GO Elliptical T-300MX, T-700MX User Manual
- 1 -
USER’S MANUAL
T-300MX / T-700MX
USER WEIGHT LIMITATION: 300lbs(136kgs).
SERIAL NUMBER (found on frame):
USA
Dear User,
For Customer Service
1-267-808-3999
Email: cs@go-elliptical.com
- 2 -
Your GO Elliptical machine - Each machine shipped in Two Boxes Carton No. 1 is the main machine body and
Carton No. 2 is the Per-assembled top post with the whole VST (Variable Stride length system)
Pre-assembled, machine now will be very easy and simple to put together Suggest you get a second partner to
assemble the machine together We are sure you will be able to put the machine together with ease and enjoy The
new World-wide Real VST unit with us.
Read the manual and there is no need to assemble any of the VST Part by you any longer!!
- 3 -
PREASSEMBLY
For future service or related questions:
Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your item.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________
Open the boxes:
You are now ready to open the boxes of your new equipment. Make sure to inventory all of the parts that are included in the boxes.
Check the Parts List for a full count of the number of parts included for this product to be assembled properly. .
Gather your tools:
Before starting the assembly of your unit, make sure that you have gathered all the necessary tools you may require to assemble the
unit properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.
Clear your work area:
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is free from
anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a comfortable amount of free
area around the unit for unobstructed operation.
Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another person when
assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 300lbs. it is not recommended that you use this
product. Serious injury may occur if the user’s weight exceeds the limit shown here. This product is not intended to support users
whose weight exceeds this limit.
For Customer Service
1-267-808-3999
Email: cs@go-elliptical.com
- 4 -
POWER REQUIREMENTS
Power Requirements:
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE
PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT
THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and
noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of
treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a
UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an
electrical rating 120VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric
current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding
conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing below.
GFCI outlets and GFCI / AFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI / AFCI Circuit Breakers may cause this
equipment to function improperly.
- 5 -
SUPPLIED COMPONENTS BOX 1
Hardwar box
Base Frame
Console
Rear Stabilizer
Front Stabilizer
Fixed Handlebar
Action Handlebar (R)
Action Handlebar (L)
Power pack
Action Arm Cover Front
Pedal Support Tube Top (L/R)
Pedal Support Tube Bottom (L/R)
Action Arm Cover Rear
Pedal Tube Cover
Top L/R
Pedal Tube Cover
Bottom L/R
Water Bottle Holder
Console Base Cover Rear
- 6 -
SUPPLIED COMPONENTS BOX 2
Pedal Support Tube (L)
Upright Tube
Pedal (L)
Pedal (R)
Pedal Support Tube (R)
Pedal Support Tube (L)
Pedal Support Tube (R)
Console Base
Upright Post Cover (L)
Upright Post Cover (R)
Fan/VST Board
- 7 -
TOOL included with machine:
General tools prepared by user:
MILLIMETERS
M8 socket
M8/M10
wrench
Screw driver 5mm
M8 wrench
M10 wrench
Screw driver 5mm
- 8 -
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
1
Handlebar end cap
2
CE55-1
2
Handlebar grip
2
CE55-2
3
T-Bar grip
2
CE55-3
4
Hand pulse grip unit
2
CE55-4
5
End cap 4 CE55-5
6
Screw M8*1.25*15
2
CE55-6
7
Locking washer
2
CE55-7
8
Washer ∮25.4
2
CE55-8
9
Sleeve O.D. 25.4MM
4
CE55-9
10
Sleeve 8 CE55-10
11
Washer 10*32*2T
6
CE55-11
12
Nylock nut M10*1.5
9
CE55-12
13
Pedal tube shaft ∮17*70mm
2
CE55-13
14
Pedal tube shaft ∮17*97mm
2
CE55-14
15
Bearing 2203RS
4
CE55-15
16
Retainer R40
4
CE55-16
17
Washer 10*22*3T
2
CE55-17
18
Allen head bolt M8*1.25*15
38
CE55-18
19
Screw M8*1.25*65
4
CE55-19
20
Nylock nut M8*1.25
10
CE55-20
21
Plastic cap 5/16
4
CE55-21
22
Large square plastic cap
2
CE55-22
23
Rear foot cover
2
CE55-23
24
Front foot cover (middle)
2
CE55-24
25
Left roller holder
1
CE55-25
26
Right roller holder
1
CE55-26
27
Wheel 2 CE55-27
28
Screw M8*50
2
CE55-28
29
Screw M4*16mm
6
CE55-29
30
Screw M5*0.8*12
16
CE55-30
31
Screw M5*20
29
CE55-31
32
Screw M4*8
8
CE55-32
33
Bearing 6003
2
CE55-33
34
Bearing ∮17mm
4
CE55-34
35
Screw M6*15
1
CE55-35
36
Locking screw M8*1.25*30
1
CE55-36
- 9 -
37
Spacer 17*28*1.0
8
CE55-37
38
Screw M8*1.25*65
6
CE55-38
39
Washer 8*25mm
20
CE55-39
40
Screw M8*1.25*30
1
CE55-40
41
Nut M8 3 CE55-41
42
Spring 3.5mm*21mm
1
CE55-42
43
Console 1 CE55-43
44
P.U.Roller
2
CE55-44
45
Screw M5*15
4
CE55-45
46
Plastic flat round cap
2
CE55-46
47
Flywheel 250
1
CE55-47
48
Speed Sensor Cable
1
CE55-48
49
Belt 550 J6
1
CE55-49
50
End cap 2 CE55-50
51
Plastic flat round cap
2
CE55-51
52
Pedal, LH
1
CE55-52
53
Pedal, RH
1
CE55-53
54
Adjustable foot
2
CE55-54
55
Small square plastic cap
2
CE55-55
56
End cap (T-Bar)
2
CE55-56
57
Middle cover, LH
1
CE55-57
58
Middle cover, RH
1
CE55-58
59
Side cover, LH
1
CE55-59
60
Side cover, RH
1
CE55-60
61
Screw M3*10mm
1
CE55-61
62
Motor 1 CE55-62
63
D- Axle ∮15**182mm
1
CE55-63
64
Magnet ∮14.8*7L
1
CE55-64
65
Washer 5/16*16*1.0
4
CE55-65
66
Pulley 2 CE55-66
67
Base frame
1
CE55-67
68
Upright tube
1
CE55-68
69
Swivel tube, LH
1
CE55-69
70
Swivel tube, RH
1
CE55-70
71
Fixed handle bar
1
CE55-71
72
Handle bar, LH
1
CE55-72
73
Handle bar, RH
1
CE55-73
74
Square pedal tube, left
1
CE55-74
75
Square pedal tube, right
1
CE55-75
76
Front foot ( Stabilizer )
1
CE55-76
77
Rear foot ( Stabilizer )
1
CE55-77
78
Flywheel holder bracket
1
CE55-78
79
Belt tensioner
1
CE55-79
80
Metal cross, LH
1
CE55-80
81
Metal cross, RH
1
CE55-81
- 10 -
82
Bushing 2 CE55-82
83
Bushing 2 CE55-83
84
Metal plate
2
CE55-84
85
Roller axle ∮12**103mm
2
CE55-85
86
Connecting tube
2
CE55-86
87
Front cover, LH
1
CE55-87
88
Front cover, RH
1
CE55-88
89
Console cable 990MM
1
CE55-89
90
Cable 850MM
1
CE55-90
91
Power wire 750MM
1
CE55-91
92
Power ADAPTOR
1
CE55-92
93
Washer ∮17*∮12*Ｔ1.0
3
CE55-93
94
Washer ∮35*∮12*Ｔ2.0
1
CE55-94
95
Washer ∮35*∮6*Ｔ2.0
1
CE55-95
96
Bearing 6001
6
CE55-96
97A
Toggle switch left
1
CE55-97A
97B
Toggle switch right
1
CE55-97B
98
Square moving arms (L)
1
CE55-98
99
Square moving arms (R)
1
CE55-99
100
Long connecting bar
2
CE55-100
101
Swinging axle plate
2
CE55-101
102
Second step tube left
1
CE55-102
103
Second step tube right
1
CE55-103
104
Step foot cover-Top
2
CE55-104
105
Step foot cover-Bottom
2
CE55-105
106
Pedal tube cover top (L)
1
CE55-106
107
Pedal tube cover bottom ( L )
1
CE55-107
108
Pedal tube cover top ( R )
1
CE55-108
109
Pedal tube cover bottom ( R )
1
CE55-109
110
Roller cover
2
CE55-110
111
Screw M5*8
3
CE55-111
112
Bearing 6002
4
CE55-112
113
Alum rail
2
CE55-113
114
Axle for inner adjustor
1
CE55-114
115
Base for inner adjustor
1
CE55-115
116
Outer adjustor
1
CE55-116
117
Connecting axle for lift motor
1
CE55-117
118
Holder for lift motor
2
CE55-118
119
Adjustor connector
2
CE55-119
120
Hex head screw M10×70mm
1
CE55-120
121
Lift motor
1
CE55-121
122
Screw M4*16
24
CE55-122
123
Arm cover front
2
CE55-123
124
Arm cover rear
2
CE55-124
125
Base bracket for lift motor
1
CE55-125
- 11 -
126
Hex head screw M10×40mm
1
CE55-126
127
Bottle holder
1
CE55-127
128
VST control board
1
CE55-128
129
380 Pulley rim
2
CE55-129
130A
Upright post cover
1
CE55-130A
130B
Upright post cover
1
CE55-130B
131
Console base
1
CE55-131
132A
Left upper upright post cover
1
CE55-132A
132B
Right upper upright post cover
1
CE55-132B
133
Front console cover
1
CE55-133
134
Front cover
1
CE55-134
135
Screw M4*16mm
11
CE55-135
136
Screw M4*16mm
8
CE55-136
137
Adjustor end cap
2
CE55-137
138
Large adjustor screw M10
2
CE55-138
139
Fan network
1
CE55-139
140
FAN 1 CE55-140
141
Cable for Fan
1
CE55-141
142
Fan and VST control board
1
CE55-142
143
Inner small handlebar
2
CE55-143
144A
Handlebar cover front
2
CE55-144A
144B
Handlebar cover rear
2
CE55-144B
145
Rear console base cover
1
CE55-145
146
Adjustor guide cover
2
CE55-146
147
Adjustor fixed cover
2
CE55-147
148
Adjustor rod cover
8
CE55-148
149
Tablet holder
1
CE55-149
#A
Washer M8
4
CE55-#A
- 12 -
ASSE
- 13 -
ASSEMBLY
STEP 1: Attach the Front Support (Front Stabilizer)
NOTE: To make attaching the support easier place a large
Styrofoam block under the machine.
(A) Attach the front support to the base frame with the wheels facing
outward.
(B) Align the 2 bolt holes in the front support with the bolt holes in the
main frame.
(C) Secure the front support to the main frame by using 2 x #19 bolts
inserted through the bottom, 2 x # 65 washers 2 x 20 lock nuts and
2 x #21 nut covers
(D) Tighten all bolts now.
#19
2
#65
2
#20
2
#21
2
Loading...