Product Name : Transmitter
Models : TE-310
GOLD APOLLO CO., LTD.
Rm 1, 3th F1.,No .77, Secretary. 1 , Hsin Tai Wu .,Rd.,
Hsi-Chih Hsien, Taiwan, R. O. C.
Tel : 886-2-2698-8888
Web site : http\\www.apollo.com
Models : TE-310 16KEY Transmitter
VHF UHF Transmitter
A
tt
en
t
io
n
TE-310 Transmitter is used to page guests or staffs in a limited area,
especially suitable for factory, restaurant and hospital. The operation
is simple and friendly to keep good communication with your guests
and staffs.
There are 19 push buttons for your choice. Each button is able
to independently page a single person and also available to
page more than one person at the same time, as well. In
addition, it has the flash light as a reminder and also can repeat
paging the guests/staffs automatically when the one you page
has not shown up.
Transmitter
Be aware at following situations ,which will help to extend the life
cycle of transmitter.
N Don't change transmitter or tamper with its original
appearance.
N Don't put transmitter close to a heat source or in light
direct sun.
N Don't put transmitter in dust , moisture or on uneven surface.
N Don't soak transmitter into the water.
N Never operate the device with out the correct Gold Apollo
antenna , or a suitable artificial load , connected.
Function \ Location
Function \ Location
PWRTX
F3F2F1
1 9
102
3 11
12
4
5
13
6 14
15
7
8 16
1. Antenna Connect (BNC 50 ohm)
2. Power Connect (8.4V/1.5A)
3. RS232 D-SUB (FEMALE 9PIN)
1
2
3
Outlook
2.PWR(Orange) Power LED
1.TX (Rad) Transmit LED
1 2
4
4. RJ-11 Telephone Jack To Cancer
parer.
1. Frequency range : 147~170MHz,
450~470MHz.
2. Modulation Type : F S K
3. Channel spacing : 12.5 / 25MHz
4. Output power (ERP): 1W
5. Maximum deviation: +/-4.5KHz
6. Harmonic Radiation : less - 25dBm
7. Frequency stability : 2.5ppm at -10C~60C
8. Output Connect : BNC (F)
9. Current Consumption :
Standby : 100mA ; Transmit : 400mA
7. Dimensions : 23.2 (W)*50 (H)*17(D)
8. Weight : 650g ( No Antenna )
Sy
st
e
m
S
pe
c
ifi
c
a
ti
on
s
Sy
ste
m
Sp
ec
ificat
ions
25
Ope
r
a
ti
o
n
INST
RU
CT
IO
N FO
R
OPE
RA
TIO
N:
1.Activate paging:
Press any button among these 50 push buttons, the light will flash
and enter active mode, then send the signal out.
u To repeat paging : In the active mode, it can be programmed to
send the same message every 30 sec. or 45 sec, or 60 sec, or 2
minutes, or 5 minutes or continuo
v To page more than one person :
More than one button can be activated at the same time to page
more than one person.
w LED Sign Display:
It's an option on the software.
When the button is pressed, it will activate to send the signal
and show the number on the LED Display at the same time.
The numbers on the Display will be arranged by sequence, the
first number always shows up firstly. , 30 minutes ,
Con
tr
o
l
b
ut
ton
s
2. Stop paging:
In the active mode or Time out mode, pressing the same
button again to stop paging, at the same time the repeating
and the number on the LED sign will be cancelled.
3. "Time out" Message display:
Once the option of "Time Out " message display is enable,
the button will be flash after being pressed for a certain time,
and will also send the message to the assigned location or
person as a reminder
4. Heart Beat ( anti-theft):
After activate the option of " heart beat ", the transmitter will
send heart beat signal every 15 sec, 30 sec, 45 sec, 1 minute, 2
minutes, 4 minutes or 6 minutes. The time-gap is programmable.
Op
e
ratio
n
1. Active mode: when the button is pressed , the light will be
turned on to enter the active mode, then the signal will be sent
and repeated, as well.
2. Stop mode: Re-pressing the button to turn off the light
represented " Stop mode ". Under the active mode or "Time Out
" mode, to press the button again can also enter stop mode.
3. Time Out mode: After repeating paging for a certain time,
the light of button will be flashing, then go to Time out mode,
Instruction for Flash Light:
Instruction for Flash Light
1. Activate screen: to set up basic configurations , such
as cap code and frequency from button No. 1 to button
No. 19
Instruc
tion for progra
mming:
Ins
t
r
uc
t
i
on
f
o
r p
ro
g
ra
m
m
ing
I
nstr
uct
i
on
fo
r
pr
og
r
am
m
in
g
2. To set up the cap codes and type from button No.
F1,F2,F3 . butt Please be sure to click " Canned " first to
type the content of message.
3.Config :
In
s
t
ru
c
tio
n f
or
p
rogra
mmi
ng
ΠTIME OUT LED OFF : to enable this option, when it's time
out for a certain number, it will enter off mode after the
time out message is sent if there is a message
preprogrammed.
• BEEP OFF : to enable this option, this button has no beep
sound
Ž Time Out : to enable this option represent the button has
been pressed for a certain time and not been delete yet,
the light of button can be flash or send out the message to
an assigned location or person as reminder. It can be
programmable for 5 min, 10 min, 15 min, 30 min, or
disable.
3. Configuration Instruction:
Instru
c
t
io
n
f
o
r pro
g
ra
mm
i
ng
• TX Repeat time : to set up time-gap for repeating page
before Time out , it can be programmable for 30sec
retary , 45 sec, 60 sec, 2 min, 5 min or disable
• LED Msg, enable : to enable this option, the number you press
will be shown on the LED display.
‘ LED SIGN CAPCODE: to set up the cap code of LED sign
display
’ Head of LED Sign massage : the title displayed on the LED
Sign
“ Timeout Msg. Enabl: to enable this option, the
preprogrammed message will be sent out when it's time up
” Head of Timeout message: the title displayed before the
Time out message.
Inst
ru
c
t
io
n
f
o
r pro
gra
mmi
ng
4. Write: please see the above
In the main menu of the window to execute
the command of " To flash\Write" for programming
5. Read: please see the above
in the main menu of the window to execute the
command of "To Flash\Read" to read the data.
Ins
t
ru
c
t
io
n
f
o
r
pro
gra
mmi
ng
Loading...