Godox AD200PRO User Manual

Page 1
深圳市神牛摄影器材有限公司
GODOX Photo Equipment Co., Ltd.
地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房21层至4层、41层至4 1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China
电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423 邮箱/E-mail: godox@godox.com http://www.godox.com
705-AD20P0-00
Made in China
中英文双语 / Chinese English Bilingual
说明手册 / INSTRUCTION MANUAL
Page 2
Foreword Warning
Before using this product
Please read this user manual carefully in order to ensure your safety and the proper operation of this product. Keep for future reference.
Thank you for purchasing a GODOX product.
WITSTRO TTL Powerful & Portable Flash AD200Pro include three kinds of flash tube and adopts Godox 2.4G wireless X system. When using GODOX 2.4G wireless X system of camera, AD200Pro can be triggered by X2/X1/XPro series flash trigger in TTL/M/Muilt mode, etc. AD200Pro can also use in combination with GODOX TTL camera flashes, TTL outdoor flashes, TTL studio flashes, etc. With this AD200Pro flash, your shooting will become simpler. You can easily achieve a correct flash exposure even in complex light-changing environments. WITSTRO flash system is a portable photo lighting solution consist of camera flashes, wireless trigger and a range of dedicated light shaping accessories. AD200Pro with lightweight and portable body, strong power, large capacity battery and full speed supply. It offers studio quality light for outdoor and live shooting. The AD200Pro offers:
Compatible wireless TTL system: Fully support TTL/M/Multi functions of Canon,Nikon,Sony,Fuji,Olympus, Panasonic and Pentax cameras.Workable as Slave unit in a wireless flash group. Lightweight and portable: up to 200Ws, is to 3 times powerful as camera flashes ( 600EX ), and the size almost the same. Changeable flash head: Speedlite flash head: Portability, comes with multiple sets of optical glass, even illumination and modeling lamp (LED). Bare bulb flash head: Lighting out with 360 degree angles, all lighting accessories fit for barebulb flashes from most brands.
High-quality AV panel: with clear and convenient operation. Built-in 2.4G wireless transmission: with all-in-one functions and 100 meters further transmission Studio quality light: up to 200Ws, GN 60 (m ISO 100, with bare bulb flash head) / GN52 (Speedlite flash
head). Battery pack: Large-capacity power supply (lithium, 14.4V/2900mAh), 0.01- 1.8s recycling and 500 full power flashes. Wireless control: With built-in Godox 2.4G wireless X system to achieve TTL control. Godox FT-16 flash trigger can also be used to wirelessly adjust flash power level and trigger the flash. AD200Pro has 3.5mm sync cord jack to achieve various sync triggering mode.
Power adjusts from full power to 1/256 in 81 levels.
Change within ± 100K over the entire power range in color temperature mode.
1/8000s high-speed sync flash, high-speed sync triggering.
The powerful and portable AD200Pro meets the demands of freelance commercial photographers, photojournalists, wedding and beach portraiture shooters, event and backpack photographers, photograph enthusiasts, etc.
Always keep this product dry. Do not use in rain or in damp conditions. Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center. Keep out of reach of children. Stop using this product if it breaks open due to extrusion, falling or strong hit. Otherwise, electric shock may occur if you touch the electronic parts inside it. Do not fire the flash directly into the eyes (especially those of babies) within short distances. Otherwise visual impairment may occur. Do not use the flash unit in the presence of flammable gases, chemicals and other similar materials. In certain circumstance, these materials may be sensitive to the strong light emitting from this flash unit and fire or electromagnetic interference may result. Do not leave or store the flash unit if the ambient temperature reads over 50°C. Otherwise the electronic parts may be damaged. Turn off the flash unit immediately in the event of malfunction.
- 23 - - 24 -
Page 3
Contents
23
24
27
31
32
32
32
33
34
36
37
39
40
40
42
43
43
43
Foreword
Warning
Name of Parts
Body
Flash Head
AV Panel
Included Accessories
Separately Sold Accessories
Attaching Bare bulb flash head
Battery
Power Management
Modeling Lamp
Wireless Flash Mode
Flash Mode— TTL Autoflash
TTL Mode
FEC (Flash Exposure Compensation)
High-Speed Sync
Flash Mode—M: Manual Flash
Flash Mode—Multi/Stroboscopic Flash
Wireless Flash Shooting: Ratio (2.4G) Transmission
C.Fn: Setting Custom Functions
Other Applications
Wireless Control Function
Sync Triggering
Protection Function
Technical Data
Troubleshooting
Firmware Upgrade
Maintenance
Conventions used in this Manual This manual is based on the assumption that both the camera and camera flash’s power switches are powered on. Reference page numbers are indicated by “p.**”. The following alert symbols are used in this manual: The Caution symbol indicates a warning to prevent shooting problem. The Note symbol gives supplemental information.
- 25 - - 26 -
Page 4
Name of Parts
Name of Parts
Body:
Flash Head Mounting Socket
Type-C USB Port
Light Sensor
Power Switch
1/4" Mounting Hole
Head Release Button
Wireless Control Port
3.5mm Sync Cord Jack
Battery Release Button
Battery Compartment
Lithium Battery
Control Panel
Flash Head
Speedlite flash head:
Heat Dissipation Hole
Head Mounting Socket
Modeling Lamp (LED)
Optical glass
Modeling Lamp (LED)
Bare bulb flash head:
Tube Socket
Heat Dissipation Hole
Accessory Locking Ring
< MODE > Mode Selection Button
AV Panel
< MENU > Button
<>LED Modeling Lamp < >Test Button
Control Panel
- 27 - - 28 -
< GR/CH >Group/Channel Button
< SET >Set Button
Select Dial
< >Wireless Selection Button/High-Speed Sync Button
Accessory Mount
Flash Head Mounting Socket
Flash Tube
Page 5
Name of Parts
Name of Parts
AV Panel
(1) AV Panel
(2) M Manual Flash
Channel Wireless
Group
C.Fn t0.1
Mask
Time
Beeper
The display will only show the settings currently applied.
● The functions displayed above function buttons 1 to 4, such as and , change according to settings’ status.
When a button or dial is operated, the AV panel illuminated.
t0 1
MK
12
TTL
SYNC
ColorTemperatureMode
c
sec min
Hz
Battery Level
Flash exposure
compensation amount
Flash frequency
Flash high temperature
Modeling lamp(LED)
M : Manual flash
Multi
: HHS
sec min
Standby
S1/S2
(4) Radio Transmission Shooting
Channel
M Mode
T0.1
S1
C.Fn-F2
S1
S1/S2
Radio transmission wireless shooting
Group
Included Accessories
(1) Speedlite flash head (2) Bare bulb flash head (3) AD-E2 holder*1 (4) Battery charger*1 (5) Lithium battery pack*1 (6) Protecting bag*1 (7) Instruction manual*1
(3) Multi Flash
t0 1
MK
t0 1
Manual flash output
1
1
Separately Sold Accessories
Multi : Stroboscopic flash
Number of flashes
Hz
- 29 - - 30 -
Flash frequency
The product can be used in combination with the following accessories sold separately, so as to achieve best
photography effects: Xpro & X1 Wireless Flash Trigger, H200R Round Flash Head,FT-16 Remote Control, Barn
door with 4 wings, Softbox, Beauty Dish, Fold up umbrella, Snoots, Light stand, etc.
3 5 6
42
Page 6
Name of Parts
Power Management
Attaching Bare bulb flash head
1. Remove the reflector or other accessories from the flash head.
2. Match the red dot on the base of the flash tube with the red dot in the Tube Socket (4). Push the flash tube in until it is securely seated into the socket.
Lithium Battery
Features
1. This flash unit uses Li-ion polymer battery which has long runtime. The available charge-and-discharge times are 500.
2. It is reliably safe. The inner circuit is against overcharge, overdischarge, overcurrent, and short circuit.
3. Take only 4 hours to fully charge the battery by using the standard battery charger.
Cautions:
 Do not short circuit.  Do not expose to rain or immerse into water. This battery is not water proof.  Keep out of reach of children.No over 24 hours' continuous charging.Store in dry, cool, ventilated places.Do not put aside or into fire.Dead batteries should be diaposed according to local reglations.Long time not to use, please charge it to 60% and then placed.If the battery had ceased using for over 3 months, please make a full recharge.
ON/OFF Power Switch controls the on/off of the flash unit, turn off the power pack if the flash unit will not be used for an extended period. The product design of power supply with automatic hibernation feature, When unattended operation for a long time (approx. 30/60/90 minutes ), the flash will automatically standby.
Disabling Auto Power standby function is recommended when the flash is used off camera.
C.Fn
(C.Fn-F3, Page 39)
Modeling Lamp
With only the speedlite flash head have modeling lamp function, it will automatic turn off after 30 minutes. Short press the modeling lamp button will control the modeling lamp turn on or off.
Battery Level Indication
Make sure the battery pack is securely loaded in the flash. Check the battery level indication on the AV panel to see the remaining battery level.
Battery Level Indication
on the AV Panel
3 grids
2 grids
1 grid
Blank grid
Blinking
Meaning
Full battery
Medium battery
Low battery
Lower battery, please recharge it.
The battery level is going to be used out immediately. And the flash will auto power off
in 1 minute. Note: Please recharge the battery as soon as possible (within 10 days).
Then, the battery can be used or be placed for long period.
- 31 - - 32 -
Wireless Flash Mode
AD200Pro can only be set as slave unit (receiver end). Short press the wireless selection button to switch the radio transmission function.
Wireless Mode
OFF
Radio Transmission
Flash Mode
M / Multi
TTL / M / Multi
Page 7
t0 1
sec min
Hz
MK
12
c
sec min
Hz
c
Flash Mode — TTL Autoflash
t0 1
sec min
Hz
MK
12
c
sec min
Hz
c
This flash has three flash modes: TTL, Manual (M), and Multi (Stroboscopic). In TTL mode, the camera and the flash will work together to calculate the correct exposure for the subject and the background. In this mode, multiple TTL functions are available: FEC, FEB, FEL, HSS, second curtain sync, modeling flash, control with the camera’s menu screen.
MODE
* Press < > Mode Selection Button and three flash modes will display on the AV panel one by one with each pressing.
TTL Mode
MODE
Press < > Mode Selection Button to enter TTL mode. The AV panel is displayed < TTL >.
With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
Multi flash mode cannot be set in high-speed sync mode.
Over-temperature protection may be activated after 20 consecutive high-speed sync flashes.
Flash Mode — M: Manual Flash
   FEC: Flash Exposure Compensation
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops. It is useful in situations where minor adjusting of the TTL system is needed based on the environment.
Setting FEC:
c
sec
t0 1
MK
12
Press the <SET> Function
1 Button and flash exposure
compensation amount will be highlighted on the AV panel.
min
Hz
Set the flash exposure
2 compensation amount.
Turn the Select Dial to set the amount.
“0.3”means 1/3 step, “0.7”means 2/3 step.
To cancel the flash exposure compensation, set the amount to “+0”.
Press < SET > button again to
3 confirm the setting.
High-Speed Sync
High Speed Sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient when you want to use aperture priority for fill-flash portraits.
The flash output is adjustable from 1/1 full power to 1/256th power in 1/10th stop increments. To obtain a correct flash exposure, use a hand-held flash meter to determine the required flash output.
c
sec
MODE
min
Hz
Turn the Select Dial to choose
2 a desired flash output amount.
Press < SET > button again to
3 confirm the setting.
t0 1
MK
12
Press < > button so that
1 < M > is displayed.
t0 1
MK
12
Long Press Function Button
1 < > for 2 seconds so that
H
< > is displayed.
c
sec min
Hz
Please use the X1 series
2 transmitter to trigger.
- 33 - - 34 -
Page 8
Optic S1 Secondary Unit Setting
t0 1
sec min
Hz
MK
12
c
sec min
Hz
c
In M manual flash mode, press the <MENU> button to enter C.FN-F2 to choose S1 function, so that this flash can function as an optic S1 secondary flash with optic sensor. With this function, the flash will fire synchronously when the main flash fires, the same effect as that by the use of radio triggers. This helps create multiple lighting effects.
Optic S2 Secondary Unit Setting
Press the <M EN U> b utton to enter C.FN-F 2 to choose S2 function , so that this flash can al so function as an optic S2 second ary flash with opti c se nsor in M manual flas h mo de. Th is is useful when camer as have pre-flash func tion. With this funct ion, the flash will i gn ore a single “prefl as h” from the main flas h an d will only fire in respo nse to the second, actu al flash from the mai n un it.
S1 and S2 optic triggering is only available in M manual flash mode.
Display Flash Duration
Flash duration refers to the length of time that from flash’s firing to reach the half peak at maximum. The half peak at maximum is usually expressed as t=0.5. In order to provide the photographer with more concrete data, this product adopts t=0.1. The difference between t=0.5 and t=0.1 is shown in the following picture.
A
50%
t=0.5
t=0.1
Display Flash Duration Operation
1. Press the <MENU> button to enter C.FN function.
2. Adjust the Select Dial to F6, the t0.1 icon will be displayed on the AV panel.
3. Press <SET> button to enter the adjustment condition.
4. Turn the Select Dial to choose the ON/OFF.
The flash duration will only be displayed on the AV panel in M mode.
StableColorTemperatureFunction
When use this function, the color temperature changes within ±100K over the entire power range: enter MENU C.Fn-08 and set it as ON, which means the color temperature function is turned on. When adjusting the power output from high to low in M mode, Flash Ready Indicator will blink (the beeper will alarm for 1 minute). Now press the Test Button to discharge, and the flash can be used as normal.
This function can only be supported in M non-high-speed mode.
10%
t0 1
MK
12
- 35 -
t
c
sec min
Hz
©
t0 1
MK
12
Flash Mode — Multi: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number of flashes, and the flash output.
c
sec
t0 1
MK
12
Press <MODE> button so that
1 <MULTI> is displayed.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the shutter speed and set it with the camera.
Number of Flashes / Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2 seconds.
To avoid overheating and deteriorating the flash head, do not use stroboscopic flash more than 10 times in succession. After 10 times, allow the camera flash to rest for at least 15 minutes. If you try to use the stroboscopic flash more than 10 times in succession, the firing might stop automatically to protect the flash head. If this happens, allow at least 15 minutes' rest for the camera flash.
Stroboscopic flash is most effective with a highly reflective subject against a dark background.
Using a tripod and a remote control is recommended.
A flash output of 1/1 and 1/2 cannot be set for stroboscopic flash.
Stroboscopic flash can be used with“buLb”.
If the number of flashes is displayed as “--”, the firing will continue until the shutter closes or the battery is exhausted. The
number of flashes will be limited as shown by the following table.
c
sec min
Hz
Maximum Stroboscopic Flashes:
Flash Output
1/4
1/8
1/16
1/32
1/64
1/128 1/256
min
Hz
t0 1
Turn the Select Dial to choose
2 a desired flash output.
Hz
Set the flash frequency and flash
3 times.
Press < SET > button to select the flash frequency. Turn the Select Dial to set the number.
● Press < SET > button to select the flash times. Turn the Select Dial to set the number.
● After finish the setting, press <SET> button and all the settings will be displayed.
Hz
1
2
3
4
5
6-7
8-9
10
11
12-14
15-19
7
6
5
4
4
3
3
2
2
2
2
14
14
12
10
8
6
5
4
4
4
4
30
30
30
20
20
20
10
8
8
8
8
60
60
60
50
50
40
30
20
20
20
18
90
90
90
80
80
70
60
50
40
40
35
90 90 90 90 90 90 80 70 70 60 50 40 40
- 36 -
20-50
2
4
8
16
30
60-99
2
4
8
12
20
Page 9
Wireless Flash Shooting
t0 1
sec min
Hz
MK
12
c
sec min
Hz
c
AD200Pro adopts Godox 2.4G wireless X system, which has good compatibility with other products of our company. As a slave unit, AD200Pro is automatically compatible with Canon/ Nikon/ Sony TTL system according to the master unit. Nikon cameras (use X1T-N), Canon cameras (use X1T-C) and Sony cameras (use X1T-S) can use one or more AD200Pro-TTL flashes simultaneously.
1. Wireless Settings
Press the wireless selection button to switch wireless function ON/ OFF. Turn the wireless function on, the < > icon will be displayed on the AV panel. When using the FT-16 remote control or others trigger, please turn off the wireless function.
4. Wireless ID Settings
Press the MENU button to enter C.Fn to choose OFF or any figure from 01-99. Note: This can only be used when the master unit possesses the wireless ID function.
Positioning and Operation Range
(Example of wireless flash shooting)
Autoflash Shooting with One Slave Unit
Transmission distance is about 100m
c
sec
t0 1
MK
12
min
Hz
2. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the channel IDs to prevent signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same.
c
sec
t0 1
MK
12
Long press the <GR/CH>
1 Button for 2 seconds, so that
min
Hz
Turn the Select Dial to choose
2 a channel ID from 1 to 32.
Press the <SET> button to
3 confirm.
the icon will be displayed on the AV panel.
3. Setting the Communication Group
Short press the < GR/CH > button to choose group ID from A to E.
Use the supplied stand to position the slave unit.
● Before shooting, perform a test flash and test shooting.
● The transmission distance might be shorter depending on the conditions such as positioning of slave units, the surrounding environment and whether conditions.
● With a lot of wireless signal interference conditions, if you miss flash, please change the wireless communication channel.
Wireless Multiple Flash Shooting
You can divide the slave units into two or three groups and perform TTL autoflash while changing the flash ratio (factor). In addition, you can set and shoot with a different flash mode for each firing group, for up to 5 groups.
Auto Shooting with Two Slave Groups
A
B
Auto Shooting with Three Slave Groups
C
A
B
c
sec
t0 1
MK
12
min
Hz
When using the AD200Pro and Godox X1 series trigger togetherthe X1 can control the flash function such as:
Flash Mode: TTL, M, Multi Sync Mode: First-curtain sync, second-curtain sync and High-speed sync
Control the power levelModeling Lamp turn on or offBeeper turn on or off
- 37 - - 38 -
Page 10
C.Fn: Setting Custom Functions
Other Applications
The following table lists the available and unavailable custom functions of this flash.
Custom Function Signs
F1
F2
F3
F4
F5
F6
F7
F8
Functions
Beeper
S1/S2 mode
selection
Auto standby
Delay flash
Mask
t0.1 display
ID Setting
Stable Color
Temperature Mode
Setting Signs
ON
OFF
OFF
S1
S2
OFF
30 min
60 min
90 min
OFF, 0.01~30s
OFF
N1
N2
ON
OFF
OFF
01-99
OFF
ON
Settings & Descriptions
ON
OFF
OFF
S1 mode
S2 mode
OFF
Auto standby
without
any operation
Can be triggered
as second curtain
OFF
ON: Trigger 2 times for
1 cycles,
1th flash of trigger.
ON: Trigger 2 times for
1 cycles,
2th flash of trigger.
Display
Not display
OFF
Choose any figure from 01-99
OFF
ON
Restrictions
NO
M mode
NO
M/Multi mode
M mode
M mode
Wireless mode
M non-high-speed mode
1. Press the < MENU > button to enter the C.Fn meun.
2. Select the custom function No.
Turn the Selection Dial to select the custom function No.
3. Change the setting
Press < SET > button and the Setting No. blinks.
Turn the Select Dial to set the desired number. Press < SET > button will confirm the settings.
4. Exit C.Fn menu
Press < MENU > button to exit.
Wireless Control Function
The flash unit is built in with a Wireless Control Port so that you can wirelessly adjust the power level of the flash and the flash triggering. To control the flash wirelessly, you need a FT-16 remote control set (on­camera and on-flash). Insert its receive end into the Wireless Control Port on the flash and insert the transmit end into the camera hot shoe. Settings made on the hotshoe-mounted transmit and receive ends will be wirelessly communicated to the flash. Then you can press the camera shutter release button to trigger the flash. You can also hold the transmit end at hand to control your off-camera flash.
For full instructions on the use of FT series remote control, see
its user manual.
Turn off the AD200Pro wireless function.
Sync Triggering
The Sync Cord Jack is a Φ3.5mm plug. Insert a trigger plug here and the flash will be fired synchronously with the camera shutter.
Protection Function
1. Over-Temperature Protection
To avoid overheating and deteriorating the flash head, do not fire more than 40 continuous flashes in fast
succession at 1/1 full power. After 40 continuous flashes, allow a rest time of at least 10 minutes.
If you fire more than 40 continuous flashes and then fire more flashes in short intervals, the inner over-
temperature protection function may be activated and make the recycling time over 10 seconds. If this occurs, allow a rest time of about 10 minutes, and the flash unit will then return to normal.
When the over-temperature protection is started, is shown on the AV display.
Number of flashes that will activate over-temperature protection:
Power Output Level
1/1
1/2+0.7
1/2+0.3
1/2
1/4(+0.3,+0.7)
1/8(+0.3,+0.7)
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
1/64(+0.3,+0.7)
1/128(+0.3,+0.7)
1/256(+0.3,+0.7)
Number of Flashes
Speedlite flash head
40
50
60
75
100
200
300
500
1000
Bare bulb flash head
60
80
100
120
150
200
300
500
1000
- 39 - - 40 -
Page 11
Number of flashes that will activate over-temperature protection in high-speed sync triggering mode:
Power Output
1/1
1/2(+0.3,+0.7);
1/4(+0.3,+0.7);
1/8(+0.3,+0.7);
1/16(+0.3,+0.7)
1/32(+0.3,+0.7)
Times
Speedlite flash head
20
30
50
75
80
100
Bare bulb flash head
50
60
75
100
150
200
1/64(+0.3,+0.7);
1/128(+0.3,+0.7);
1/256(+0.3,+0.7)
2. Other Protections
The system provides real-time protection to secure the device and your safety. The following lists prompts
for your reference:
Prompts on LCD Panel
E1
E2
E3
E9
Meaning
A failure occurs on the recycling system so that the flash cannot fire.
Please restart the flash unit. If the problem still exists, please send
this product to a maintenance center.
The system gets excessive heat. Please allow a rest time of 10 minutes.
The voltage on two outlets of the flash tube is too high. Please send this
product to a maintenance center.
There are some errors occurred during the upgrading process. Please
using the correct firmware
upgrade method.
Technical Data
Model
Wireless Slave Unit Mode
Flash Mode
Compatible Cameras under Radio
Transmission (as slave unit)
Guide No. (1/1 Output)
Flash Duration t.01 (approx.)
POWER
Power Output
Stroboscopic Flash
Flash Exposure Compensation (FEC)
Sync mode
Delay Flash
Mask
Beeper
Modeling Lamp (LED)
Optic Slave Flash
Flash Duration Indication
Wireless Flash (2.4G transmission)
Wireless flash function
Controllable slave groups
Transmission range (approx.)
Channels
ID
Power Supply
Power Supply
Full Power Flashes
Recycle Time
Battery Indicator
Power Indication
Sync Triggering Mode
Color Temperature
Stable Color Temperature
Dimensions
Dimension
Net Weight
AD200Pro
Radio transmission mode (compatible with Nikon & Canon & Sony& Fujifilm & Olympus
& Panasonic & Pentax )
Wireless off
Slave unit of radio transmission
Nikon cameras (X1T-N as master unit)
Canon EOS cameras (X1T-C as master unit)
Sony cameras (X1T-S as master unit)
Fujifilm cameras(X1T-F as master unit)
Olympus cameras(X1T-O as master unit)
Speedlite flash head: 52 (m ISO 100, @35mm)
Bare bulb flash head: 60 (m ISO 100, with the AD-S2 standard reflector, @28mm)
Speedlite flash head: 1/220 to 1/15380 seconds
Bare bulb flash head: 1/220 to 1/13510 seconds
200W
9 steps: 1/256~1/1
Provided (up to 90 times, 99Hz)
Manual. FEB: ±3 stops in 1/3 stop increments.
High-speed sync (up to 1/8000 seconds), first-curtain sync, and second-curtain sync
0.01~30 seconds
S1/S2
Slave, Off
5 (A, B, C, D, and E)
100m
32 (1~32)
01~99
Lithium battery pack (14.4V/2900mAh)
500
Approx. 0.01-1.8s
Power standby automatically after approx. 30 minutes of idle operation.
3.5mm sync line, Wireless control port
5600±200k
Change within ±100K over the entire power range in color temperature mode.
172x54x75mm (flash head not included)
590g (flash head & battery not included)
M/Multi
TTL/ M/Multi
- 41 -
- 42 -
Page 12
Firmware Upgrade
USB connection line is not included in this product. The USB port is a Type-C USB socket.Type-C USB connection line is applicable.
As the firmware upgrade needs the support of Godox G3 software, please download and install the "Godox G3 firmware upgrade software" before upgrading. Then, choose the related firmware file.
As the product needs to do firmware upgrade, please refer to instruction manual of the newest electric version as final.
Maintenance
Shut down the device immediately should abnormal operation be detected.
Avoid sudden impacts and the product should be dedusted regularly.
It is normal for the flash tube to be warm when in use. Avoid continuous flashes if unnecessary.
Maintenance of the flash must be performed by our authorized maintenance department which can provide original accessories.
This product, except consumables e.g. flash tube, is supported with a one-year warranty.
Unauthorized service will void the warranty.
If the product had failures or was wetted, do not use it until it is repaired by professionals.
Changes made to the specifications or designs may not be reflected in this manual.
- 43 -
- 44 -
Loading...