GoGo gate GGG2 TWS User Manual

WIRELESS DOOR SENSOR INSTALLATION GUIDE

Read instructions carefully before beginning

Please make sure your garage door is closed before you start installation.

The GoGogate product and our wireless door sensors are meant to be used with garage

door openers equiped with photo-eye safety sensors (manufactured after 1993). These

sensors are normally found at the bottom of your garage door and avoid accidental closing

of your garage door if an object or person is on the path of the door.

Step 1 Step 2

ID:1234

TO PREVENT SERIOUS INJURY OR DEATH FROM
MOVING GARAGE DOORS OR GATES:

- DO NOT let children use the GOGOGATE product and app without adult supervision.

- ONLY Operate your GOGOGATE device when you are in clear view of your garage

or gate and you have veried that there are no objects obstructing the operation of

the door. ALWAYS wait for garage door or gate to be completely closed.

- NEVER operate the remote access feature of your GoGoGate without ensuring that

there is an adult physically present in front of the door or gate validating that it is safe

to start the remote operation of your device

SIDE VIEW BACK VIEWBACK VIEWBACK VIEW FRONT VIEW

Open the sensor’s batteries’ compartment
to include the provided AAA batteries (x2).
Place the batteries as per picture indications.
Finally, close the compartment.

Step 3

Attach your wireless sensors to your garage door as per drawing below.

ID:1234

Place the sensors on the upper part of your garage door wall.

27 mm width

Note: write down and store in
a safe location the 4 digit code
located on the front of your sensor.

ID:1234

70 mm

Lenght

Make sure you place the sensor
with the “TOP” label facing

the garage door ceiling.

PLACE THE SENSOR IN THE UPPER PART OF YOUR GARAGE WITH

RED LED LIGHT FACING DOWN. (LEFT OR RIGHT SIDE)

Main sensor’s features:

• Remotely monitor if garage door is open or closed

• Check garage door temperature in ºC/ºF

• Receive real time alerts on your Smartphone

• Easy to install tilt sensor with double sided tapes

• Tilt switch broken when garage door opens.

• Monitor sensor’s battery status for prompt replacement

• Keep track of all garage door events in a built-in calendar of events

Place on the wall

with the double-sided

fastening strip.

ID:1234

GGG2-TWS-001SPECS

Frequency

Range

Operating Temperature

Battery type

2.4 Ghz

50 m or 150 ft (open space)

Between -10ºC and 70ºC

AAA (x2)

24 mm

Height

Battery life span

Packaging

Certication

1.5 years

Clamshell

CE - FCC

Regulatory notices

REMSOL has not approved any changes or modications to this device by the user. Any changes or modications could
void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

This device complies with FCCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC
radio frequency (RF) Exposure Guidelines. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guar­antee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

Download our user manual in our website www.gogogate.com or contact us at: [e-mail]

Still having issues. No problem.