深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
地址/Add: 深圳市宝安区福永镇福海大道西新和村华发工业园A4栋
2/F, Building A4, Xinhe Huafa Industrial Zone, Fuhai RD West,
Fuyong Town, Baoan District, Shenzhen 518103, China
电话/Tel: +86-755-25701197 / +86-755-25726373
传真/Fax: +86-755-25723423
邮箱/E-mail: godox@godox.com
82.A0QU6001-03 VB
Instruction Manual
说 明 手 册
Chinese English Bilingual
中英文双语
FOREWORD
FOR YOUR SAFETY
Thanks for choosing Quicker high-speed flash. It has wide-range applicability, not only
perfect for all kinds of studio and workshop photography, but also good at wedding,
portrait, advertisement, and fashion photography. Without recycling time limits,
photographers can capture a series of fast-changing facial expressions and amazing
moves, and clearly freeze each fleetingly perfect instant into eternal beauty. Among the
benefits you’ll enjoy:
Ultra-speedy charging, 0.05-1.2s recycling time
Multi-freeze shots, 1/5000s-1/800s flash duration
Up to 10 shots in one second under high-speed continuous shooting
Exact output control on LED display, 50 steps from 5.0-10.0 by 0.1 increment
High qualified modeling lamp, 150W output adjustable
Outstanding output stability, less than 2% shifts when under the same output
High color stability, ranging within ±100k between flashes over the entire power range
Flash output on/off and power level,modeling lamp and buzzer on/off,and flash triggering can be
controlled by using Godox FT series romote control.
CONTENTS
•
01 Foreword
02 For Your Safety
02 Caution
03 Names of Parts
•
03 Body
•
04 Accessories
•
04 Separately Sold Accessories
04 Operations
•
04 Flash Preparation
•
05 Power Connection
•
05 Modeling Lamp
05 Power Output Control
•
05 Test Button
•
05 Sync Triggering
•
05 Slave Trigger Model
•
06 Buzz Function
•
06 Memory Function
•
06 Wireless Control Function
•
06 Tube Replacement
07 Technical Data
07 Maintenance
To prevent damage to the product or injury to you or to others, read the following safety
precautions in their entirety before using this equipment. Keep these safety instructions
where users can read them for ready reference.
Do not disassemble or modify !
There are high-voltage components inside the unit. Failure to observe this precaution could
result in electric shock or product malfunction. Should the product break open as the result of a
fall or other accident, send the defective back to authorized service center for inspection and
maintenance.
Keep dry !
Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this
precaution could result in fire or electric shock.
Keep out of the reach of children !
This device contains small parts that may pose a choking hazard. Consult a physician
immediately if a child swallows any part of this device.
Do not expose to high temperature !
Do not leave the device in a closed vehicle under the sun or in other areas subject to extremely
high temperature. Failure to observe this precaution could result in fire or damage to the
housing or internal parts.
CAUTION
- After 30 continuous flashes at full power, the flash should be cooled down for about 3
minutes. Overheating will occur if it is used continuously without cooling down.
- Do not keep using the modeling lamp for a long time, otherwise flammable accessories
attaching to flash head, e.g. softbox will get burnt. A 10-minute time is recommended in
this case. After 10 minutes, cool it down for 1 minute.
- When using a snoot, do not keep the modeling lamp on for a long time or fire too
frequently (not over six times for one minute). Overheating will result in damages for
strobe housing and/or studio light.
- Do not touch the lamp cap when the flash or modeling lamp is working, as it will give out
heat, leading to high surface temperature.
- 02 -- 01 -
- Do not touch the two terminals of the tube outlet as there is high voltage inside. Wear
insolated gloves before replacing the tube or modeling lamp.
- Avoid sudden impacts as this can damage the flash tube and/or modeling lamp.
- Do not flash directly towards naked eyes (especially those of babies), otherwise it may
lead to visual impairment.
- Disconnect from the power supply when it will not be used for an extended period.
NAMES OF PARTS
Body
15
12
04
11
07
06
03
02
16
01
17
1. AC Power Socket 8. Slave Model Button SLAVE 15. Light Sensor
2. Sync Cord Jack 9. Test Button 16. Fuse
3. Power Switch 10. Digital Display 17. Mounting Bracket
4. Modeling Lamp Output Controller 11. Modeling Lamp Indicator 18. Umbrellas Input
5. Flash Output Controller 1 2 . B u z z I n dicator 19. Direction Adjusting Handle
6. Modeling Lamp Button MODEL 13. Slave Trigger Indicator 20. Wireless Control Port
7. Sound Button 14. Test Indicator Lamp
- 03 -
18
10
13
05
14
08
09
20
19
Accessories
1. Sync Cord
2. Power Cord
1
2
3
6
3. Standard Reflector
4. Lamp Cover
5. Glass Protection Cover
6. Modeling Lamp
7. Instruction Manual
4
5
Separately sold accessories
The product can be used in combination with the following accessories sold separately, so as to
achieve best photography effects:
FT-16 Remote Control, Power Inverter, Softbox, Photographic Umbrella, Light Stand,
Barndoor, Snoot, etc.
OPERATIONS
Flash Preparation
1. Take down the lamp cover.
Install the modeling lamp and put
on the glass protection cover and
the standard reflector.
(To un ins ta ll t he sta nda rd
reflector, pr ess the ora ng e
release button on the flash head
and turn the standard reflector
counter-clockwise to take it out, as illustrated in the picture.)
2. Attach the flash unit on an appropriate light stand. Adjust the mounting bracket (17) for a
good angle and make sure it’s tightened and fixed. Use the direction adjusting handle (19) to
adjust the flash on a desired direction. Umbrella input (18) is for different photo umbrellas to put
in.
- 04 -
Power Connection
Use the power cord to connect the flash to an AC power source and turn on the power switch
(3). The lamp on the power switch turns on, indicating it’s connected.
Modeling Lamp
Modeling Lamp Button (6) controls the modeling lamp status: when modeling lamp indicator lit
up, modeling lamp turns on;when modeling lamp indicator off,modeling lamp turns off. Modeling
lamp output controller (4) can be used to adjust the modeling lamp power output. Modeling lamp
will turn off automatically after lighting for 2 hours, in case it's forgotten to turn off when user is
not nearby.
When there is flammable accessory on the flash unit, do not keep the modeling lamp on for a
long time. It is recommended to cool it down for one minute after 10 minutes' working.
Power Output Control
Flash output controller (5) decides different power output, satisfying the light requirements in
different environment. The power is adjustable freely from 5.0 to 10.0 which will be accordingly
told on the digital display (10). “OF”on the display indicated that the flash triggering function is
turned off. It can discharge automatically when the flash output is adjusted from high to low.
Test Button
To fire the flash without taking a picture, press the test button (9). It can also help adjust the
flash brightness when combined with the flash output controller (5).
Sync Triggering
The sync cord jack (2) is a Φ6.35mm plug. Insert
a trigger plug here and the flash will be fired
synchronously with the camera shutter.
Slave Trigger Model
Three slave triggering models are available and can be set by pressing Slave Model Button (8).
1) No optical control: The slave triggering indicator (13) is off, indicating the slave triggering
function is shut down.
2) One fire model: The slave triggering indicator (13) glows blue, indicating the flash will fire
synchronously after receiving one external flash. In this model, the flash can function as an
auxiliary lamp, offering various effects of light and shadow.
3) Anti-preflash model: The slave triggering indicator (13) glows red, indicating the flash will
receive two external flashes within 2 seconds and will fire synchronously after receiving the
second flash. In this model, the flash can function as an auxiliary lamp, applicable to TTL
- 05 -
system. With this anti-preflash function, synchronization is supported with cameras having a
one-preflash firing system.
Buzz Function
The sound button (7) is used to decide whether there is sound reminder for ready flash after
recharging. When the buzz indicator (12) turns on, it means buzz function is working; if it turns
off, the buzz function is not working. A “BI” sound will be heard when it’s fully charged.
Memory Function
The device is equipped with memory function for the panel setting. It will help remember the
panel setting 3 second after you set it. When starting up the flash next time, the panel setting
will be the same as the status before powering it off.
Wireless Control Function
By using the wireless power-control flash trigger, you can wirelessly control the on-and-off of
your flash, modeling lamp and buzzer, as well as adjust the flash output level. To start this
function, insert the trigger receiver into the Wireless Control Port (20) and make settings on the
trigger. You can also press the camera shutter-release button to trigger the flash by setting the
transmitter hotshoe onto the camera hotshoe.
Tube Replacement
Shut down the power and remove the power cord before replacing the flash tube and wear
insulated gloves. Then, loosen the iron wire on the tube, keep a balanced hold on the two feet
of the flash tube and pull out the old tube gently. Take down the feet casing from the old tube
and put it on the new one. Hold two feet of the new tube, and target directly towards the two
copper outlets, then push them slightly in. Twine the iron wire on the stainless steel sheet to fix
the flash tube.
- 06 -
TECHNICAL DATA
Model
Max Power (WS)
Guide Number(m ISO 100)
Color Temperature
Operating Voltage
Power Output Control
Modeling Lamp (W)
Recycle Time
Triggering Method
Flash Duration
Fuse
Dimension
Net Weight
Quicker300
300WS
58
sync cord, test button, slave, wireless control port
Flash diameterΦ14CM, height of flash with handle 23CM,
Approx. 2.7KG
Quicker400
400WS
65
5600K±100K
AC200-240V/50HZ
5.0~10.0 (1/1~1/128)
150W
0.05~1.2sec
1/5000S~1/800S
8A
length of flash with lamp cover 41CM
Approx. 2.8KG Approx. 3KG
Quicker600
600WS
76
前 言
感谢您使用闪客高速闪光灯，此系列产品适用广泛，除了能满足各种影楼和摄影
工作室的日常拍摄，在婚纱摄影、广告拍摄、人像摄影、时尚摄影等方面表现尤为出
色。摄影师可以不受回电时间限制，发挥创意尽情拍摄，享受画面捕捉的快感，连续
捕捉一系列最自然的表情和动作，清晰抓拍最精彩的每一刻。产品有以下亮点：
极速回电，0.05-1.2秒回电时间
高速闪光，1/5000-1/800s闪光速度
高速连拍每秒可达10张
50级闪光强度随意选择，LED数码显示屏从5.0-10.0准确定位输出功率
150W大功率造型灯，亮度无级可调
输出稳定，同一功率高速连续输出变化不超过2%
近日光色温，全程色温变化±100k
选配FT无线功率遥控器，可以远程调控闪光灯功率大小、造型灯开关、蜂鸣使能及触
发引闪。
MAINTENANCE
Shut down the device immediately when it works abnormally and find out the reason.
Avoid sudden impacts and the lamp should be dedusted usually.
It’s normal for lamp being warm when in use. Avoid continuous flashes when it is not
necessary.
Maintenance of all the flashes is up to our authorized maintenance department which can
provide original accessories. Users can replace the flash tube and modeling lamp provided
by the manufacturer.
One year warranty period will be cancelled when any unauthorized maintenance is found.
If the product had failures or was wetted, it can be continuously used only after it is repaired
by professionals.
Disconnect the power when doing maintenance work or cleaning.
New changes made to the specifications or designs may not be updated in this manual.
- 07 -
目 录
08 前言 12 功率调节
09 安全须知 12 试闪按钮
09 注意事项 12 同步触发
10 部件 12 光控使用
• •
10 机身 12 声音提示
• •
10 附件 12 记忆存储功能
• •
11 可选购附件 13 无线控制功能
11 使用 13 装卸闪光灯管
•
11 固定闪光灯 13 产品参数
•
11 接通电源 14 维护保养
•
11 造型灯使用
- 08 -
•
•
•
•
•
Loading...