Before using this product:
Please read this user manual carefully in order to ensure your safety
and the proper operation of this product. Keep for future reference.
Page 2
Foreword
For Your Safety
Thank you for purchasing this product.
This TT350O camera flash applies to Olympus/Panasonic series
cameras and is compatible with TTL autoflash. With this TTL
compatible flash, your shooting will become simpler. You can easily
achieve a correct flash exposure even in complex light-changing
environments. This camera flash features:
● GN36 (m ISO 100, @105mm).
● Fully support Olympus/Panasonic TTL camera flash. Workable as
Master or Slave unit in a wireless flash group.
● With built-in 2.4GHz wireless remote system to support
transmitting and receiving.
● Provided multiple functions, include manual flash, multi flash, HSS
(up to 1/8000s), second curtain sync, FEC, etc.
● Support with firmware upgrade.
Always keep this product dry. Do not use in rain or in damp
conditions.
This product contains high-voltage electronic parts. Touching
the high-voltage circuit inside it may result in electric shock. Do
not disassemble. Should repairs become necessary, this
product must be sent to an authorized maintenance center.
Stop using this product if it breaks open due to extrusion, falling
or strong hit. Otherwise, electric shock may occur if you touch
the electronic parts inside it.
Do not fire the flash directly into the eyes (especially those of
babies) within short distances. Otherwise visual impairment
may occur. When taking pictures for babies, keep the flash unit
at least 1 meter (3.3 feet) away from them. Using bounce flash
to reduce light intensity is also recommended.
Do not use the flash unit in the presence of flammable gases,
chemicals and other similar materials. In certain circumstances,
these materials may be sensitive to the strong light emitting
from this flash unit and fire or electromagnetic interference may
result.
Do not leave or store the flash unit in places where the ambient
temperature reads over 50°C (e.g. in automobile). Otherwise
the electronic parts may be damaged.
- 25 -
- 26 -
Page 3
E l e c t r o n i c C a m e r a F l a s h
Thinklite TTL Camera Flash
Conventions used in this Manual
● This manual is based on the assumption that both the camera and
camera flash’s power switches are powered on.
● Reference page numbers are indicated by “p.**”.
● The following alert symbols are used in this manual:
The Caution symbol gives supplemental information.
The Note symbol indicates a warning to prevent shooting
problem.
Contents
Foreword
25
For Your Safety
26
Name of Parts
29
Body
Control Panel
LCD Panel
What's in the Box of TT350O?
Separately Sold Accessories
Attaching to a Camera
31
Power Management
32
Flash Mode: TTL Autoflash
32
FEC (Flash Exposure Compensation)
High-Speed Sync
Second-Curtain Sync
Flash Mode – M: Manual Flash
34
Flash Mode – Multi: Stroboscopic Flash
35
Wireless Flash Shooting: Radio (2.4G) Transmission
36
Wireless Settings
Setting Master Unit’s Flash Mode
Setting the Communication Channel
TTL: Fully Automatic Wireless Flash Shooting
M: Wireless Flash Shooting with Manual Flash
Multi: Wireless Flash Shooting with Manual Flash
Other Applications
41
Bounce Flash
Creating a Catchlight
ZOOM: Setting the Flash Coverage and Using the Wide Panel
Low Battery Indicator
C.Fn: Setting Custom Functions
43
Protection Function
44
Firmware Upgrade
45
Technical Data
45
Troubleshooting
47
Compatible Camera Models
48
Maintenance
48
- 27 -
- 28 -
Page 4
MODE ZOOMSYNC SLAVE
SET
Name of Parts
01
02
● LCD Panel
(1) TTL Autoflash
Zoom : zoom display (Page 42)
TTL : TTLautoflash
Focus length (Page 42)
● Body
01. Catchlight Panel
02. Built-in Wide Panel
03. Flash Head
04. Optic Control Sensor
05. Hotshoe
11
10
16
15
● Control Panel
10. <MODE>Mode Selection Button
11. <ZOOM>Zoom Selection Button
12.<SYNC>High-Speed Sync Button
13. <SLAVE> S1/S2 Optic Slave
Triggering Selection Button
(in non-wireless mode)
14. < > Power Switch
15. < > Test Button / Flash Ready
Indicator.
16. < >Custom Function Setting
Button (reusable button, long
- 29 -
08
06
09
07
06. LCD Panel
07. Lock Ring
08. Battery Compartment
09. USB Port
03
04
05
12
13
18
17
14
19
20
: Flash exposure
compensation (Page 33)
(2)M Manual Flash
(3)Multi Flash
(4)Radio Transmission Shooting
● Master Unit
Firing group
Master
Flash exposure
compensation amount
M : Manual flash
Manual flash output
Multi : Stroboscopic flash
Number of flashes
Flash frequency
Flash mode
Channel
press for 2 seconds)
17.< > Wireless Selection
Button (reusable button, long
press for 2 seconds)
● Slave Unit
18. <GR/CH> Group/Channel Button
(reusable button, in wireless
mode)
19. Select Dial
20.<SET> Set Button
Slave
- 30 -
Page 5
● What’s in the Box of TT350O?
1. Flash unit 2. Mini stand 3. Protection case 4. Diffuser
5. Instruction manual
● Separately Sold Accessories
The product can be used in combination with the following
accessories sold separately, so as to achieve best photography
effects: X1T-O wireless flash trigger, Mini softbox, White & Silver
reflector, Honeycomb, Color gels, Snoot, etc.
Power Management
Use Power Switch to power the flash unit on (Long press the
button for one second) or off. Turn off if it will not be used for an
extended period of time. Setting as a master flash, it will turn the
power off automatically after a certain period (approx. 90 seconds)
of idle use. Pressing the camera shutter halfway or pressing any
flash button will wake up the flash unit. Setting as a slave flash, it
will enter sleep mode after a certain period (adjustable, 60 minutes
by default) of idle use. Pressing any flash button will wake it up.
C.Fn
Disabling Auto Power Off function is recommended
when the flash is used off camera. (C.Fn-ST, Page 43)
Flash Mode: TTL Autoflash
Attaching to a Camera
- 31 -
Attach the Camera Flash.
1
● Slip the camera flash’s
mounting foot into the
camera’s hotshoe all the
way.
Secure the Camera Flash.
2
● Rotate the lock ring on the
mounting foot until it locks
up.
Detach the Camera Flash.
3
● Rotate the lock ring on the
mounting foot until it is
loosened.
This flash has three flash modes: TTL, Manual (M), and Multi
(Stroboscopic). In TTL mode, the camera and the flash will work
together to calculate the correct exposure for the subject and the
background. In this mode, multiple TTL functions are available:
FEC, HSS, second curtain sync, etc.
* Press <MODE> Mode Selection Button and three flash modes will
display on the LCD panel one by one with each pressing.
TTL Mode
Press <MODE> Mode Selection Button to enter TTL mode. The
LCD panel will display <TTL>.
● Press the camera release button halfway to focus.
● When the shutter button is fully pressed, the flash will fire a pre-
flash that the camera will use to calculate exposure and flash
output the instant before the photo is taken.
Display“HI”: When the flash output value is up to the maximum
value, “HI”will be displayed and blinking for 3 seconds. Adjust
the camera’s parameters if underexposure appears.
Display“Lo”: When the flash output value is up to the minimum
value, “Lo”will be displayed and blinking for 3 seconds. Adjust the
camera’s parameters if overexposure appears.
- 32 -
Page 6
FEC: Flash Exposure Compensation
ZOOMSYNC SLAVE
SET
MODE ZOOMSYNC SLAVE
SET
MODEZOOMSYNC SLAVE
SET
MODE ZOOMSYNC SLAVE
SET
MODEZOOMSYNC SLAVE
SET
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops.
It is useful in situations where minor adjusting of the TTL system is
needed based on the environment.
Setting FEC:
Press the SET Button and
1 the flash exposure
compensation amount will be
highlighted on the LCD panel.
Turn the Select Dial to set the
2 amount.
● “0.3”means 1/3 step,
“0.7”means 2/3 step.
● To cancel the flash
exposure compensation,
set the amount to “+0”.
Press < SET > button again
3 to confirm the setting.
High-Speed Sync
High Speed Sync (Hss flash) enables the flash to synchronize with
all camera shutter speeds. This is convenient when you want to use
aperture priority for fill-flash portraits.
Press the <SYNC> button to turn on high-speed sync flash and
< > is displayed. Then, adjust the camera’s shutter to achieve
high-speed sync flash.
● With high-speed sync, the faster the shutter speed, the
shorter the effective flash range.
● Multi flash mode cannot be set in high-speed sync mode.
● Over-temperature protection may be activated after 15
consecutive high-speed sync flashes.
● Try to avoid using high-speed sync flash, which will cut
short flash tube’s lifetime.
Note: With the Panasonic cameras in wireless control mode,
the High-Speed Sync may not sync fire.
Second-Curtain Sync
With a slow shutter speed, you can create a light train following the
subject. The flash fires right before the shutter closes.
● Setting the Second-Curtain Sync function on the camera menu,
please read camera instruction manual.
- 33 -
M: Manual Flash
The flash output is adjustable from 1/1 full power to 1/128th power
in 1/3rd stop increments. To obtain a correct flash exposure, use a
hand-held flash meter to determine the required flash output.
Press < MODE > button so
1 that < M > is displayed.
Turn the Select Dial to choose
2 a desired flash output amount.
In high-speed sync mode,
the adjustable flash range is
1/16~1/1.
Flash Output Range
The following table makes it easier to see how the stop changes in
terms of f/stop when you increase or decrease the flash output. For
example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-
0.7, and then increase the flash output to more than 1/2, 1/2+0.3,
1/2+0.7, and 1/1 will be displayed.
Figures displayed when reducing flash output level→
1/1-0.7
1/1-0.3
1/2+0.3
1/2+0.7
←Figures displayed when increasing flash output level
In the M mode, high-speed sync and second curtain sync functions
can be achieved.
Optical S1 Secondary Unit Setting
In M manual flash mode, press the <SLAVE> button so that this
flash can function as an optic S1 secondary flash with optic sensor.
With this function, the flash will fire synchronously when the main
flash fires, the same effect as that by the use of radio triggers. This
helps create multiple lighting effects.
Optical S2 Secondary Unit Setting
Press the <SLAVE> button so that this flash can also function as an
optic S2 secondary flash with optic sensor in M manual flash mode.
This is useful when cameras have pre-flash function. With this
function, the flash will ignore a single “preflash” from the main flash
and will only fire in response to the second, actual flash from the
main unit.
●S1 and S2 optic triggering and off camera high-speed
mode are only available in M manual flash mode.
1/2-0.3
1/4+0.7
1/2-0.7
1/4+0.3
······
1/41/21/1
······
- 34 -
Page 7
Multi: Stroboscopic Flash
MODEZOOMSYNC SLAVE
SET
SET
MODE ZOOMSYNC SLAVE
SET
MODEZOOMSYNC SLAVE
SET
ZOOMSYNC SLAVE
SET
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press <MODE> button so
1 that <Multi> is displayed.
Turn the Select Dial to choose
2 a desired flash output.
Maximum Stroboscopic Flashes:
Hz
Flash
output
1/4
1/8
1/16
1/32
1/64
1/128
1
2
3
4
6
3
2
2
14
14
6
4
30
30
30
20
60
60
60
50
90
90
90
80
90
90
90
90
8-9
12
60
80
20-50
10
2
2
3
2
5
3
5
20
70
2
2
2
2
3
3
5
5
10
10
20
30
5
6-7
2
2
3
3
10
8
40
50
70
80
90
90
60-99
Set the flash frequency and
3 flash times.
● Press the SET Button to
select the flash frequency.
Turn the Select Dial to set
the number.
● Press the SET Button
again to select the flash
times. Turn the Select Dial
to set the number.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
Number of Flashes / Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
● Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
● Using a tripod and a remote control is recommended.
● Stroboscopic flash can be used with“buLb”.
● If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
- 35 -
by the following table.
Wireless Flash Shooting: Radio (2.4G) Transmission
● You can set up three slave groups for TTL autoflash shooting.
With TTL autoflash, you can easily create various lighting effects.
● Any flash settings for the slave units on the master flash in TTL
mode will be automatically sent to the slave units. So the only
thing you need to do is to set the master unit for each slave group
without any operation for the slave units at all during the shooting.
● This flash can work in TTL /M /Multi / OFF flash modes when set
as a master unit.
When using Godox 2.4G wireless X system, TT350O is perfectly
compatible with other products of our company.
As a master unit, TT350O can control the following slave unit
models: AD600, AD600M, AD360II-C, AD360II-N, AD200, V850II,
Tt600.
As a slave unit, TT350O can be controlled by the following master
unit models: X1T-O, V850II, Tt600.
Note: with the TTL functions need the latest firmware version
(please update after 2017-7-1).
● Even with multiple slave units, the master unit can control
all of them via wireless.
● In this user manual, “master unit” refers to the camera flash
on a camera and “slave unit” will be controlled by the
master unit.
1. Wireless Settings
You can switch between normal flash and wireless flash. For normal
flash shooting, be sure to set the wireless setting to OFF.
Master Unit Setting
Long Press the <SYNC>
1 button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < >
is displayed on the LCD
panel, which means the
master unit.
- 36 -
Page 8
Slave Unit Setting
ZOOMSYNC SLAVE
SET
MODE ZOOMSYNC SLAVE
SET
ZOOMSYNC SLAVE
SET
ZOOMSYNC SLAVE
SET
ZOOMSYNC SLAVE
SET
MODE ZOOMSYNC SLAVE
SET
Long Press the <SYNC>
1 button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < > is
displayed on the LCD panel,
which means the slave unit.
2. Setting Master Unit’s Flash Mode
Press the <SLAVE> Button to
1 c hoo se t he g ro up fr om
M/A/B/C. Then, press the
< MODE > Button so that the
master unit can work in OFF / TTL / M flash mode. Choose
one of them as the flash
mode of master unit.
Press the <MODE> Button for
2 2 seconds to switch to Multi
mode.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Long press the <SLAVE>
1 Button for 2 seconds until the
channel IDs is blinking. Turn
the Select Dial to choose a
channel ID from 1 to 16.
Press the <SET> button to
2 confirm.
Slave Unit Setting
2
● Set the TT350O that to be
controlled as the wireless
slave unit. (Page 37)
● The slave unit can be set
as A/B/C.
Check the communication
3 channel
● If the master unit and
slave unit(s) are set to a
different channel, set them
to the same channel.
(Page 37)
Position the camera and
4 flashes
● Position the camera and
flashes as the picture
shows. (Page 40)
Check the flash operation
5
● Press the master unit’s
Test Button< >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
The slave unit might be out of order or fire an unwanted flash
due to the nearby wifi routers or other 2.4G equipments. If in
this case, please adjust the flash’s channel or turn off the 2.4G
equipments.
4. TTL: Fully Automatic Wireless Flash Shooting
Autoflash Shooting with One Slave Unit
Master Unit Setting
1
● Attach a TT350O camera
flash on the camera and set it
as the master unit. (Page 36)
- 37 -
● M/A/B/C can be set as
TTL mode independently.
- 38 -
Page 9
5. M: Wireless Flash Shooting with Manual Flash
SET
MODE ZOOMSYNC SLAVE
SET
MODE ZOOMSYNC SLAVE
SET
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the flash mode to
1 <M>
● Press the <MODE> Button
to set the flash to M mode.
Setting flash output
2
● Turn the Select Dial to set
the flash output of the
groups.
Taking the picture
3
● Each group fires at the set
flash ratio.
6. Multi: Wireless Flash Shooting with Manual
Flash
Setting <Multi>
1 stroboscopic flash.
● Long press the <MODE>
button for 2 seconds so that
<Multi> is displayed. Long
press the <MODE> button
for 2 seconds again to exit.
Setting flash output/flash
2 frequency/flash times.
● Setting the flash
output/flash frequency/flash
times of the groups in the M
mode. Setting the multi flash
mode. (see Page35 )
● A, B and C group can only
control the ON/OFF of the
slave unit by pressing the
<MODE> Button.
Using a flash (master/slave) with a radio transmission wireless
shooting function make it easy to shoot with advanced wireless
multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in the
picture. You can then perform wireless TTL autoflash shooting just
by setting the master unit to <TTL>.
Slave/Master Unit's Positioning and Operation Range
● Autoflash Shooting with One Slave Unit
Transmission distance is about 30m.
● Use the supplied mini stand to position the slave unit.
● Before shooting, perform a test flash and test shooting.
● The transmission distance might be shorter depending on
the conditions such as positioning of slave units, the
surrounding environment and whether conditions.
Wireless Multiple Flash Shooting
You can divide the slave units into two or three groups and perform
TTL autoflash while changing the flash ratio (factor). In addition, you
can set and shoot with a different flash mode for each firing group,
for up to 3 groups.
● Auto Shooting with Two Slave Groups
A
B
● Auto Shooting with Three Slave Groups
C
A
B
- 39 -
- 40 -
Page 10
Other Applications
ZOOMSYNC SLAVE
SET
Bounce Flash
By pointing the flash head toward a wall or ceiling, the flash will
bounce off the surface before illuminating the subject. This can
soften shadows behind the subject for a more natural-looking shot.
This is called bounce flash.
To set the bounce direction, hold the flash head and turn it to a
satisfying angle.
-7 -9 0
27 0
● If the wall or ceiling is too far away, the bounced flash might
be too weak and result in underexposure.
● The wall or ceiling should be a plain, white color for high
reflectance. If the bounce surface is not white, a color cast
may appear in the picture.
Push the wide panel back in.
● Push in only the wide panel.
3
● Follow the same procedures
as for bounce flash.
● Point the flash head straight ahead and then upward by 90°.
The catchlight will not appear if you swing the flash head left
or right.
● For best catchlight effect, stay 1.5m/4.9ft away from the
subject.
ZOOM: Setting the Flash Coverage and Using
the Wide Panel
The flash coverage can be set automatically or manually. It can be
set to match the lens focal length from 24mm to 105mm (135
format). Also, with the built-in wide panel, the flash coverage can be
expanded for 14mm wide-angle lenses.
In Manual Zoom mode, press the
<ZOOM> button.
● Turn the Select Dial to change
the flash coverage.
● AUIf < > is displayed, the flash
coverage will be set
automatically.
● If you set the flash coverage manually, make sure it covers
the lens focal length so that the picture will not have a dark
periphery.
● When the low battery indicator is displayed, the ZOOM can
not be adjusted, it will constantly be 24mm.
Creating a Catchlight
With the catchlight panel, you can create a catchlight in the subject’s
eyes to add life to the facial expression.
Point the flash head upward by
1 90°.
Pull out the wide panel. The
2 catchlight panel will come out
at the same time.
- 41 -
- 42 -
Page 11
Using the Wide Panel
Pull out the wide panel and place it
over the flash head as shown. The
flash coverage will then be extended
to 14 mm.
● The catchlight panel will come out
at the same time. Push the
catchlight panel back in.
● When pull out the wide panel, the ZOOM will constantly be
14mm. The <ZOOM> button will not work.
Low Battery Warning
If the battery power is low, < > will
appear and blink on the LCD panel.
P l ea se r e pl ac e t he b at te ry
immediately. When the low battery
indicator is displayed, the ZOOM can
not be adjusted, it will constantly be
24mm.
C.Fn: Setting Custom Functions
The following table lists the available and unavailable custom
functions of this flash.
C.Fn Custom Functions
Custom Function
Signs
ST
BL
1. Press the < ZOOM > Button for 2 seconds until C.Fn menu is
displayed.
2. Turn the Select Dial to select the Custom Functions.
3. Press the <SET> Button and the Setting No. blinks.
4. Turn the Select Dial to set the desired number. Pressing the
<SET> Button will confirm the settings.
5. Press the <ZOOM> Button to exit.
- 43 -
Function
Auto sleep
(standby)
Backlighting
control
Setting No. Settings & Description
ON
OF
10 sec.
OF
ON
ON
OFF
Off in 10 sec.
Always off
Always lighting
Protection Function
1. Over-Temperature Protection
● To avoid overheating and deteriorating the flash head, do not fire
more than 30 continuous flashes in fast succession at 1/1 full
power. After 30 continuous flashes, allow a rest time of at least 10
minutes.
● If you fire more than 30 continuous flashes and then fire more
flashes in short intervals, the inner over-temperature protection
function may be activated and make the recycling time over 10
seconds. If this occurs, allow a rest time of about 10 minutes, and
the flash unit will then return to normal.
● When the over-temperature protection is started, is shown on
the LCD display.
Number of flashes that will activate over-temperature protection:
Power Output Level
1/1
1/2 +0.7
1/2 +0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
Number of flashes that will activate over-temperature protection in
high-speed sync triggering mode:
Power Output
1/1
1/2(+0.3,+0.7);
1/4(+0.3,+0.7)
1/8(+0.3,+0.7);
1/16(+0.3,+0.7)
2. Other Protections
The system provides real-time protection to secure the device and
your safety. The following lists prompts for your reference:
Prompts on LCD Panel
E1
E3
E9
Number of Flashes
30
40
50
60
100
200
300
500
1000
Times
15
20
30
40
Meaning
A failure occurs on the recycling system so that the
flash cannot fire.
Please restart the flash unit. If the problem still exists,
please send this product to a maintenance center.
The voltage on two outlets of the flash tube is too high.
Please send this product to a maintenance center.
There are some errors occurred during the upgrading
process. Please using the correct firmware upgrade
method.
- 44 -
Page 12
Firmware Upgrade
This flash supports firmware upgrade through the USB port. Update
information will be released on our official website.
USB connection line is not included in this product. The USB
port is a standard Micro USB socket. Common USB
connection line is applicable.
Checking the version: Press the <MODE> Button and the turn
the flash on. Then, the firmware update version (e.g. Version
1.0 will read U-1.0) will be displayed on the LCD panel.
Technical Data
Model
• Type
Compatible Cameras
Guide No.
(1/1 output @ 105mm)
Flash Coverage
Flash Duration (t0.1)
• Exposure Control
Exposure control system
Flash exposure
compensation (FEC)
Sync mode
Multi flash
• Wireless Flash (2.4G radio transmission)
Wireless flash function
Controllable slave groups
Transmission range
(approx.)
Channels
- 45 -
TT350O
Please reference to compatible camera models
36 (m ISO 100)
24 to 105mm
• Auto zoom (Flash coverage set automatically
to match the lens focal length and image size)
• Manual zoom
• Swinging/tilting flash head (bounce flash): 0 to 270°
horizontally and -7° to 90° vertically
1/350 to 1/20000 seconds
TTL autoflash and manual flash
Manual. FEB: ±3 stops in 1/3 stop increments
(Manual FEC can be combined.)
High-speed sync (up to 1/8000 seconds),
first-curtain sync, and second-curtain sync
Provided (up to 90 times, 99Hz)
Master, Slave, Off
3 (A, B and C)
≤30m
16 (1~16)
• Auto Focus Assist Beam
Effective range (approx.)
• Power Supply
AA batteries
Recycle time
Full power flashes
Power saving
• Sync Triggering Mode
• Dimensions
W x H x D
Weight without battery
Center: 0.6~4m
Periphery: 0.6~2.5m
Ni-MH batteries (recommended) or 2*LR6 alkaline batteries
Approx. 0.1-2.2 seconds (eneloop Ni-MH batteries of Panasonic).
Red LED indicator will light up when the flash is ready.
Approx. 210 (2500mA Ni-MH batteries)
Power off automatically after approx. 90 seconds
of idle operation. (60 minutes if set as slave)
Hotshoe, optic triggering
140*62*38 mm
200g
- 46 -
Page 13
TroubleshootingCompatible Camera Models
If there is a problem, refer to this Troubleshooting Guide.
The Camera Flash cannot be charged.
● The battery is installed in the wrong direction.
→Install the battery in the correct direction.
● The camera flash’s internal battery is exhausted.
→If < > appears and blinks on the LCD panel, replace the
battery immediately.
The Camera Flash does not fire.
● The camera flash is not attached securely to the camera.
→Attach the camera’s mounting foot securely to the camera.
● The electrical contacts of the Camera Flash and camera are dirty.
→Clean the contacts.
The power turns off by itself.
● After 90 seconds of idle operation, auto power off took effect if the
flash is set as master.
→Press the shutter button halfway or press any flash button to
wake up.
● After 60 minutes of idle operation, the flash unit will enter sleep
mode if it is set as slave.
→Press any flash button to wake up.
Auto zoom does not work.
● The camera flash is not attached securely to the camera.
→Attach the camera flash’s mounting foot to the camera.
This flash unit can be used on the followingcamera models:
● This table only lists the tested camera models, not all
Olympus/Panasonic cameras. For the compatibility of other
camera models, a self-test is recommended.
● Rights to modify this table are retained.
● Note: With the Panasonic cameras in wireless control mode,
the High-Speed Sync may not sync fire.
Maintenance
● Shut down the device immediately should abnormal operation be
detected.
● Avoid sudden impacts and the product should be dedusted
regularly.
● It is normal for the flash tube to be warm when in use. Avoid
continuous flashes if unnecessary.
● Maintenance of the flash must be performed by our authorized
maintenance department which can provide original accessories.
● This product, except consumables e.g. flash tube, is supported
with a one-year warranty.
● Unauthorized service will void the warranty.
● If the product had failures or was wetted, do not use it until it is
repaired by professionals.
● Changes made to the specifications or designs may not be
reflected in this manual.
The flash exposure is underexposed or overexposed.
● You used high-speed sync.
→With high-speed sync, the effective flash range will be shorter.
Make sure the subject is within the effective flash range
displayed.
● You used Manual Flash mode.
→Set the flash mode to TTL or modify the flash output.
Photos have dark corners or only parts of the target subject
are illuminated.
● The focal length of lens exceeds the flash coverage.
→Check the flash coverage you set. This flash unit has the flash
coverage between 24 and 105mm, which fits medium-format
cameras. Pull the wide panel out to extend the flash coverage.
- 47 -
FCC Warning
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be colocated or operating in conjunction with any other antenna or
transmitter.
- 48 -
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.