PARTS & ASSEMBLY SHEET
(DO NO
Fixture Name: Cerchi 1030-SF CH
This fixture assembled PO:__________ Date: ________
Notice:
are missing or damaged, please note on this sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST
Canopy
Mounting
Strap
Chain 6ft
Chain
connector
Canopy Loop
with Collar
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
Please review the parts listing and check for all parts before assembling the fixture. If any parts
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
1ea
1ea
2ea
1ea Hex Nut 2ea Finial 1ea
Screws 2ea Top loop 1ea
Spring Washer
Wire
Connectors
Mounting
Screws
1ea Mounting Strap 1ea
5ea Nipple 1ea
4ea Deco Nut 2ea
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture.
ASSEMBLING THE FIXTURE as Semi flush (Fig. 1)
1. Grasp the fixture wires and align the Fixture Nipple to
socket assembly coupler (G) and thread together until
tight. Ensure the fixture wires are not pinched in the
coupler.
2. Gently spread the Frame arms (Y) until evenly spaced
if arms are packed closed.
3. The Center column rings may be turned to your
desired angle.
4. Slide Shade (H) through Fixture connector (K) and
secure Shade (H) to Arms (Y) with Screws (N).
Note: Complete these remaining steps after the fixture
is hung.
5. Install light bulbs in accordance with fixture's
specifications.
6. Slide Diffuser ( I ) to Shade (H) and secure in place by
threading Bottom Finial (J) to the Fixture connector (K).
T EXCEED MAXIMUM WATTAGE RATING)
NOTE: INSTALL THE DIFFUSER AFTER THE
FIXTURE IS HUNG.
Fig 1
1054-SF ST
B
F
E
L
Y
G
K
H
I
J
For Customer Service, contact the place of purchase to arrange for replacement parts.
PARTS & ASSEMBLY SHEET
Fixture Name: Cerchi 1030-SF CH
ASSEMBLING THE FIXTURE as Chain hung (Fig.2)
1. Remove the Circular strap from top of Fixture and
replace the long mounting screws with two short screws
(Z) to hold the Deco nuts (E) in place on the fixture Top
cap (F).
2. Feed the fixture wires through the Top loop (W) and
pull the wires until taut. Then screw the Top Loop (W) to
the coupling in top cap (F) until tight.
3. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers to
open one link of the Chain (T) then remove the excess
Chain (T) and discard it.
4. Use one chain connector(V) to attach one end of the
chain to the Top loop (W) and close the chain connector.
5. Feed the fixture wires (U) through the Chain (every
Fig 2
M
N
O
C
P
Q
R
S
T
U
V
three links) and pull the wires until taut.
6. Slip Canopy loop collar (S) over the chain, then do the
same with the canopy (Q).
.
7. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to
the canopy loop (R) and close the chain connector.
8. Make sure the weight of the chandelier is supported
by the chain-not the electrical wire.
Note: Complete these remaining steps after the fixture
is hung.
8. Slide Shade (H) through Fixture connector (K) and
secure Shade (H) to Arms (Y) with Screws (N).
9. Install light bulbs in accordance with fixture's
specifications.
10. Slide Diffuser ( I ) to Shade (H) and secure in place
Fig 3
L
Z
Y
W
F
E
G
K
H
I
by with Bottom Finial (J) to the Fixture connector (K).
11. The Center column rings may be turned to your
desired angle.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
J
INSTALLATION INSTRUCTIONS
Fixture Name: Cerchi 1030-SF CH
For Semi Flush / Convertible Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE as Semi flush (Fig. 1)
1. Carefully remove the new fixture from the carton
and the yellow bag that holds all your parts. Check
that all parts are included as shown in the illustration
and parts list.
2. Shut off power at the circuit breaker and remove the
old fixture from ceiling, including the old mounting
strap.
3. The Circular mounting strap (B ) contains several
pairs of threaded holes, find the pair of holes that
match the hole spacing in your fixture Back Plate (D)
and thread the two Mounting Screws (A) half way into
the Mounting strap (B) facing down, Secure in place
with hex nuts. These will have their threaded ends
protrude through the two holes in the fixture
canopy(F).
4. Place the Mounting Strap (B ) over the junction box.
5. Attach the Mounting Strap (B) to the Junction Box
using the two mounting screws (C). Tighten the
screws (C) securely with screw driver.
Fig. 1
JUNCTION BOX
(CEILING)
A
B
C
D
F
E
CONNECTING THE WIRES (Fig 2)
6. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
7. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (B) or connect both
wires together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
8. Tuck these wire connections neatly into the Junction Box.
FINISHING THE INSALLATION (Fig.3)
9. Place the fixture’s canopy over the Mounting Strap (B)
and over the Mounting Screws (A), adjust the fixture canopy
(F) until the Mounting Screws (A) protrude out from the
canopy (F) and secure the fixture against the ceiling by
threading the decorative nuts (E) until tight.
10. Install the light bulbs and fabric shade as per the fixture
assembly sheet.
YOUR INSTALLATION IS NOW COMPLETE. RETURN
POWER TO THE JUNCTION BOX AND TEST THE
FIXTURE.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig. 2
FIXTURE WIRES
SMOOTH (BLACK)
Fig. 3
RIBBED (WHITE)
BARE COPPER
(Ground)
HOUSE WIRES
BLACK
WHITE
A
B
C
D
F
E
GREEN
(Ground)
INSTALLATION INSTRUCTIONS
Fixture Name: Cerchi 1030-SF CH
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the
yellow bag that holds all parts. Check that all parts are
included as shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old
fixture from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop
attached into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread spring washer (B)
and Hex Nuts (A) onto Nipple until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Screws (E). Tighten screw
securely with screw driver.
7. Unscrew the Canopy loop collar (H) from the Canopy
loop. Take the canopy and pass over the Canopy loop.
approximatly one half of the canopy loop exterior threads
should be exposed. Adjust until desired height is reached.
*the Canopy loop collar should fit snugly on the Canopy loop
after the canopy is installed. Remove Canopy and Canopy
lock collar.
8. Assemble the fixture and have an assistant or secure
support hold the weight of the fixture while you complete the
wiring connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet
box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires
by connecting BLACK to BLACK (or SMOOTH) and WHITE
to WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from
the Junction Box and the fixture Ground wire to the green
Ground Screw on the Mounting Bracket (B) or connect both
wires together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you
twist the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction
Box.
Fig. 1
Fig. 2
FIXTURE WIRES
SMOOTH (BLACK)
JUNCTION BOX
(CEILING)
RIBBED (WHITE)
BARE COPPER
(Ground)
A
B
D
C
E
F
G
H
CHAIN
L
J
HOUSE WIRES
BLACK
WHITE
GREEN
(Ground)
FINISHING THE INSTALLATION
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) onto the Canopy
Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...