Goblin IB70210 Instruction Manual

This guarantee is valid in the UK and Ireland

only. It is in your interest to retain the retailers receipt

as proof of purchase. Please quote the following information if the product develops a fault. These numbers can be found on the motor unit of the product.

Model No. Serial No.

(Please enter numbers for future reference)

All Goblin products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced.

If the fault develops after 28 days and within 24 months of original purchase, you should take the appliance to your nearest service agent. A list containing details of your nearest service agent is included with your appliance but please contact the helpline quoting Model number and Serial number should you require further assistance, repair or replacement of the product is subject to the following exclusions. (see Exclusions).

If you suspect a fault, follow the simple checks detailed below before returning the appliance or calling the helpline.

1 Check the dustbags and filters for blockages. 2 Check the hose and tubes for blockages. 3 Check the plug is firmly in the socket and the

supply is switched on. 4 Make sure the socket is working by trying

another appliance.

To qualify for the 2 year parts and labour guarantee the appliance must have been used according to the manufacturers instructions.

EXCLUSIONS

Goblin shall not be liable to replace or repair the goods under the terms of the Guarantee where: 1 The fault has been caused or is attributable to

accidental use, misuse, negligent use or used

contrary to the manufacturers recommendations

or where the fault has been caused by power

surges or damage caused in transit. 2 The appliance has been used on a voltage

supply other than that stamped on the

products. 3 Repairs have been attempted by persons other

than our service staff (or authorised dealer). 4 Where the appliance has been used for hire

purposes or non-domestic use. 5 The guarantee excludes consumables such as

bags, filters and air freshners.

This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer.

If for any reason this item is replaced during the 2 year guarantee period, the guarantee on the new item will be calculated from original purchase date. Therefore it is vital to retain your original till receipt or invoice to indicate the date of initial purchase.

The After Sales Division, Goblin, Mexborough, South Yorkshire, England, S64 8AJ HELPLINE (OFFICE HOURS ): UK (LOCAL RA TE) 0345 010340, REPUBLIC OF IRELAND DIMPCO LTD 01 842 4833

Wet and Dry vacuum cleaner

2 year parts and labour guarantee

Instruction Manual

Important SafeguardsImportant Safeguards

Important Safeguards

This product has been designed with your safety in mind. However, for safe operation, it is important that you observe the following points:

1 Read all the instructions. 2 To obtain best results from your

cleaner please read these instructions

carefully and keep them in a safe

place. 3 This product conforms to the relevant

safety regulations for electrical appliances. 4 Never use the appliance without the foam

pre filter and motor protection panel filter

installed. 5 Use only genuine Goblin spare parts and

accessories. 6 If the electrical cable becomes damaged the

complete cable assembly must be replaced.

Do not attempt this task yourself, contact

Goblin using the helpline number on the

front of this leaflet. 7 Never use this appliance to vacuumhot

ashes, hot cigarette ends, hot coals or

other similar items. 8 Never use in the presence of explosive

liquids or vapours. 9 Never pick up inflammable or poisonous

liquids such as petrol, copier toner, or other

volatile substances. 10 Never pick up acids, asbestos or asbestos

dust. 11 Do not store the appliance near hot ovens

or heating appliances. 12 The appliance should never be left running

unsupervised. 13 Children do not understand the dangers

associated with operating electrical

appliances. Never allow children to use this

appliance. 14 Always disconnect the appliance from the

mains supply after use or prior to cleaning

or replacing dust bags or filters.

SAVE THESESAVE THESE

SAVE THESE INSTRUCTIONSINSTRUCTIONS

INSTRUCTIONSINSTRUCTIONS

INSTRUCTIONS

15 Do not use or keep this product outside

when it is raining.

16 Never modify the cleaner in any way. 17 Repairs to electrical appliances are only to

be undertaken by authorised service agents. Unprofessional repairs can be dangerous for users.

18 This vacuum cleaner is intended for

domestic use only. Misuse or use for commercial or any other purpose will render the guarantee invalid.

Electrical requirementsElectrical requirements

Electrical requirements

When using this appliance outdoors it should be additionally protected by a RCCB (Residual Current Circuit Breaker).

Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A.C. (Alternating current).

For appliances with fitted plug.

If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted.

IMP0RT ANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET .

Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted.

For models with cable rewind

If you cut the plug off and let go of the cable it will rewind into the machine. Therefore you must pull out a length of cable and secure it BEFORE cutting off the plug and refitting a new one.

Electrical connection and supplyElectrical connection and supply

Electrical connection and supply

European conformity informationEuropean conformity information

European conformity information

A sample of this product has been tested and found to be in conformity with the following

European Directives. 73/23/EEC Low voltage

93/68/EEC CE Marking 89/336/EEC EMC directive

Check that the supply voltage details given on the rating plate are in accordance with your electricity supply.

IMPORTANT :The wires in the mains lead of this appliance are coloured in accordance with the following code : Blue-Neutral, BrownLive. As the colours of the wires in the mains lead of this appliance may not correspond with the markings identifying the terminals in your plug proceed as follows,

The wire which is coloured brown must be connected to the terminal which is marked with the letter ‘L’ or is coloured red.

The wire which is coloured blue must be connected to the terminal which is marked with the letter ‘N’ or is coloured black.

This appliance is double insulated and must not be connected to the terminal of the plug which may be marked with the letter ‘E’ or by the earth wire symbol or coloured green or green and yellow. Each wire must be properly connected to the appropriate terminal pin of a suitable plug and the outer sheath of the mains lead securely retained by the anchorage arrangements of the plug. In case of doubt the plug should be fitted by a qualified electrician or competent person as the guarantee offered on this product does not cover any fault in the plug or damage caused to the appliance as a result.

(If a fused 3-pin 13A plug is used a standard 13A fuse should be fitted).

FeaturesFeatures

Features

Motor unit Motor protection panel filter drawer Motor protection panel filter Cord wrap hook Filter condition indicator Carrying handle Exhaust filter frame Exhaust filter Automatic cord rewind (certain models) Hose inlet Float Latches Foam pre-filter On/off switch Inner tank (certain models)

Main tank Paper bag location slots (on main and inner tank)

Tool storage area

Hose handle

Air bleed

Extension tubes

(plastic or metal depending on the model)

Hose swivel connector

Paper bag (certain models)

Paper bag holder (certain models)

Wet pick up nozzle with inserts brush and squeegee (certain models)

Floor nozzle

Upholstery nozzle (certain models) Crevice tool (certain models)

Your vacuum cleaner may feature a removable inner tank and large capacity paper bag and can be operated in a variety of ways detailed in the table below.

Dry usage - vacuuming fine or coarse dry dirt. Wet usage - picking up liquids or wet dirt, ie leaves.

Using your vacuum cleanerUsing your vacuum cleaner

Using your vacuum cleaner

Pick up option 1 Main tank only

2 Inner tank fitted

3 Paper bag fitted

Usage

Dry and / or Wet

Dry Only

No liquids or wet dirt

Application

Maximum capacity .

RECOMMENDED METHOD FOR GENERAL USE.

Hygenic dirt disposal.

AssemblyAssembly

Assembly

Option 1 Using the main tank only

1 Release the latches and lift off the motor

unit .

2 Remove the inner tank if fitted. 3 Replace the motor unit and ensure the latches

are secure.

Option 2 Inner tank fitted

1 Ensure the latches are secure.

Option 3 Paper bag 23 fitted

The paper bag can be fitted with or without the inner tank in place.

1 Release the latches and lift off the motor

unit . 2 Slide the card collar on the paper bag

into

the bag holder 24 and fit into the location slots

on the main or inner tank.

3 Replace the motor unit and ensure the latches

are secure.

AccessoriesAccessories

Accessories

Hose 1 Push and rotate the elbow-shaped

connector on the end of the hose

into the hose inlet until it clicks into

position Hose features a 360

swivel action for

improved manoeuvrability.

Extension tubes 1 For normal vacuuming join the two

tubes together

2 Attach the two tubes to the handle .

Some tasks may be easier with only

one tube fitted.

T ools

The tools can be attached to the tube or directly to the handle.

Floor nozzle

General purpose tool that can be used on a variety of floor coverings.

Upholstery nozzle

Nozzle can be used for curtains, sofas and armchairs.

Wet pick up nozzle with inserts, brush and squeegee.

Suitable for outdoor and wet usage.

Crevice tool

Used for small gaps, joints and corners.

On board storageOn board storage

On board storage

Your vacuum cleaner has on board storage facility for hose, tubes and tools. Wrap hose around the tool storage area and position hose handle in location provided.

OperationOperation

Operation

If your cleaner features the automatic cable rewind pull out the cable fully.

If your cleaner features cable wrap ensure the cable is fully unwrapped.

Plug into the electrical socket.

Switching on

Switch the cleaner on using the on/off button

Controlling suction power

To reduce the suction power during use, adjust the air bleed 20 on the hose handle 19.

Closed :full suction Open :low suction

Note: When the task is to suck up a large quantity of liquid, best results are achieved if the air bleed is opened slightly.

Motor safety shut off

When the waste tank is full of liquid the float will automatically switch off the motor. When this occurs, always:

• Switch off the machine as it may restart if you lift the motor unit from the tank.

• Disconnect from the electrical supply by removing the plug from the wall socket.

• Raise hose to drain liquid back into the tank.

• Empty the main tank or inner tank.

IMPORT ANT

If the cleaner overturns during use, the motor may switch off. Return the cleaner to upright and motor will restart.

After vacuum cleaningAfter vacuum cleaning

After vacuum cleaning

1 Switch off the vacuum cleaner. 2 Unplug from the mains. 3 Use a hand or your foot to operate the

cable rewind pedal to rewind the cable.(on certain models)

IMPORT ANT

For safety reasons the final section of cable rewinds slowly. Lift the plug to ensure the cable rewinds fully.

4 For models without the cable rewind

facility wind the cable around the hose storage area and cable wrap hook at the rear of the unit.

Emptying your vacuumEmptying your vacuum

Emptying your vacuum cleanercleaner

cleanercleaner

cleaner

Option 1 Using the Main tank only

1 Release the latches and lift off the

motor unit and carefully place to one side.

2 Carefully lift the main tank and empty. 3 Rinse or clean the main tank after

emptying if necessary.

Option 2 Inner tank fitted

1 Release the latches and lift off the

motor unit and carefully place to one side.

2 Carefully lift out the inner tank by its

rotating handle and empty.

3 Rinse or clean the inner tank after

emptying if necessary.

Option 3 Paper bag 23 fitted

1 Release the latches and lift off the

motor unit and carefully place to one side.

2 Gripping the bag holder

lift the bag

out of the main or inner tank.

3 Slide the bag off the holder 24 and

carefully dispose of the bag.

After each option replace the motor unit and ensure the latches are secured.

FiltersFilters

Filters

Your product has been designed to pick up both wet and dry dirt without having to change or remove the filters.

The table below explains the purpose of each filter.

Filter

Foam pre-filter (washable)

Motor protection panel filter

Exhaust filter (non washable)

Purpose

Stops large dirt particles and

prolongs the life of the panel filter .

Stops smaller dust particles and

protects the motor from damage.

Stops very fine dust particles to ensure the air leaving the product is clean.

IMPORT ANT

• The motor protection panel filter should be checked regularly for signs of damage, preferably after each cleaning task. The filter must be replaced immediately if it has become damaged.

• Always disconnect the cleaner from the mains when checking filters.

• Always make sure all filters are fitted before use. Failure to do so may result in

damage to your product.

T o clean the foam pre-filter

1 Unclip and remove the motor unit. 2 Turn the motor unit over. 3 Remove and clean the filter using

a soft brush or wash in warm soapy water.

4 Ensure the filter is totally dry before

refitting.

5 Make sure it is secure on its two clips.

T o clean the motor protection panel filter

1 Slide open the drawer at the rear of

cleaner.

2 Remove filter and clean between

lower pleats with a soft brush.

IMPORT ANT

The filters should be replaced at least every 6 months or immediately if they become damaged.

T o clean the exhaust filter

1 Pull out the exhaust frame . 2 Remove the filter and tap to remove

the dirt.

Cleaning the filtersCleaning the filters

Cleaning the filters

If the filter condition indicator shows red either the :

• bag needs to be changed

• foam pre-filter needs to be cleaned

• motor protection panel filter needs to be cleaned

• Also check hose for blockages

If after changing the bag or cleaning the filters the condition indicator still shows red then the filters should be replaced.

Cleaning andCleaning and

Cleaning and MaintenanceMaintenance

MaintenanceMaintenance

Maintenance

Unplug from the mains before cleaning. The vacuum cleaner, and all the acces-

sories can be cleaned using a damp cloth or a non abrasive domestic cleaner and wiped dry.

To keep the underside of the floor nozzle clean, vacuum it at regular intervals using the crevice tool.

Purchasing new dustPurchasing new dust

Purchasing new dust bags and filtersbags and filters

bags and filtersbags and filters

bags and filters

Only use original Goblin bags and filters. Replacement packs can be purchased from specialist retailers. If you have difficulty, call our Helpline number on the front of this booklet.

If none of the above solutions resolve the problem, please contact your nearest service agent or telephone the helpline at the front of this booklet.

PROBLEM

The cleaner does not start

Reduced suction power/ filter condition indicator

shows red

Dust expelled from air exhaust during use

Water expelled from air exhaust during use

Hose detached from product during use

Intermittent on/off switching

POSSIBLE CAUSE

No electricity supply

Hose, nozzle or filter blocked

Filter is not fitted correctly, is damaged or is missing altogether

Float is damaged or clogged

Hose not fitted correctly

Waste tank is full

SOLUTION

Check fuse, cable, plug and socket, if necessary have them replaced by a

qualified technician.

Remove blockages and refit hose or nozzle / check filters.

Refit or replace filter.

Remove any blockage and restart. If float is damaged then contact service agent.

Refit hose following instructions carefully.

Switch off product and empty.

Goblin products are intended for non commercial use only.

Goblin has a policy of continuous improvement in product quality and design.

The Company, therefore, reserves the right to change the specification of its models at any time.

Goblin, Mexborough, South Y orkshire, England, S64 8AJ

8738170 Rev OI

Consumables new Wet and dry UKConsumables new Wet and dry UK

Consumables new Wet and dry UK

Accessory

A/v Goblin dustbags (pack of 3) Bag holder A/v panel filter + foam pre-filter + standard

exhaust filter in one box Floor nozzle Hard floor attachment for floor nozzle Wet pick up nozzle Squeegee insert Brush insert Crevice tool Upholstery nozzle Plastic tubes Metal tubes Telescopic tubes Flexible hose and handle assembly

Part number

9050475 1781434 9030075

0073534 0073690 7870434 7930271 7924868 0310234 0070834 3770234 3770570 3779870 5330975

UK (local rate call) 0345 010340 The After Sales Division Goblin Mexborough South Yorkshire S64 8AJ

Republic of Ireland 01 842 4833 The After Sales Division Dimpco Ltd Cloghran County Dublin Ireland

If you experience any difficulty in obtaining service or spare parts, please telephone our Customer Helpline (during office hours):

Goblin IB70210 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual