Page 1
PARTS & ASSEMBLY SHEET
Fixture Name: Cerchi 1030-363 CH
This fixture assembled PO:__________ Date: ________
Notice: Please review the parts listing and check for all parts before assembling the fixture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for replacement
parts.
PARTS LIST
Canopy
Chain 12ft Wire Connectors 3ea Spring Washer 1ea
Chain connector
Mounting Strap 1ea Hex Nut 3ea
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad finish)
Comments
1ea
2ea
Company Name:_______________________Co. Account #:_____________
to be filled out by retailer
Mounting Screws 2ea Top loop 1ea
Canopy Loop
with Collar
1ea Nipple 1ea
Green Ground
Screw
1ea
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet before
assembling the fixture.
1030-363 CH
ASSEMBLING THE FIXTURE (Fig.1)
1. Grasp the fixture wires and align the Center column
Nipple (M) to Fixture coupler (I) and thread Center
column(M) to Fixture coupler (I) until tight. Ensure the
fixture wires are not pinched in the coupler.
2. Gently spread the arms until evenly spaced if arms
are packed closed.
3. The Center column rings may be turned to your
desired angle.
NOTE: INSTALL THE GLASS ASSEMBLY AFTER
THE FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig 1
Page 2
A
PARTS & ASSEMBLY SHEET
Fixture Name: Cerchi 1030-363 CH
SSEMBLING THE FIXTURE (Fig.2)
4. Feed the fixture wires through the Top loop (D2) and pull
the wires until taut. Then screw the Top Loop（D2） to the
coupling on the top of fixture (D) until tight.
5. By measuring determine correct number of links needed
for proper hanging height. Use a pair of pliers to open one
link of the Chain (C2) then remove the excess Chain (C2)
and discard it.
6. Use one chain connector (E2) to attach one end of the
chain to the Top loop (D2) and close the chain connector.
7. Feed the fixture wires through the Chain (every three
links) and pull the wires until taut.
8. Slip Canopy loop collar (B2) over the chain, then do the
same with the canopy (F2).
9. When ready to complete the installation Use the other
chain connector and attach the other end of the chain to the
Fig 2
canopy loop (A2) and close the chain connector.
10. Feed the fixture wires through canopy loop (F) and
nipple(C) and pull until taut.
* You may now install the fixture.
Note: Complete these remaining steps after the fixture is
hung.
11. Place the Glass Shades(P) over the Threaded Sockets
(Q), secure with Socket washer (O) and by threading the
Socket Rings(N) until tight.
12. Install the light bulbs in accordance with the fixture's
specifications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING)
For Customer Service, contact the place of purchase to arrange for replacement parts.
Fig 3
Page 3
INSTALLATION INSTRUCTIONS
Fixture Name: Cerchi 1030-6, 9, 363, 3P, D5, M1L CH
For Chandelier Light Fixture
WARNING ! SHUT OFF POWER AT FUSE OR CIRCUIT BREAKER.
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton and the yellow
bag that holds all parts. Check that all parts are included as
shown in the illustration and parts list.
2. Shut off the power at the circuit breaker and remove old fixture
from ceiling, including the old mounting strap.
3. Thread Nipple (C) into Canopy Loop (F) until snug.
4. Thread other end of the Nipple (C) with Canopy Loop attached
into Mounting Strap (D).
5. Place Lock Washer (B) over end of Nipple (C) protruding
through Mounting Strap (D) and thread Hex Nuts (A) onto Nipple
until tight.
6. Take this mounting strap assembly and mount to ceiling
junction box with junction box Screws (E). Tighten screw securely
with screw driver.
7. Unscrew the Canopy loop collar (H) from the Canopy loop.
Take the canopy and pass over the Canopy loop. approximatly
one half of the canopy loop exterior threads should be exposed.
Adjust until desired height is reached. *the Canopy loop collar
should fit snugly on the Canopy loop after the canopy is installed.
Remove Canopy and Canopy lock collar.
8. Assemble the fixture and have an assistant or secure support
hold the weight of the fixture while you complete the wiring
connections.
9. Thread the fixture wires and ground wire of the assembled
fixture through the canopy loop and nipple and into the outlet box.
CONNECTING THE WIRES (Fig 2)
10. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE (or RIBBED).
11. Attach the GROUND wire(GREEN or COPPER) from the
Junction Box and the fixture Ground wire to the green Ground
Screw on the Mounting Bracket (B) or connect both wires
together using the correct size of wire connectors.
NOTE: Twist the wires together in the same direction you twist
the wire connector onto the wires.
12. Tuck these wire connections neatly into the Junction Box.
Fig. 1
JUNCTION BOX
(CEILING)
A
B
D
C
E
F
G
H
CHAIN
L
J
Fig. 2
13. Raise Canopy (G) to the ceiling and secure in place by
tightening the Canopy loop collar(H) into the Canopy Loop(F)
14. Install the light bulbs and glass shade as per the fixture
assembly sheet.
For Customer Service, contact the place of purchase to arrange for replacement parts.
YOUR INSTALLATION IS NOW COMPLETE.
RETURN POWER TO THE JUNCTION BOX AND
TEST THE FIXTURE.
Loading...