Godox X2TC, X2TN, X2TF, X2TS Instruction Manual

Page 1

深圳市神牛摄影器材有限公司

GODO X Photo Equipment Co., Ltd.

地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋1层至4层、4栋1层至4层 1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China

电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.com

705-X2TC00-00

Made In China

Instruction Manual

说明手册

TTL

无线引闪器

TTL Wireless Flash Trigger

Page 2

Contents

Foreword

Warning

Names of Parts

Body

LCD Panel

Battery

Installing Batteries

Battery Level Indication

Setting the Flash Trigger

Power Switch

Automatically Enter Power Saving Mode

Power Switch of AF Assist Beam

Channel Settings

Wireless ID Settings

Mode Settings

Output Value Settings

Flash Exposure Compensation Settings

Multi Flash Settings (Output Value, Times

and Frequency)

Modeling Lamp Settings

ZOOM Value Settings

Shutter Sync Settings

Buzz Settings

Foreword

Sync Socket Settings

SHOOT Function Settings

C.Fn: Setting Custom Functions

Using the Flash Trigger

As a Wireless Camera Flash Trigger

As a Wireless Outdoor Flash Trigger

As a Wireless Original Flash Trigger

As a Wireless Studio Flash Trigger

As a Wireless Shutter Release Trigger

As a Flash Trigger

with 3.5mm Sync Cord Jack

Connect to Smartphone through Bluetooth

Compatible Smartphone Models

Compatible Flash Models

Compatible Camera Models

Technical Data

Restore Factory Settings

Firmware Upgrade

Attentions

Caring for Flash Trigger

- 23 - - 24 -

Thanks for your purchase of this X2T-C wireless flash trigger.

This wireless flash trigger is suitable for using Canon cameras to control Godox

flashes with X system e.g. camera flash, outdoor flash, and studio flash. It can also

control Canon original speedlites with the coordination of X1R-C receiver. Featuring

multi-channel triggering, stable signal transmission, and sensitive reaction, it gives

photographers unparalleled flexibility and control over their strobist setups. The flash

trigger applies to hotshoe-mounted Canon EOS series cameras, as well as the

cameras which have PC sync sockets.

With X2T-C wireless flash trigger, high speed synchronization is available for most of

camera flashes in the market which support E-TTL I I. The max flash synchronization

speed is up to 1/8000s *.

*: 1/8000s is achievable when the camera has a max camera shutter speed of 1/8000s.

Page 3

Warning

Names of Parts

Do not disassemble. Should repairs become necessary, this product must be sent to

an authorized maintenance center.

Always keep this product dry. Do not use in rain or in damp conditions.

Keep out of reach of children.

Do not use the flash unit in the presence of flammable gas. In certain circumstance,

please pay attention to the relevant warnings. Do not leave or store the product if the ambient temperature reads over 50℃.

Turn off the flash trigger immediately in the event of malfunction.

Observe precautions when handling batteries

- Use only batteries listed in this manual. Do not use old and new batteries or

batteries of different types at the same time.

- Read and follow all warnings and instructions provided by the manufacturer.

- Batteries cannot be short-circuited or disassembled.

- Do not put batteries into a fire or apply direct heat to them.

- Do not attempt to insert batteries upside down or backwards.

- Batteries are prone to leakage when fully discharged. To avoid damage to the

product, be sure to remove batteries when the product is not used for a long time or

when batteries run out of charge.

- Should liquid from the batteries come into contact with skin or clothing, rinse

immediately with fresh water.

- 25 - - 26 -

Body

Mode Selection/Locking Button

Menu Button/ Modeling Lamp Control

ALL Settings Selection/ All Selection

Note: All the buttons have backlight, which is convenient for usage in dark environment.

Group Button A

Group Button B

Group Button C

Group Button D

Group Button E

TEST/Shutter Button

Type-C USB Port

3.5mm Sync Cord Jack

Hot Shoe Speedlite Connection

1/128

A B C

Hot Shoe Camera Connection

Status Indicator Lamp

--Green: Trigger (Flash) + Focus (Camera)

--Red: Trigger (Flash) + Shutter (Camera)

AF Assist Beam Switch

CH 01

--ON (AF Assist Beam outputs)

AF-assist Lamp

--OFF (A F Assist Beam

do not output)

Power Switch

--ON (Power On)

--OFF (Power Off)

Battery Compartment

Select Dial

Page 4

Names of Parts

LCD Panel

1. Channel (32) 2. Camera Connection 3. Modeling Lamp Master Control

4. High-Speed/Rear Curtain Sync 5. Sound 6. Battery Level Indication

7. Group 8. Mode 9. Power 10. ZOO M Value 11. Version

8 9

1/128

A B C

Group Display

CH 01

5 3

- 27 - - 28 -

SYNC

BLUE.T.

BEEP ZOOM

V0.2

1/4

Battery

AA alkaline batteries are recommended.

114

Installing Batteries

As shown in the illustration, slide the battery compartment lid of the flash trigger and insert two AA batteries separately.

Battery Indication

Check the battery level indication on the LCD panel to see the remaining battery level during the usage.

Battery Level Indication

3 grids

2 grids

1 grid

Blank grid

Blinking

The battery indication only refers to AA alkaline batteries. As the voltage of Ni-MH battery tends to be low, please do not refer to this chart.

Meaning

Full

Middle

Low

Low battery, please replace it.

< 2.5V The battery level is going

to be used out immediately (please

replace new batteries, as low power

leads to no flash or flash missing in

case of long distance).

Page 5

Setting the Flash Trigger

Power Switch

Slide the Power Switch to ON, and the device is on and status indicator lamp will not reveal.

Note: In order to avoid power consumption, turn off the transmitter when not in use.

Automatically Enter Power Saving Mode

1. The system will automatically enter standby mode after stop operating the

transmitter over 60 seconds. And the displays on the LCD panel disappear now.

2. Press any button to wake up. If the flash trigger is attached to the hot shoe of

CAN ON EOS camera, half press the camera shutter can also wake the system up.

Note: If do not want to enter power saving mode, press the <MENU > button to enter C.Fn custom

settings and set STBY to OFF.

Power Switch of AF Assist Beam

Slide the AF-assist beam switch to ON, and the AF lighting is allowed to output.

When the camera cannot focus, the AF assist beam will turn on; when the camera can

focus, the AF assist beam will turn off.

Channel Setting

1. Short press the <MEN U> button and choose CH to set the channel value.

2. Turn the select dial to choose the appropriate channel. The channel value will be

confirmed after exiting the menu.

3. This flash trigger contains 32 channels which can be changed from 1 to 32. Set the

transmitter and the receiver to the same channel before usage.

Wireless ID Settings

Change the wireless channels and wireless ID to avoid interference for it can only be triggered after the wireless IDs and channels of the master unit and the slave unit are set to the same.

Press the <MEN U> button to enter C.Fn ID. Press the <SET> button to choose O FF channel expansion shutdown, and choose any figure from 01 to 99.

Note: It can only be used when the slave units have the wireless ID settings functions. If they do not have, please set the ID to OF F.

Mode Setting

1. After pressing the group button to select one

group, press the <MOD E> button and all the current group’s mode will be changed by the order of

TTL/M/--.

2. In normal situation, press the <MOD E> button to

switch the multi-group mode to MULTI mode. Press the group selection button and then press the <MOD E> buttoncan set the MULTI mode to ON or

OFF.

- 30 -- 29 -

1/128

A B C

1/128

1Hz

B C

1Times

CH 01

Page 6

Setting the Flash Trigger

Output Value Settings

In the M mode

1 . Press the group button to choose the group, turn the select dial, and the power

output value will change from Min to 1/1 in 0.3 stop increments. Press the <SET>

button to confirm the setting.

2. Press <ALL> button to choose all groups’ power output value, turn the select dial,

and all groups’ power output value will change from Min to 1/1 in 0.3 stop

increments. Press <ALL> button again to confirm the setting.

Note: Min. refers to the minimum value that can be set in M or Multi mode. The minimum value can be

set to 1/128 0.3, 1/256 0.3, 1/128 0.1, 1/256 0.1, 3.0(0.1) and 2.0(0.1) according to C.Fn-Min.

For most of camera flashes, the minimum output value is 1/128 and cannot be set to 1/256. However,

the value can change to 1/256 when using in combination with Godox strong power flashes e.g. AD600,

etc.

Flash Exposure Compensation Settings

In the TTL mode

Press the group button to choose the group, turn the select dial, and the FEC value will

change from -3 to ~3 in 0.3 stop increments. Press the <SET> button to confirm the

setting.

Multi Flash Settings (Output Value, Times and Frequency)

1. In the multi flash (TTL and M icon are not

displayed).

2. The three lines are separately displayed as power

output value, Hz(flash frequency) and Times(flash

times).

3. Press the <SET> button and turn the Select Dial to

change the power output value from Min. to 1/4 in

integer stops.

4. Press the <SET> button again and choose Hz to

change flash frequency. Turn the select dial to

change the setting value.

5. Press the <SET> button again and choose Times to

change flash times. Turn the select dial to change

the setting value.

6. Until all the amounts are set. Or during any value

setting, short press the <SET> button to exit the

setting status.

7. In the multi flash setting submenu, short press the

<MOD E> button to return to main menu when no

values are blinking.

Note: As flash times are restricted by flash output value and flash frequency, the flash times cannot

surpass the upper value that permitted by the system. The times that transported to the receiver end are

a real flash time, which is also related to the camera’s shutter setting.

- 32 -- 31 -

1/128

1Hz

B C

1Times

CH 01

Page 7

Setting the Flash Trigger

Modeling Lamp Settings

1. Long press the <MEN U> button for 2 seconds to

control the ON/O FF of the modeling lamp.

ZOOM Value Settings

Short press the <MEN U> button to enter the ZOOM

menu. Short press the <SET> button and turn the

select dial, and the ZOO M value will change from

AUTO/24 to 200. Choose the desired value and back

to the main menu.

Note: The flash’s ZOOM should be set to Auto (A) mode before

responding.

Shutter Sync Settings

1. High-speed sync: short press the <MEN U>

button to enter the SYN C menu. Choose high-speed

sync icon and is displayed on the LCD panel.

2. Second-curtain sync: short press the <MEN U>

button to enter the SYN C menu. Choose second-

curtain sync icon and is displayed on the LCD

panel.

SYNC

BLUE.T.

BEEP

ZOOM

SYNC

BLUE.T.

BEEP ZOOM

V0.2

1/4

V0.2

1/4

Buzz Settings

Press the <MEN U> button to enter C.Fn BEEP and

press the <SET> button. Choose ON to turn on the

BEEP while OFF to turn off it. Press the <M ENU>

button again to back to the main menu.

Sync Socket Settings

1. Press the <MEN U> button to enter C.Fn SYNC

and press the <SET> button to choose IN or OUT.

Press the <MEN U> button again to back to the

main menu.

1.1 When choosing IN, this sync socket will

enable X2T-C to trigger flash.

1.2 When choosing OUT, this sync socket will

send trigger signals to trigger other remote

control and flash.

- 34 -- 33 -

SYNC

BLUE.T.

BEEP

ZOOM

SCAN

PC SYNC

OFF ON

IN OUT

V0.2

1/4

V0.2

2/4

Page 8

Setting the Flash Trigger

SHOOT Function Settings

Press the <MEN U> button to enter C.Fn SHOOT.

Press the <SET> button to choose one-shoot or multi-

shoots, and press the <MEN U> button again to back

to the main menu.

One-shoot: When shooting, choose one-shoot. In the

M and Multi mode, the master unit only sends

triggering signals to the slave unit, which is suitable

for one person photography for the advantage of

power saving.

Multi-shoots: When shooting, choose multi-shoots,

and the master unit will send parameters and

triggering signals to the slave unit, which is suitable

for multi person photography. However, this

function consumes power quickly.

APP: Only send triggering signal when camera is

shooting (control the flash's parameters by

smartphone APP).

DELAY

SHOOT

DIST

STEP APP

V0.2

3/4

C.Fn: Setting Custom Functions

The following table lists the available and unavailable custom functions of this flash.

Custom Function

SYNC

BLUE.T.

BEEP

ZOOM SCAN

CH ID

PC SYNC

DELAY

SHOOT

DIST

Function

Shutter sync setting

Bluetooth status setting Beeper

ZOOM setting Scan the spare channel Wireless Channel setting Wireless ID

Sync cord jack

Delay setting

APP

Triggering distance

Setting Signs

OFF ON ON OFF 24 OFF START 01 OFF 01-99

IN OUT OFF

0.1ms-9.9ms One-shoot

All-shoot

APP

0-30m 1-100m

Settings and Description

Front curtain High speed Second curtain Off On On Off AUTO/24-200 Off Start to find the spare channel 01-32 Off Choose any figure from 01-99 (the old version flashes cannot use this function temporarily) Trigger X2T-C to fire flash Output signal to trigger other remote control and flash Off Set the firing delay in high-speed sync Only send triggering signals in the M & Multi mode when camera is shooting Send parameters and triggering signal when camera is shooting(suitable for multi person photography) Only send triggering signal when camera is shooting (control the flash’s parameters by smartphone APP) 0-30m triggering 1-100m triggering

- 36 -- 35 -

Page 9

Setting the Flash Trigger

Using the Flash Trigger

Custom Function

STEP

GROUP

STBY

LIGHT

LCD

Function

Power output value

Group

Sleep

Backlighting time

Contrast ratio of LCD panel

Setting Signs

1/128(0.3) 1/256(0.3) 1/128(0.1) 1/256(0.1)

3.0(0.1)

2.0(0.1) 5 (A-E) 3 (A-C) 60sec 30min 60min OFF 12sec OFF ON

-3-+3

Settings and Description

The minimum output is 1/128(change in 0.3 step) The minimum output is 1/256(change in 0.3 step) The minimum output is 1/128(change in 0.1 step) The minimum output is 1/256(change in 0.1 step) The minimum output is 3.0(change in 0.1 step) The minimum output is 2.0(change in 0.1 step) 5 groups(A/B/C/D/E) 3 groups(A/B/C) 60 seconds 30 minutes 60 minutes

-Auto off in 12 seconds Always off Always lighting The contrast ration can be set as integral number from

-3 to +3

Using the Flash Trigger

1. As a Wireless Camera Flash Trigger

Take TT685C as an example:

1.1 Turn off the camera and mount the transmitter

on camera hotshoe. Then, power on the flash trigger and the camera.

SCAN

PC SYNC

1.2 Short press the <MEN U> button to set channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”).

1.3 Turn on the camera flash, press the

wireless setting button and the wireless icon and <SLAVE> slave unit icon will be displayed on the LCD panel. Press the < CH> button to set the same channel to the flash trigger, and press the <Gr> button to set the same group to the flash trigger (Note: please refer

to the relevant instruction manual when setting the camera flashes of other models).

1.4 Press the camera shutter to trigger and the status lamp of the flash trigger turns red synchronously.

2. As a Wireless Outdoor Flash Trigger

Take AD600B as an example:

2.1 Turn off the camera and mount the

transmitter on camera hotshoe. Then,

power on the flash trigger and the

V0.2

2/4

camera.

2.2 Short press the <MEN U> button to set

channel, group, mode and parameters

(refers to the contents of “Setting the

Flash Trigger”).

2.3 Power on the outdoor flash and press the wireless setting button and the

wireless icon will be displayed on the LCD panel. Long press the

< >

- 38 -- 37 -

< >

CH19

Zm/C.Fn Gr CH

< >

SLAVE

Zoom

1/128

Page 10

Using the Flash Trigger

<GR/C H> button to set the same channel to the flash trigger, and short press

the < GR/C H> button to set the same group to the flash trigger (Note: please

refer to the relevant instruction manual when setting the oudoor flashes of other

models).

2.4 Press the camera shutter to trigger and the status lamp of the flash trigger turns

red synchronously.

3. As a Wireless Original Flash Trigger

Take 600EX-RT as an example:

3.1 Turn off the camera and mount the transmitter

on camera hotshoe. Then, power on the flash

trigger and the camera.

3.2 Short press the <MEN U> button to set channel,

group, mode and parameters (refers to the

contents of “Setting the Flash Trigger”).

3.3 Attach the original flash to the X1R-C receiver.

Press the <CH> button on the receiver to set

the same channel to the flash trigger, and press

the <Gr> button to set the same group to the

flash trigger (Note: please refer to the relevant

instruction manual when setting the original

camera flashes).

3.4 Press the camera shutter to trigger. And the

status lamp of the camera flash and the flash

trigger both turn red synchronously.

4. As a Wireless Studio Flash Trigger

Take GS400II as an example:

4.1 Turn off the camera and mount the transmitter

on camera hotshoe. Then, power on the flash trigger and the camera.

4.2 Short press the <MEN U> button to set

channel, group, mode and parameters (refers to the contents of “Setting the Flash Trigger”).

4.3 Connect the studio flash to power source and

power it on. Synchronously press down the <GR/C H> button and <S1/S2>button and the wireless icon will be displayed on the

< >

LCD panel. Long press the <G R/CH> button to set the same channel to the flash trigger, and short press the < GR/C H > button to set the same group to the flash trigger (Note: please refer to the relevant instruction manual when setting the studio flashes of other models).

4.4 Press the camera shutter to trigger. And the

status lamp of the camera flash and the flash trigger both turn red synchronously.

Note: As the studio flash’s minimum output value is

1/32, the output value of the flash trigger should be set to or over 1/32. As the studio flash do not have TTL and stroboscopic functions, the flash trigger should be set to M mode in triggering.

- 40 -- 39 -

Page 11

Using the Flash Trigger

5. As a Wireless Shutter Release Trigger

Operation method:

5.1 Turn off the camera. Take a camera remote

cable and insert one end into the camera’s

shutter socket and the other end to the

shutter release port of X1R-C to connect.

Power on the camera and the receiver.

5.2 Short press the <MEN U> button to set

channel, group, mode and parameters

(refers to the contents of “Setting the Flash

Trigger”).

5.3 Press the receiver’s <CH> button to set the

same channel to the flash trigger, and press

the <Gr> button to set the same group to the

flash trigger.

5.4 Half press the button to focus and full

press the <TES T> button to shoot. Release

the button until the status lamp turns to red.

6. As a Flash Trigger with 3.5mm Sync Cord Jack

Operation method:

6.1 The connection method please refers to the

contents of “As a Wireless Studio Flash Trigger”

and “As a Wireless Shutter Release”.

6.2 Set the transmitter end’s sync cord jack as an

output port. Operation: press the <MEN U>

button on the transmitter end to enter C.Fn

settings. Then, set PC SY NC to O UT mode.

6.3 Press the shutter normally and the flashes will

be controlled by sync cord jack's signal.

7. Connect to Smartphone through Bluetooth

Using method:

7.1 Short press the <MENU> Button to enter

BLUE.T. to open the Bluetooth. The Bluetooth ID

will displayed under the ON.

7.2 Search“Godox Photo”in iPhone’s APP Store

and download the APP. Or install the APP by

scanning the QR Code with your smartphone.

7.3 Open the APP and choose .

7.4 Connect the transmitter to the responded

Bluetooth ID and enter the password to

match(the initial password is “000000”).

- 42 -- 41 -

SYNC

BLUE.T.

BEEP ZOOM

OFF ON

GDBHA7BC

"GodoxPhoto"

V0.2

1/4

Page 12

Using the Flash Trigger

7.5 Full match and back to APP main interface.

7.6 When started the Bluetooth function, the

Bluetooth icon will be displayed on the

transmitter’s panel.

7.7 Set the channels of the slave flash and the

transmitter to the same, and parameters e.g.

slave flash mode, power value, modeling lamp

and beep can be controlled on the APP of the

smartphone.

7.8 Use the APP of the smartphone for shooting

after setting all the parameters.

Note: When successfully connected the flash trigger and

smartphone APP, the auto sleep of the flash trigger can be

set to 30 min.

Compatible Smartphone Models

This flash trigger can be used on the following Smartphone models:

iPhone 6S iPhone 6S Plus iPhone 7 Plus iPhone 7 iPhone 8 Plus

iPhone 8 iPhone 6 Plus iPhone 6 iPhone X

HUAWEI P9 HUAWEI P10 HUAWEI P10 Plus HUAWEI Mate 9 Pro

HUAWEI Mate 9 HUAWEI Mate 10 Pro HUAWEI Mate 10

HUAWEI P20 HUAWEI P20 Pro

Samsung galaxy S8 Samsung galaxy Note8 Samsung galaxy S9

1. This table only lists the tested Smartphone models, not all Smartphone. For the compatibility of other Smartphone models, a self-test is recommended.

2. Rights to modify this table are retained.

- 43 -

- 44 -

Page 13

Compatible Flash Models

Receiver

Transmitter

X2T-C

Note: The range of support functions: the functions that are both owned by X2T-C and flash.

Flash

AD600 series/AD400 series/AD360II series

AD200 series/V860II series/V850II

V350C/TT685 series/TT600/TT350C

QuickerII series/QTII/SK II series

DP II series/GSII

X1R-C

600EX-RT/580EXII/580EX/430EXII

V860C

XTR-16

AD360/AR400

Quicker series/SK series/DP series/

GT/GS series/Smart flash series

XTR-16S

V860C

V850

- 45 -

Note

As there are so many camera flashes in

the market which are compatible with

Canon speedlites, we do not test one by one.

The flashes with Godox wireless USB port

Can only be triggered

The relationship of XT wireless system and X2 wireless system:

XT-16

(Code Switch)

(Display Screen)

XT-16

(Code Switch)

(Display Screen)

ON ON ON ON ON ON ON

CH01 CH02 CH03 CH04 CH05 CH06 CH07 CH08

ON ON ON ON ON ON ON ON

CH09 CH10 CH11 CH12 CH13 CH14 CH15 CH16

Compatible Camera Models

This flash trigger can be used on the following Canon EOS series camera models:

1Dx Mark II 1Dx 5Ds/5Dsr 5DⅣ 5D Mark III 5D Mark II 5D

7D Mark II 7D 6D 80D 70D 60D 50D 6D MarkII 77D 800D

40D 30D 750D/760D 700D 650D 600D 550D500D 450D 400D

Digital350D DIGITAL100D 1200D 1000D 1100D M5 M3 EOS R

M50 1500D(2000D/T7) 3000D(4000D)

1. This table only lists the tested camera models, not all Canon EOS series cameras. For the compatibility of other camera models, a self-test is recommended.

2. Rights to modify this table are retained.

3. The cameras which are released before 2012 do not have TTL mode in their D and E group.

4. 1500D(2000D/T7), 3000D(4000D):When the high-speed shutter is higher than 1000, there will be

lunimance edge on the photo.

- 46 -

Page 14

Technical Data

Model

Compatible cameras

Compatible smartphone

(sync flash in M mode)

Power supply

Flash Exposure Control

TTL autoflash

Manual flash

Stroboscopic flash

Function

High-speed sync

Flash exposure

compensation

Flash exposure lock

Focus assist

Modeling lamp

Beeper

Wireless shutter

ZOOM setting

TCM function

Firmware upgrade

Memory function

X2T-C

Canon EOS cameras (E-TTL II autoflash)

Support for the cameras that have PC sync socket.

iphone, Huawei, Samsung(see the compatible smartphone models for details)

2*AA batteries

E-TTL II

Yes

Yes, ±3 stops in 1/3 stop increments

Yes

Control the beeper by the flash trigger The receiver end can control the

camera shooting through the 3.5mm sync cord jack

Adjust the ZOOM value by the transmitter

Transform the TTL shooting value into the output value in the M mode

Upgrade through the Type-C USB port

Settings will be stored 2 seconds after last operation and recover

after a restart

- 47 -

Model

Wireless Flash

Transmission range (approx.)

Built-in wireless

Modulation mode

Channel

Wireless ID

Group

Other

Display

Dimension/Weight

2.4G Wireless Frequency Range

Max. Transmitting Power of 2.4G Wireless

Restore Factory Settings

Hold the MOD E button and power the flash trigger on, and all the parameters will restore the factory settings.

X2T-C

0-100m

2.4G

MSK

01-99

Large LCD panel, backlighting O N or OFF

72x70x58mm/90g

2413.0MHz-2463.5MH z

5dbm

Firmware Upgrade

This flash trigger supports firmware upgrade through the Type-CUSB port. Update information will be released on our official website.

USB connection line is not included in this product. As the US B port is a Type-C USB socket, please use Type-C USB connection line.

As the firmware upgrade needs the support of Godox G3 software, please download and install the "Godox G3 firmware upgrade software" before upgrading. Then, choose the related firmware file.

- 48 -

Page 15

Attentions

1. Unable to trigger flash or camera shutter. Make sure batteries are installed correctly and Power Switch is turned on. Check if the transmitter and the receiver are set to the same channel, if the hotshoe mount or connection cable is well connected, or if the flash triggers are set to the correct mode.

2. Camera shoots but does not focus. Check if the focus mode of the camera or lens is set to MF. If so, set it to AF.

3. Signal disturbance or shooting interference. Change a different channel on the device.

4. Operating distance limited or flash missing. Check if batteries are exhausted. If so, change them.

The Reason & Solution of Not Triggering in Godox 2.4G Wireless

1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base station, 2.4G wifi router, Bluetooth, etc.)

→ To adjust the channel CH setting on the flash trigger (add 10+ channels) and

use the channel which is not disturbed. Or turn off the other 2.4G equipment in working.

2. Please make sure that whether the flash has finished its recycle or caught up with the continuous shooting speed or not(the flash ready indicator is lighten) and the flash is not under the state of over-heat protection or other abnormal situation.

→ Please downgrade the flash power output. If the flash is in TTL mode, please try

to change it to M mode(a preflash is needed in TTL mode).

3. Whether the distance between the flash trigger and the flash is too close or not

→ Please turn on the “close distance wireless mode” on the flash trigger (＜0.5m):

→ Please set the C.Fn-DIS T to 0-30m.

4. Whether the flash trigger and the receiver end equipment are in the low battery states or not

　 → Please replace the battery(the flash trigger is recommended to use 1.5V

disposable alkaline battery).

Caring for Flash Trigger

Avoid sudden drops. The device may fail to work after strong shocks, impacts, or excess stress. Keep dry. The product isn’t water-proof. Malfunction, rust, and corrosion may occur and go beyond repair if soaked in water or exposed to high humidity. Avoid sudden temperature changes. Condensation happens if sudden temperature changes such as the circumstance when taking the transceiver out of a building with higher temperature to outside in winter. Please put the transceiver in a handbag or plastic bag beforehand. Keep away from strong magnetic field. The strong static or magnetic field produced by devices such as radio transmitters leads to malfunction.

- 50 -- 49 -

Page 16

FCC Statement

A. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

B. Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

C. NO TE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

- 52 -- 51 -