ECO SpotTM LED40C User Manual
Copyright © 2015 Sunhope Inc Page 1 of 4
Thank you for choosing our ECO Spot
TM
LED40C Gobo Projector (SKU:
ES-LED40C). This unit is equipped with a fan cooled 40W High Power LED.
Please read this manual before installing or operating this fixture, follow
the safety precautions listed below and observe all warnings.
Below is a general Gobo Changer description, please see the separate ECO Spot Gobo
Changer Manual for Details.
WARNING! Some models are equipped with a voltage selector switch on the back plate of the
unit. Select the correct Line Voltage with the selector on the back of the unit before Operating.
Package Contents
• Projector with power cord
• Test Gobos
• Integrated Gobo Mounts
• User Manual
Safety Information
• This product is not for household use, it presents risks of severe injury or death due to fire and burn
hazards, electric shock, lamp explosion and falls.
• Place your fixture at a suitable place with good air flow.
• Keep flammable materials away from the fixture.
• Minimum distance to flammable material = 1 ft (0.3m).
• Minimum distance to illuminated surface = 3.3 ft (1.0m).
• Provide a minimum clearance of 4 in (10cm) around air vents.
• Use only genuine spare parts for part replacement.
• Do not look directly into the lamp; it can result in eye damage.
• Don’t touch the hot surface during operation, use gloves if necessary.
• Always unplug the unit from the power mains before any service is done.
• Allow 20 minutes to cool down before servicing the unit.
• Replace Lamps only with the same type other lamps may cause damage.
• Light fixtures should be installed and maintained only by qualified personnel with experience in
lighting equipment and general electrical experience.
Electrical Safety
• Disconnect the fixture from AC power before handling the fixture.
ECO SpotTM LED40C User Manual
Copyright © 2015 Sunhope Inc Page 2 of 4
• Always ground (earth) the fixture electrically.
• Use only a power source that complies with local building and electrical codes and has both
overload and ground-fault protection.
• Do not use the fixture if the power cable or power plug is in any way damaged, defective or wet, or if
they show signs of overheating.
Handling Instructions
• Before the initial start-up, please unpack and carefully check for damage caused during
transportation.
• Place your fixture at a suitable place with good air flow.
• Make sure there are no flammable materials close to the lamp.
• When suspending the fixture above ground level, verify that the structure can hold at least 10 times
the weight of all installed devices.
• Verify that all external covers and rigging hardware are securely fastened and use an approved
means of secondary attachment such as a safety cable.
Warranty
One Year from Date of Purchase.
Focusing
• Power up the projector by pressing the larger switch in the back.
• Turn on the gobo rotator with the smaller switch in the back and switch it off when the gobo
projects in the desired position.
• Focus the projection by twisting the lens in and out until the image is well focused. When used for
the first time, the lens will often need to be twisted outwards many rotations to reach the focusing
point.
Lens Options
The projector accommodates interchangeable projection lenses to allow optimizing the projection size and
resulting brightness at varying distances. the more narrow the lens, the smaller and brighter the image will
be at a given distance.
Gobo Rotator
• The gobo rotator can be turned on/off with the push-button switch on the back plate.
• There are no controls for rotating speed or direction.
ECO SpotTM LED40C User Manual
Copyright © 2015 Sunhope Inc Page 3 of 4
Multi-functional Yoke
• The yoke can slide over the whole length of the fixture body to accommodate multiple pointing
directions.
• The yoke serves as stand.
• The yoke can be screwed to a wall or ceiling or fastened with a C-clamp.
Gobo Changer Functionality (see the Gobo Changer Manual for details)
The gobo changer has four gobo slots. A timer continuously switches between the different gobos.
Unless customized (see below), it will go a full sequence ( slot 1,2,3,4,1,2,...). Turn on and off the gobo
changer with the small switch on the back plate.
Interval Timer: The interval timer can be set by turning the knob on the back plate from continuous up to
approx. 120 seconds changing interval.
Single Gobo: For showing only a single gobo w/o any changes, simply turn off the changer power switch on
the back plate when the correct gobo shows.
Two or Three Gobos: For showing 2 or 3 gobos only. The
changer is equipped with four sensor magnets, one for each
gobo slot. For showing only three gobos, remove one
magnet. For two gobos, remove two magnets. Unscrew the
magnet with pliers.
Tip: Screw the removed magnet back in from the opposite
to keep it for later use.
Static Slot: The unit has an additional static slot, which can
be used in two ways:
• Color Overlay in conjunction with b/w gobos in
the changers Gobo Wheel and a color filter in the Static Slot.
• Gobo Color Changer in conjunction a b/w gobo
in the Static Slot and color filters in the changers Gobo
Wheel.
Specifications
Line Voltage (use the Line Voltage Selector in the back to select the correct line voltage.)
US/Canada Setting: 90-130V, 50-60Hz, 0.4A, 48W
International Setting (220V): 200-240V, 50Hz, 0.4A, 48W
Ambient Operating Temperature
-13 to 104°F (-25 to 40°C)
Gobo Dimensions
Metal or Glass Gobos and Dichroic filters
ECO SpotTM LED40C User Manual
Copyright © 2015 Sunhope Inc Page 4 of 4
Outer Diameter (OD): 37.5mm Max. Image Diameter (ID): 25mm
Max Thickness 4mm (0.16 in)
LED Lamp
The projector is equipped with a 40W LED lamp that is designed to work for the full lifetime of the projector.
There is no need for a replacement lamp.
- Extremely high light density for ultra-efficient projection.
- Bulb life: 50,000h - Color Temperature: 5,500K, +/-500K
- Rated Luminous Flux: 2,000lm - Effective Luminous flux: 1,100lm
Dimensions / Weight
Body wi t ho ut Yoke : 10in x 5.25in (254mm x 133mm) (L x D) The projection lens adds 0.5 to 2in (12 to
50mm) to the length.
Height with Yoke: 6in (127mm)
Weight: 8lbs (3.6kg)
Lens Options
The projector can be equipped with standard ECO Spot projection lenses.
A larger focal length (f) makes a smaller projection angle and therefore a smaller but brighter image.
Currently these lenses are available:
• Semi-Wide f=50mm 25
o
• Medium f=70mm 20
o
• Semi-Narrow f=100mm 15
o
Product Distributed by
Sunhope Inc
2750 14th Ave., Unit G12-13, Markham, ON, L3R 0B6
www.thegobo.com
Tel: (905)604-7080
Email: sales@thegobo.com
Loading...