Gocontrol GD00Z-4 Installation Instructions Manual

GD00Z-4
GARAGE DOOR OPENER REMOTE COMMAND TRANSCEIVER with TILT SENSOR
Installation Instructions
PRODUCT DESCRIPTION
PRODUCT COMPONENTS
TILT SENSOR INSTALLATION AND BATTERY
PAIRING (INCLUDING) WITH THE SYSTEM
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-4 - P/N: 236956 BX2 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
WARNING
This operator system is equipped with an unattended operation feature. This door could move unexpectedly. NO ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
This system can be installed on sectional type (roll up) doors only per (UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
WARNING
Do not install the Remote Command Transceiver on garage door operators manufactured prior to 1993 (models without an operational safety beam entrapment detection system).
WARNING
The Remote Command Transceiver must be mounted in the garage, in sight of the garage door, where the visual and audible movement warning indicators can be clearly seen and heard.
GD00Z-4
POWER
INPUT
JACK
WARNING
LIGHT
LINK
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
FOR GD00Z-4
POWER SUPPLY
TILT
SENSOR
STATUS
INDICATOR
OPTIONAL
ADJUSTABLE
GD00Z-4 MOUNTING
BRACKET
POWER
SUPPLY
RETAINING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
SCREW FOR
POWER SUPPLY
BRACKET
WIRE
TIES
TO INCLUDE THE GD00Z-4 INTO YOUR CONTROLLER
1
2
WALL
OUTLET
POWER SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
GD00Z-4
Press and release the link button on the GD00Z-4.
Note: Plug in the GD00Z-4 near your Z-Wave Controller for these steps
Place your Z-Wave Controller into Discovery or Include mode.
TO EXCLUDE THE GD00Z-4 FROM YOUR CONTROLLER
Confirm that the GD00Z-4 was recognized by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on including devices.
3
1
2
Press and release the link button on the GD00Z-4.
Place your Z-Wave Controller into Exclude mode.
Confirm that the GD00Z-4 was excluded by your Z-Wave Controller.
Refer to your Z-Wave Controllers instructions for additional information on excluding devices.
3
CR2032
PLUS SIDE UP !!!
The system will notify you when the battery is low, replace the battery with a type CR2032 coin cell
Insert the battery into the transmitter
To open the case, twist a small screwdriver in case slot
SLOT
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
POST ON BOTTOM
"UP"
ARROWS
Snap the sensor onto the mounting plate
To activate the tilt sensor, remove the battery protection pull strip
2
ARROWS ON PLATE & SENSOR POINT UP
LOW BATTERY REPLACEMENT
1
2
1
3
Attach the mounting plate to the top panel of the door
GD00Z-4 Overview
• A garage door opener remote command transceiver with built-in Z-Wave technology.
• Allows remote operation of a garage door opener using Z-Wave controllers.
• Acts as a Z-Wave repeater to improve communications within the Z-Wave mesh network.
GD00Z-4 Summary of Operation
• GD00Z-4 connects to the garage door opener’s pushbutton wall console terminals.
• A wireless tilt sensor mounts on the garage door and reports the door’s position to the GD00Z-4.
• GD00Z-4 responds to Z-Wave commands from Z-Wave controllers to open or close the garage door.
• A warning indicator light fl ashes and a beeper sounds for 5 seconds before the door begins to move.
• If the door does not completely open or close, a second open or close command can be sent after 30 seconds.
• If the door does not completely open or close after the second attempt, the GD00Z-4 operation is suspended until a local garage door pushbutton is activated.
Z-Wave Information
• Z-Wave® is a registered trademark of Sigma Designs Inc. and/or its subsidiaries.
• Z-Wave is an Interoperable two-way RF mesh networking technology designed for use with a Z-Wave gateway/ controller and other Z-Wave enabled devices.
• Replication is the process of copying or transferring your Z-Wave network from one controller to another.
• This is a Security enabled Z-Wave product and must be used with a Security enabled Z-Wave controller in order to fully utilize this product. As such, this device will not respond to Basic CC commands.
• ASSOCIATION: The GD00Z-4 supports 1 Group with 1 Node. Group 1 must be assigned the Node ID of the controller to which unsolicited notifi cations from the GD00Z-4 will be sent. The Z-Wave controller should set this association automatically after inclusion.
GD00Z-4 MOUNTING
GD00Z-4 CONNECTIONS
SYSTEM OPERATION
OPERATION NOTES
1. The warning light will fl ash and the warning beeper will sound for fi ve seconds before the door opener is activated. STAY CLEAR OF THE DOOR, AND DOOR
OPENER. THEY ARE ABOUT TO MOVE!
2. If the door does not completely open or close after remote activation, the GD00Z-4
will allow user to try to operate the door one more time. If the second attempt fails, the GD00Z-4 will go into lock-out mode. See Note #3.
3. If the GD00Z-4 is in lock-out mode and will not accept remote commands, activate the door from the pushbutton wall console.
4. Once the GD00Z-4 has initiated the movement of the garage door, another command cannot be sent for 30 seconds. This eliminates the chance of “bouncing” the garage door and possibly damaging the garage door opener.
TROUBLESHOOTING
PROBLEM
POSSIBLE
CAUSE
CORRECTIVE ACTION
Unable to include in Z-Wave network.
GD00Z-4 was not properly excluded from a previous Z-Wave network.
Reset the GD00Z-4 by pressing the LINK button 5 times. A quick beep then a longer beep indicates the reset. Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
The GD00Z-4 does not fl ash or beep when activated.
No power to the GD00Z-4.
1. Make sure the power supply is plugged in securely to a live outlet.
2. Make sure the power cord is plugged in securely to the GD00Z-4.
The GD00Z-4 fl ashes and beeps when activated but the door does not move.
Obstruction blocking the door or incorrect wiring.
1. Make sure that there are no obstacles preventing the door from moving.
2. Make sure that the GD00Z-4 connection wires are connected to the proper terminals on the garage door opener. Trace the wires from the garage door opener’s pushbutton wall console to the door opener. This is where the GD00Z-4 connection wires should be connected.
Garage door opens or closes, but the status does not change on the Z-Wave Controller.
The tilt sensor signal is not being received by the GD00Z-4.
1. Make sure the tilt sensor is mounted correctly on the garage door, with the arrow pointing up.
2. Make sure the battery pull tab has been removed from the tilt sensor.
3. Replace the battery in the tilt sensor.
NORTEK SECURITY & CONTROL LIMITED WARRANTY
What is Covered?
Nortek Security & Control (“NS&C”) warrants to consumers who purchase this product for personal, family or household purposes new from NS&C directly or from an authorized NS&C dealer, that the product will be free from defects in materials and workmanship for a period of (1) year from the date of purchase. This warranty only applies if the product is installed at a residence in the 50 United States or District of Columbia, and only at the site of the original installation. It is not transferable. This warranty is not extended to resellers. If a defect exists, NS&C will have you ship the defective part or product to us and we will, at our option, either repair or replace it. This warranty does not cover defects or damages caused by improper handling, maintenance, storage, installation, removal or re-installation, misuse, non-factory authorized modifi cation or alteration, use of incompatible accessories, electrical power problems or surges, impact by foreign objects, accident, fi re, acts of God, normal wear and tear or shipping damage other than a shipment from NS&C. Note that all NS&C products are designed to be installed, removed and serviced by trained individuals or professionals. Keep your original sales receipt as it will be required to obtain warranty service.This warranty shall not be extended or restarted upon receipt of any repaired or replacement part or product under this warranty. No person is authorized to extend or otherwise modify this warranty.
How do I Obtain Warranty Service?
To obtain warranty service, email our Returns Department at returns@nortek.com. Include your name, address, telephone number, the model number of your product, a copy of your original sales receipt, and a description of the problem. Unless we need to discuss the situation further with you, you will be emailed a Return Authorization Number and shipping instructions. If we need to discuss the situation further with you, we will call or email you. NS&C may require troubleshooting on installed product before a Return Authorization Number is issued. Anything shipped to us without a Return Authorization Number will be automatically returned unopened. You are responsible for the charges for shipment to us, unless you are a California resident.
Limitations
THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXCEED THE WARRANTY PERIOD PROVIDED HEREIN.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
NS&C SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE BREACH OF ANY WRITTEN OR IMPLIED WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.This warranty gives you specifi c legal rights, and you may also have other legal rights which vary from State to State.
REGULATORY NOTICES
Changes or modifi cations not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Les changements ou modifi cations non approuvés expressément par la partie responsable de la conformité pourrait annuler
l’autorité de l’utilisateur à faire fonctionner l’équipement. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00Z-4 - P/N: 236956 BX2 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 2 OF 2
The GD00Z-4 typically mounts on the ceiling near the opener and the power outlet
Tilt sensor mounted on the top panel of the door
THE GD00Z-4 CAN ALSO BE ATTACHED TO THE OPENER'S
HARDWARE USING THE ADJUSTABLE MOUNTING BRACKET
THE GD00Z-4 WARNING
LAMP MUST BE VISIBLE IN
ALL DOOR POSITIONS
3/16" HOLES
FOR ANCHORS
The optional adjustable mounting bracket fits 3 ways on the GD00Z-4
The bracket snaps onto indents on either side or on the end of the GD00Z-4
Secure bracket with screw
Use the four screws and anchors to mount the GD00Z-4 above the opener
INDENT
INDENT
Use the bolts and nuts supplied to attach the bracket to a secure structure
BE SURE THE GD00Z-4 IS CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND THE WARNING LAMP IS NOT OBSTRUCTED
INDENT
1A
2A
REMOVE POWER FROM THE
GARAGE DOOR OPENER
BEFORE CONTINUING
! WARNING !
1
PUSHBUTTON
PUSHBUTTON
GARAGE
DOOR
OPENER
Connect the GD00Z-4 connection wires to the pushbutton wall console terminals on the garage door opener. The terminals may be named "PWC", "WC", "PB", "PUSHBUTTON", or "RED and WHITE". Terminal names and locations vary by model.
DO NOT DISCONNECT
ANY WIRES CURRENTLY
CONNECTED TO THE
GARAGE DOOR OPENER !!!
Remove the screw from 120 VAC outlet faceplate. Secure the retaining bracket to the faceplate with the provided screw. Snap the power supply into the bracket while plugging into the outlet.
USE WIRE TIES TO SECURE EXCESS WIRING CLEAR OF ALL MOVING PARTS OF THE GARAGE DOOR AND OPENER
Either wire can connect to either terminal
Plug the power cord into the power input jack on the GD00Z-4
2
1
3
FLASH
FLASH
FLASH
BEEP
BEEP
BEEP
Use your Z-Wave Controller to activate your garage door opener
The GD00Z-4 will activate the door opener and open or close the door
STAY CLEAR
OF THE DOOR !!!
3
The GD00Z-4 will beep and flash for five seconds before the door moves
4
5
Restore power to your garage door opener
1
To synchronize the system, use the garage door opener's pushbutton to manually open and close the door
2
STAY CLEAR
OF THE DOOR !!!
Copyright © 2015 Nortek Security & Control LLC 236956 BX2
GD00Z-4 Specifi cations
Power Supply: Input: 120 VAC, 0.8 A Output: 12 VDC, 2 A
Operating Temperature: -4°—122° F (-20°—50° C)
Audible Alarm: 45 db @ 10 feet
Strobe: 360 Lumens
Communications: Z-Wave (908.4 MHz)
Mounting: Screws and anchors to
the ceiling, or bracket to the opener’s hanging hardware
Tilt Sensor Specifi cations
Power Supply: Type CR2032 Coin Cell Battery
Operating Temperature: -4°—122° F (-20°—50° C)
Battery Life: 24 Months (typical)
Communications: Proprietary 345 MHz
Range: 100 feet line-of-sight to GD00Z-4
Mounting to Garage Door: Double-sided tape or two
mounting screws
(Specifi cations subject to change without notice)
NOTICE TO USERS IN CALIFORNIA - CR COIN CELL LITHIUM BATTERY INFORMATION: THIS
PRODUCT CONTAINS A CR COIN CELL LITHIUM
BATTERY WHICH CONTAINS PERCHLORATE
MATERIAL - SPECIAL HANDLING MAY APPLY - SEE
www.dtsc.ca.gov/hazardouswaste/perchlorate
KEEP AWAY FROM SMALL CHILDREN. IF BATTERY
IS SWALLOWED, PROMPTLY SEE A DOCTOR. DO
NOT TRY TO RECHARGE THIS BATTERY. DISPOSAL
OF USED BATTERIES MUST BE MADE IN
ACCORDANCE WITH THE WASTE RECOVERY AND
RECYCLING REGULATIONS IN YOUR AREA.
Loading...