Goboservice GOLIVE150 Instruction Manual
Goboservice Lighting by Sunland Optics SRL
Via Don Minzoni 14 , 89125 Reggio Calabria
+39 0965 813264
Via Lombardia 269, 20861 Brugherio (MB)
+39 02 23166538
www.goboservice.com
info@goboservice.com
INSTRUCTION MANUAL
ENGLISH
GOLIVE150
- 3 -
ENGLISH
Thank you for choosing our projector ! We inform you that this product was designed and realized to
guarantee you the best performance and to satisfy as much as possible your expectations and
requirements.
Please read carefully each part of this instruction manual before start to use the product and use it each
time you have some difficulties or doubt.
The following instruction manual is a key part of this purchasing. It must be carefully stored for a period
of not less 10 (ten) years, in a known place and easily accessible to all interested people.
The knowledge and respect of manual contents are essential in order to guarantee the correct and safe
installation, use and maintenance of the product.
The Goboservice by Sunland Optics SRL company disclaims all liability for damage to the projector or to
other property or persons deriving from installation, use and maintenance that is not carried out in
accordance with that reported in this instruction manual, which must always accompany the unit.
Moreover Goboservice by SunlandOptics SRL reserves the right to change the information in this
instruction manual at any time and without notice.
- 4 -
WWW.GOBOSERVICE.COM
SUMMARY
1. SAFETY INFORMATION ................................................................................................................................................... 5
2. PACKAGE CONTENT ........................................................................................................................................................ 7
3. PROJECTOR INSTALLATION .......................................................................................................................................... 8
3.1. FRONT SIDE VIEW OF PROJECTOR ..................................................................................................................... 8
3.2. BACK SIDE VIEW OF PROJECTOR ......................................................................................................................... 8
3.3. LENS MOUNTING or SUBSTITUTION .................................................................................................................. 8
3.4. LAMP MOUNTING or SUBSTITUTION ................................................................................................................. 9
3.5. ISTRUZIONI DI MONTAGGIO DEI GOBO ......................................................................................................... 10
3.6. ACCESSORIES POWER SUPPLY ........................................................................................................................... 11
4. USE OF PROJECTOR ....................................................................................................................................................... 12
4.1. CONNECTION OF PROJECTOR TO THE MAINS SUPPLY ............................................................................ 12
4.2. PROJECTOR ORIENTATION .................................................................................................................................. 12
4.3. PROJECTED IMAGE FOCUS .................................................................................................................................. 12
5. THECNICAL DATA ........................................................................................................................................................... 13
6. POSSIBLE PROBLEMS - CAUSES AND SOLUTIONS .............................................................................................. 14
7. DIRECTIVES ........................................................................................................................................................................ 14
8. DISPOSAL ........................................................................................................................................................................... 14
9. WARRANTY ....................................................................................................................................................................... 15
10. MAINTENANCE HISTORY ........................................................................................................................................... 16
GOLIVE150
- 5 -
ENGLISH
1. SAFETY INFORMATION
Please read carefully the following safety instructions before do any operations. The product describes in
this instructions manual is a lighting fixture for the projection of a light beam. It is used usually to light,
with an high level of surface brightness, small areas on which to project decorative effects or fascinating
and special logos and images. The projector must be only used for the purpose it was designed and
built for. It is suitable to illuminate indoor and outdoor environments, any other use is not approved by
the manufacturer and for this reason disclaims any liability for damages resulting from improper or
incorrect use. This unit should be disposed of according to your country’s regulations regarding the
differentiated waste collection and disposal.
1. INSTALLATION – Please pay attention that during installation there is not any
hinders on the place on which the projector has to be installed. The projector
must be attached with dowels or screws or other anchorages suitable with the
material to be blocked. Make sure that all parts for fixing the projector are in a
good state of repair and check the stability of the point of anchorage before
positioning the projector.
2. MINIMUM DISTANCE OF ILLUMINATED OBJECTS – The projector must be
placed so that the objects hit by the beam of light are at least 2,0 meters from
the lens of projector.
3. MINIMUM DISTANCE FROM FLAMMABLE MATERIALS – The projector must be
placed so that the any flammable materials is at least 1,0 meters from every
point on the surface of the fitting.
4. MAXIMUM AMBIENT TEMPERATURE – Place the projector in a place where
there is a good air flow. Please don’t use it in closed or semi-closed
environments because this could cause an increase of temperature with a
reduction of projector life cycle. For a safe functioning of projector the
temperature must not exceed 45°C.
5. PROTECTION AGAINST INDIRECTS CONTACTS – It is mandatory connect the
projector to a mains supply system fitted with efficient earthing (Class I
appliance accableing to standard EN 60598-1). It is, moreover, recommended
to protect the supply lines of the projectors from indirect contact and/or
shorting to earth by using appropriately sized residual current devices.
6. CONNECTION TO MAIN SUPPLY - Connection to the electricity mains must be
carried out by a qualified electrical installer. Check that the mains frequency
and voltage correspond to those for which the projector is designed. Evaluate if
the mains supply can withstand the power consuption of projector and, if it is,
verify the maximum number of devices that it is possible connect to the
electricity line in order to avoid overloading.
- 6 -
WWW.GOBOSERVICE.COM
7. TEMPERATURE OF EXTERNAL SURFACE –The maximum temperature that can
be reached on the external surface of the fitting, in a thermally steady state, is
60°C.
8. PROTECTION RATING - Direct exposure of the projector to rain, snow, hail or
other liquids may damage the product. The projector must be kept away from
wet surfaces. ATTENTION: water must not touch the projector when it is
connected to the mains supply. To protect the unit from rain use the accessory
GOLIVE COVER.
9. MAINTENANCE - Before starting any maintenance work or cleaning the
projector, cut off power from the mains supply.
ATTENTION: According to guarantee conditions just the lamp substitution is
considered an allowed maintenance. If you need to replace the lamp, it is
recommended, after turning off the projector, to wait 15 minutes before
opening the cover to access the lamp. Now wait another 10 minutes before
touching the lamp to avoid burns. The product should never be washed, but
should be cleaned on the outside with only a slightly damp cloth. If a
replacement of other parts (engine, drive circuit or ballast, etc.) is needed
please contact your dealer in order to have more information as well as the
original parts. Not try to replace by themselves defective parts with not original
spare parts.
10. LAMP - Carefully read the "operating instructions" provided by the lamp
manufacturer. In order to know the supplied lamp please refer to the section
PACKAGE CONTENT of this manual. Immediately replace the lamp if damaged
or deformed by heat.
11. RISK OF VIEW - Never look the beam of the projector directly or with optical
instruments of convergence of the light.
12. RESIDUAL RISKS – Also if the product is built in compliance with all rules and
precautions, residual risks related to certain structural aspects of product usage
remain. Do not disassemble the device. Maintenance should be performed by
trained personnel. Do not tamper for any reason the ballast which is sealed for
safety reasons and should remain so. If ballast is tampered this represents a
serious danger and in this status the product is no more under warranty. Set
the unit in visible areas and pay attention that does not interfere with normal
passage of people, the risk of a collision must be minimized if not eliminated.
Do not place the unit in positions where it can fall hitting people or animals.
Keep children away from the unit when it is working and it is still connected to
the mains supply. In case of abnormalities in the coating or breakage of the
housing that contains bright spare parts, do not turn on the projector and stop
the use of the product. Do not install in areas available to minors or persons
Loading...