITE
(Netural)
HOUSE WIRES
G
H
L
K
J
I
M
A
N
Fixture Name: Neeva 1035-BA2 CH
1.Carefully remove the new fixture from the carton and the
yellow bag that holds all your parts. Check that all
For Wall Mount Light Fixture
2. Shut off power at the circuit breaker and remove the old
3 Attach the Back Plate (B) to the Junction Box (C) by
using the two Junction Box Screws (D). Tighten the
screws securely.
CONNECTING THE WIRES (Fig. 2)
4. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and
WHITE to WHITE (or RIBBED).
5. Attached the GROUND wire (GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw on the Back Plate (B) or connect both wires
together using the correct size of wire connectors
NOTE: Twist the wires together in the same direction when
twist the wire connector onto the wires.
6. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSTALLATION (Fig. 3)
7. Place the fixture Front Plate (H), over the
Back Plate (B), and tighten with Mounting Screws (A).
8. Slide the Glass Shade (I) and Spacer (J) over
Socket (G), using Socket Wrench (N) to thread
9. Install Bulb (M) in accordance with the
fixture's specifications .
For Customer Service, contact the place of purchase to arrange for replacement parts.
Green Ground
#8-32N*H25mm
Socket Wrench
Wire Connector
2 ea
Φ26*H50MM
14*13*44MM
Comments
PARTS & ASSEMBLY SHEET
This fixture assembled PO:__________ Date: ________
Read and review installation instruction sheet before
assembling the fixture.
PARTS LIST
Company Name:_______________________Co. Account #:_____________
below to be filled out by retailer
Fig. 4
1. Place the fixture Front Plate ( H ), over the
Socket Ring (L) to Socket (G) until tight.
4. Thread the Bulb Shield (K) to Socket (G).
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
FS
G9
130V 75W
G
H
L
K
J
I
M
A
N
Fixture Name: Neeva 1035-BA2 C H
Notice:
are missing or damaged, please note on this sheet and contact the place of purchase to arrange for
replacement parts.
Screw
1 ea
#8-32N*H10mm
3 ea
P3
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Please review the parts listing and check for all parts before assembling the fixture. If any parts
Junction Box
Screw
2 ea
Bulb Shield
1 ea
Φ28*127MM
Xenon Bulb
2 ea
FIXTURE ASSEMBLY INSTRUCTIONS
1035-BA2
Back Plate (B) (shown in Fig. 1), and tighten with Mounting
Screws (A).
2. Slide the Glass Shade (I ) and Spacer (J) over
Socket (G), using Socket Wrench (N) to thread
3. Install Bulb (M) in accordance with the
fixture's specifications .
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
For Customer Service, contact t he place of purchase to arrange for replacement parts.
Loading...