GOBLIN 380 KYLE STACY EDITION
SAB HELI DIVISIONSAB HELI DIVISION
- Carefully check your model before
each flight to ensure it is airworthy.
- Consider flying only in areas
dedicated to the use of
model helicopters.
- Check and inspect the flying
area to ensure it is clear of
people orbstacles.
- Rotor blades can rotate at very
high speeds! Be aware of the
danger they pose.
- Always keep the model at a
safe distance from other pilots
and spectators.
- Avoid maneuvers with trajectories
towards a crowd.
- Always maintain a safe distance
from the model.
Goblin 380 Kyle Stacy Manual
Release 1.0 - November 2015
WORLD DISTRIBUTION
www.goblin-helicopter.com
For sales inquiries, please email:
sales@goblin-helicopter.com
For information, please email:
support@goblin-helicopter.com
Attention: If you are a consumer and have questions or need of assistance,
please contact the retailer where you made the purchased first.
EUROPEAN DISTRIBUTION
www.sabitaly.it
For sales inquiries, please email:
sales@sabitaly.it
For information, please email:
info@sabitaly.it
Attention: If you are a consumer and have questions or need of assistance,
please contact the retailer where you made the purchased first.
225mm
764mm
SPECIFICATIONS
It is extremely important that you take a moment to register your helicopter with us. This is the only way to ensure that you are
properly informed about changes to your kit, such as upgrades, retrofits and other important developments. SAB Heli Division
cannot be held responsible for issues arising with your model and will not provide support unless you register your serial
number.
To mount the serial number tag on your helicopter, please refer to page 7.
Thank you for your purchase, we hope you enjoy your new Goblin helicopter!
SAB Heli Division
VERY IMPORTANT
Inside Box 4, you will find Bag 19. This bag contains your serial number tag. Please take a moment to register your kit online
via our web site at:
Main rotor diameter : 820mm.
Main blade length : 360mm.
Tail rotor diameter : 192mm.
Tail blade length : 70mm.
Main shaft diameter : 8mm.
Tail shaft diameter : 5mm.
Spindle diameter : 5mm.
Motor size: Maximum 41mm diameter, maximum height 41mm.
Battery compartment: 44x44x130mm.
http:
//www.goblin-helicopter.com
13 – Tail Assembly
14 – Installation of the Boom, Canopy
15 – Battery
16 – In flight
17 – Maintenance
18 – Exploded Views
19 – Spare Parts
INDEX
1 – Specifications
2 – Important Notes
3 – Components and Box
4 – Carbon frame Assembly
5 – Transmission Assembly
6 – Main Rotor Assembly
7 – Assembling The Modules
8 – Installation of Swashplate Servos
9 – Tail Servo Assembly
10 – Installation of The Motor
11 – Installation of The ESC
12 – Installation of Flybarless Unit and RX
Page 1
Chapter 1, Specifications
Use CA Glue
Use Proper
Lubricant
Indicates that for this
assembly phase you need
materials that are in Bag xx.
Bag xx
Use retaining
compound
(eg Loctite 243)
Use retaining
compound
(eg Loctite 648)
Important
NOTES FOR ASSEMBLY
Please refer to this manual for assembly instructions for this model.
Follow the order of assembly indicated. The instructions are divided into chapters, which are structured in a way that
each step is based on the work done in the previous step. Changing the order of assembly may result in additional or
unnecessary steps.
Use thread lockers and retaining compounds as indicated. In general, each bolt or screw that engages with a metal part
requires thread lock.
It is necessary to pay attention to the symbols listed below:
IMPORTANT NOTES
*This radio controlled helicopter is not a toy.
*This radio controlled helicopter can be very dangerous.
*This radio controlled helicopter is a technically complex device which has to be built and handled very carefully.
*This radio controlled helicopter must be built following these instructions. This manual provides the necessary information
to correctly assemble the model. It is necessary to carefully follow all the instructions.
*Inexperienced pilots must be monitored by expert pilots.
*All operators must wear safety glasses and take appropriate safety precautions.
*A radio controlled helicopter must only be used in open spaces without obstacles, and far enough from people to minimize
the possibility of accidents or of injury to property or persons.
*A radio controlled helicopter can behave in an unexpected manner, causing loss of control of the model, making it very
dangerous.
*Lack of care with assembly or maintenance can result in an unreliable and dangerous model.
*
Neither SAB Heli Division nor its agents have any control over the assembly, maintenance and use of this product.
Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release SAB Heli Division from
any responsibility or liability arising from the use of this product.
SAFETY GUIDELINES
*Fly only in areas dedicated to the use of model helicopters.
*Follow all control procedures for the radio frequency system.
*It is necessary that you know your radio system well. Check all functions of the transmitter before every flight.
*The blades of the model rotate at a very high speed; be aware of the danger they pose and the damage they may cause.
*Never fly in the vicinity of other people.
Page 2
Chapter 2, Important Notes
Inside the main box there are:
Inside the main box:
Box 1: Canopy.
Frames.
Blade Holder.
Landing Gear.
Battery Support.
Tail Fin Assembly.
Box 2: Combo Components (Optional).
Box 3: Boom.
Carbon Rod.
Blades + Tail Blades.
Box 4: Mechanical parts, Bags.
TOOLS, LUBRICANTS, ADHESIVES
*Generic pliers.
*Hexagonal driver, size 1.5,2,2.5mm.
*5.5mm Socket wrench (for M3 nuts).
*7mm Hex fork wrench (for M4 nuts).
*Medium threadlocker (eg. Loctite 243).
*Strong retaining compound (eg. Loctite 648).
*Spray lubricant (eg. Try-Flow Oil).
*Grease ( eg. Microlube GL261 ).
*Cyanoacrylate adhesive.
*Pitch Gauge (for set-up).
*Soldering equipment (for motor and ESC wiring).
The assembly process is described in the following chapters. Each chapter
provides you with the box and bag you will need for that chapter.
The information is printed at the top of every page.
ADDITIONAL COMPONENTS REQUIRED
*Electric Motor: 850 - 1000Kv:
Maximum diameter 41mm.
Maximum height 41mm.
Pinion shaft diameter 5 mm.
*Speed controller: minimum 60A , extreme 3D Flight 70-90A.
*Batteries: 6S-1800 mAh ( 1500 - 2600 mAh ) .
*1 flybarless 3 axis control unit.
*Radio power system, if not integrated with the ESC.
*3 micro cyclic servos.
*1
mini (midi)
tail rotor servo.
*6 channel radio control system on 2.4 GHz.
(See configuration examples on page 14).
Manual
BOX 1
BOX 2
BOX 4 BOX 3
MAIN BOX
Page 3
Chapter 3, Components and Box
4-Carbon Frame
The manufacturing process of the carbon parts
often leaves micro-burrs and sharp edges. We
recommend de-burring the edges to minimize the
risks of electrical wire cuts, etc.
This is particularly
important in the areas shown in red.
Page 4
Chapter 4, Carbon Frame
Left Main Frame Assembly
Note:
Box 1, Bag 1
Button Head Cap
Special M2.5x6mm
(HC019-S)
Plastic Battery
Support
(H0529-S)
Tail Servo
Support
(H0530-S)
Button Head Cap
Special M2.5x6mm
(HC019-S)
Button Head Cap
Special M2.5x6mm
(HC019-S)
Main Frame
(H0531-S)
Main Frame
(H0531-S)
Button Head Cap
Screw M2x5mm
(HC005-S)
Battery
Alu Block
(H0539-S)
Use Loctite 243 to
lock the bolts in the
correct position.
Main Frame Assembly
SUGGESTION
If you have the tail servo, we
suggest you install it at this time as
it will be more convenient to do so
before assembling the main frames.
Please refer to page 13 now for
more information.
Button Head Cap
Special M2.5x6mm
(HC019-S)
Button Head Cap
Special M2.5x6mm
(HC019-S)
Note:
Use Loctite 243 to
lock the bolts in the
correct position.
Page 5
Chapter 4, Carbon Frame
Lading Gear Assembly
Bag 1, Box 1
Main Frame
Assembly
Alu Landing
Gear Support
(H0644-S)
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Finishing
Washer M2.5
(H0255-S)
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Plastic Landing
Gear Support
(H0556-S)
Head Cap Screws
Special M2.5x6mm
(HC019-S)
Carbon Fiber
Landing Gear
(H0645-S)
Page 6
Chapter 4, Carbon Frame
Bag 2, Bag 19
Main Shaft Support Assembly
Main Shaft Support
(H0522-S)
Bearing Ø8xØ16x5mm
(HC419-S)
Main Shaft Support
Assembly
Main Shaft
(H0507-S)
Bearing Ø8xØ16x5mm
(HC419-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Main Shaft Assembly
Main Shaft
Assembly
Main Plate
(H0519-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Shims Ø8xØ12x0,1mm
(HC462-S)
Tighten the three screw M2.5.
After tightening, check the
axial play of the main shaft. It
is possible to reduce any axial
play by adding shims.
IMPORTANT:
Very carefully
check to make sure you can
turn the main shaft freely.
If you feel too much friction,
you have used too many
shims, you can remove a shim
until the shaft turns freely.
Serial Number
[Bag 19]
Page 7
Chapter 5, Transmission Assembly
Socket Head Cap
Screw M2x8mm
(HC008-S)
One Way Bearing
Ø8xØ12x12mm
(HC440-S)
120T Pulley
(H0502-S)
Plastic Servo Support
(H0548-S)
Flanged Bearing
Ø8xØ12x3,5
(HC418-S)
Add or remove shims to get
approximately 0.2-0.4mm play.
eg: Microlube GL261
Bag 3
Socket Head Cap Screw
M2.5x18mm
(HC032-S)
Main Plate
Assembly
Flanged Bearing
Ø8xØ12x3,5mm
(HC418-S)
120T Pulley Assembly
(H0502-S)
Front Tail Pulley Assembly
(H0503-S)
Front Tail
Pulley
(H0503-S)
Front Tail Pulley
Assembly
120T Pulley
Assembly
Shims
Ø8xØ14x0,2mm
(HC228-S)
Socket Head Cap
Shoulder M2.5x15mm
(HC031-S)
Note:
Anti-Rotation
(H0533-S)
Socket Head Cap
Screw M2.5x6
(HC018-S)
Socket Head Cap
Screw M2x5
(HC002-S)
Page 8
Chapter 5, Transmission Assembly
Approx 45 mm
11mm
Linkage Rod A Assembly . . . .x3
(Initial length for the rods from the
swashplate to the Blade Grip.)
Blade Grip Linkage Assembly
Head Cap
Screw M2.5x15mm
(HC028-S)
Flanged Bearing
2.5x
6x2.5
(HC400-S)
Bushing
[H0599]
Blade Grip Linkage
(H0598-S)
Linkage Rod
(H0561-S)
Plastic Ball Link
(H0403-S)
Center Hub Assembly
Center Hub
(H0595-S)
Spindle
(H0596-S)
HEX 2.5 Inside
eg: Microlube GL261
Blade Grip Assembly
Head Cap
Screw M2.5x8mm
(HC020-S)
Bearing
5x
10x4mm
(HC411-S)
Blade Grip Arm
(H0597-S)
Main Blade Grip
(H0513-S)
Washer
7.5x
10x0.5
(H0349-S)
Thrust Bearing
5x
10x4mm
(HC435-S)
Blade Grip Linkage
Assembly
Blade Grip
Assembly
C Washer
5x
7x0.2mm
(HC449-S)
[HC449-S]
[H0513-S][H0595-S]
Bearing
5x
10x4mm
(HC411-S)
Button Head Cap
Screw M4x6mm
(HC096-S)
Note
: Larger ID Inside
Bag 4
Note:
Page 9
Chapter 6, Main Rotor Assembly
12 mm
Socket Head Cap
Shouldered M3x16mm
(HC074-S)
Swashplate
Assembly
Button Head Cap
Special M2.5x6mm
(HC019-S)
Head Assembly
Cup Point Set
Screws M4x20mm
(HC155-S)
Bag 5
Metric Hex
Nylon Nuts M3
(HC206-S)
Canopy Positioner
(H0542-S)
NOTE:
Keep the distance between the end of the canopy retainer
H0542 and the frame at approximately 12mm.
Button Head Cap
Special M2.5x6mm
(HC019-S)
Cup Point Set
Screws M4x20mm
(HC155-S)
Uniball M2
(H0538-S)
Swashplate Assemly
Uniball M2
(H0537-S)
Uniball M2
(H0538-S)
Swashplate
Assemly
(H0600-S)
Page 10
Chapter 7, Assembling The Modules
13-15mm
Servo 1
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Uniball M2
(H0538-S)
INSTALLATION OF SWASHPLATE SERVOS
The linkage ball must be positioned approximately
13-15 mm
out on the servo arm (
figure 1
), it is recommended to use the SAB
servo arm p/n [HA052]. Because of the 120° placement of the servos in the Goblin, the arms are difficult to access. For this reason
it is advisable to ensure alignment of the servo arms (and sub trim) before installation of the servos in the model
(figure 2).
Proceed with installation following the instructions below
. Figure 3
shows a completed installation.
The rods going from the servos to the swash plate must be as vertical as possible. ( Red line in Figure 4 )
Not all servos are equal,
so for proper alignment you can choose to use the supplied
spacer H0566 under the uniball H0538.
Bag 6
Servo 2
Servo 2
Button Head Cap
Screw M2x5mm
(HC005-S)
SAB Servo Arm
(HA052-S) ( Option)
Servo 3
Button Head Cap
Screw M2x5mm
(HC005-S)
Note:
Do not over tighten,
be careful to not strip plastic.
Note:
Do not over tighten,
be careful to not strip plastic.
Page 11
Chapter 8, Installation Of Swashplate Servos
Initial length for the rods from the swashplate
to the blade grips.
Linkage Servo
(H0524-S)
HPS Head Preliminary Setup
Tip on cable routing
Linkage Rod A
Aseembly
Linkage Rod A Assembly ... x2
Linkage Rod M2x22mm
(H0561-S)
Approx 45mm
You can use zip-ties to secure the 3
servo cables to the servo support.
Page 12
Chapter 8, Installation Of Swashplate Servos
14 mm
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
The distance between the
servo spline
and the ball must be between 13-15 mm
You can use the SAB servo horn [HA053].
Uniball M2
5H6
(H0064-S)
Socket Head
Cap M2x8mm
(HC008-S)
Tail Servo
Bag 6
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Servo Spacer
(H0572-S)
Servo Spacer
(H0572-S)
Socket Head Cap M3x6mm
(HC044-S)
Chapter 9, Tail Servo Assembly
Page 13
12.5
.........................................................................................................................
........................................................................................................................
........................................................................................................................
.........................................................................................................................
.........................................................................................................................
.........................................................................................................................
.........................................................................................................................
.........................................................................................................................
Some example configurations:
TRANSMISSION SETUP
It is important to choose the right reduction ratio to maximize efficiency based on your required flight performance.
It is possible to optimize any motor and battery combination.
It is recommended to use wiring and connectors appropriate for the currents generated in a helicopter of this class.
If you are using a head speed calculator which requires a main gear and pinion tooth count, use
120
teeth for the main gear and
the tooth count of your pulley as the pinion count.
Below is a list of available reduction ratios:
H0501-19-S - 19T Pinion = ratio 6.3:1 H0501-22-S - 22T Pinion = ratio 5.5:1
H0501-20-S - 20T Pinion = ratio 6:1 H0501-23-S - 23T Pinion = ratio 5.2:1
H0501-21-S - 21T Pinion = ratio 5.7:1 H0501-24-S - 24T Pinion = ratio 5:1
The Goblin 380 accepts a wide selection of batteries with different capacities. The suggested number of cells is 6.
All batteries from 1500 to 2600 mAh offer good performance.
We recommend the use of an 1800 mAh battery for the perfect compromise between weight and performance (3D flight).
Larger capacity batteries (2200-2600) increase flight times at the expense of weight and reduced agility (Sport flight).
CONFIGURATION
Motor ESC Motor Pulley RPM Max Pitch
Quantum
2820-880
Scorpion
HK 3014-900
X-NOVA
2820-890
Scorpion
HK 3020-1000
KDE
500XF 925-G3
X-NOVA
3215-930
CC Lite 75 22T 3000
20T 3000
CC Lite 75 22T 3100
20T 3100
CC Lite 75 23T 3200
18T-
19T
3200-
3350
CC Lite 75 21T-
22T
3200-
3350
21T 3200
19T-
20T
3350-
3500
CC Lite 100 21T-
22T
3300-
3450
CC Lite 75 22T-
23T
3200-
3350
20T-
21T
3200-
3350
CC Lite 100 23T-
24T
3350-
3500
21T-
22T
3350-
3500
12.5
12.5
12.5
12.5
.........................................................................................................................
Note: Although the Goblin can handle even higher RPMs, for safety reasons we suggest to not exceed 3400 RPM.
Kontronik
Pyro 380-9
HW 100 - Koby 90 - YGE 90
HW 60 - Koby 70 - YGE 60
HW 60 - Koby 70 - YGE 60
HW 60 - Koby 70 - YGE 60
HW 60 - Koby 70 - YGE 60
HW 100 - Koby 90 - YGE 90
HW 60 - Koby 70 - YGE 60
Page 14
Chapter 10, Installation Of The Motor
22 mm
6mm
18.5 mm
(see page 14 for optional
pulleys)
Motor
Motor Support
(H0520-S)
Motor Pulley 21T
(H0501-21-S)
NOTE:
Bag 7
Flat Head Socket
Cap M3x5mm
(HC132-S)
Cone Point Set
Screws M3x6mm
(HC144-S)
Socket Head Cap
Screws M2.5x8mm
(HC020-S)
Washer
4.3x
11x1mm
(HC184-S)
Metrix Hex
Nylon Nut M4
(HC212-S)
Cone Point Set
Screws M4x12mm
(HC156-S)
Socket Head Cap
Screws M2.5x8mm
(HC020-S)
Finishing Washer M2.5
(H0255-S)
Finishing Washer M2.5
(H0255-S)
NOTE:
Correct position for the motor wires.
To maximize space for the batteries, it is
advisable to shorten the motor shaft.
Follow the dimensions given in this drawing.
For the cut, you can use an electric tool like a
“Dremel” with a cutoff disc.
Additionally, ensure the motor shaft has an
appropriate 'flat' for one of the set screws.
Page 15
Chapter 10, Installation Of The Motor
0.75 mm 0.75 mm
1.5 mm
Belt 304-2GT-09
(HC454-S)
MOTOR BELT TENSION
*Assemble the motor and pulley to its mounting plate.
*Install the motor assembly in the helicopter.
*It is easy to install the belt with the motor assembly pushed back towards the helicopter as far as it can go.
First put the belt on the motor pulley.
*Then put the belt around the big pulley.
*Rotate the motor several times by hand.
*Pull and hold the motor slightly.
*Tighten the M4 nut first (It is suggested to use tool nut driver).
*The belt must be very tight.
*Tighten the rest of the bolts.
Motor Assembly
Note:
Check for vertical alignment of the motor pulley. To do this, simply turn the motor several times by hand and check to you see if
the belt is aligned properly with the big pulley (one way bearing pulley).
If the belt is riding too high, simply loosen up the motor pulley and drop it just a little bit, if it is riding too low, loosen up the
motor pulley and raise it a bit.
Correct
Incorrect
Bag 8
Page 16
Chapter 10, Installation Of The Motor
100 mm
Figure 4:
Shows the suggested length of the battery wire. This length is also compatible with the quick battery connector upgrade.
Figure 5
: Shows the wire that connects the ESC to the receiver or flybarless control system.
DE-BURR THE SIDE FRAMES
We recommend de-burring the edges of the carbon parts in areas where electrical wires run.(See Page 4).
ESC INSTALLATION
The speed controller (ESC) is installed in the front of the helicopter.
Figure 1
and
Figure 2
show the mounting area.
Figure 3:
Shows the correct use of the Zip-Ties
Page 17
Chapter 11, Installation Of The ESC
1
5
4
2
3
Fig. 2 shows the unit mounted on the support H0564.
Fig. 3 shows the unit directly mounted on the main aluminum plate.
Use your judgment to decide whether you need to install your FBL unit as shown in Fig 2 or
Fig 3. This will depend on the size of the FBL unit itself and the arrangement of the wires.
With larger units, the nylon nut can make it difficult to connect the wires to the unit, in this
case it is recommended to use the aluminum support H0564.
With smaller units, the unit can be installed directly onto the main plate.
This facilitates boom removal in the future if necessary.
We recommend using some type of adhesive to prevent the servo wires and connections
from coming unplugged from the receiver or FBL unit. You can use hot glue for this purpose.
FBL Unit
Doublesided Tape
Bag 9
FLYBARLESS CONTROL UNIT AND RX INSTALLATION
We suggest the use of a “single unit” FBL system (all in one type unit).
This allows for easier wire routing considering the small size of this helicopter.
Position 1 can be used to install the FBL unit.
Position 2 and 3 can be used to install a small RX unit, like a Spektrum satellite.
Position 4 and 5 can be used to install RX unit.
FBL
Support
(H0564-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Page 18
Chapter 12, Installation Of Flybarless Unit and RX
The area between the boom and the frame can be used to route the wire(s) (Fig 4 and 5).
You can secure the wire(s) to the frame with zip-ties (Fig6).
Page 19
Chapter 12, Installation Of Flybarless Unit and RX
Note:
Larger ID inside
Tail Blade Grip
(H0511-S)
Flanged Bearing
7x
11x3mm
(HC416-S)
Tail Pitch Slider 02
[H0232]
Tail Pitch Slider 03
(H0512-S)
Tail Pitch Slider Assembly
Tail Damper
(H0567-S)
Tail Shaft
(H0509-S)
Tail Rotor Hub Assembly
Spacer
2x
4.5x0.5
(H0566-S)
Thrust Bearing
3x
6x2.5
(HC448-S)
Bearing
3x
6x2.5
(HC457-S)
Uniball M3
(H0065-S)
Washer
4.5x
5.9x0.5
(H0541-S)
Socket Head Cap
Screw M2x6mm
(HC004-S)
Spacer
2x
3x3mm
(H0076-S)
Note:
S >> Left Side
Note:
S >> Right Side
Note:
It is normal for the tail
to feel a bit tight after initial
assembly as the tail spindle preload is usually high when
the helicopter is brand new. The preload will loosen up
after 2-5 flights allowing the system to become smooth.
Bag 10
eg: Microlube GL261
Tail Spindle
(H0510-S)
Tail Pitch Slider 01
[H0231]
Flanged Bearing
7x
11x3mm
(HC416-S)
Bearing
3x
7x3
(HC458-S)
Washer
3x
4.75x0.5
(H0540-S)
Tail Rotor Hub
Assembly
Socket Head Cap
Screw M2x6mm
(HC004-S)
Tail Pitch Slider Link Assembly
Tail Pitch Slider Link
Assembly
Tail Pitch Slider Link
(H0261-S)
Tail Pitch Slider
Assembly
Spacer
2x
3x3mm
(H0076-S)
Page 20
Chapter 13, Tail Assembly
Flanged Bearing
5x
13x4mm
(HC412-S)
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Tail Side Plate Assembly
Socket Head Cap
Screw M2.5x18mm
(HC032-S)
Set Screw
M3x6mm
(HC144-S)
Note: The set screw should align
with the hole in the tail shaft.
Bag 11
Bell Crank Lever
(H0234-S)
Uniball
M3x
4 H3
(H0279-S)
Spacer Arm
2.5x
4x6.3mm
(H0253-S)
Flanged Bearing
2.5x
6x2.5mm
(HC400-S)
Tail Pin
(H0264-S)
Flanged Bearing
2.5x
6x2.5mm
(HC400-S)
Bell Crank Lever Assembly
Tail Side
Alluminum Case
(H0523-S)
Cross Tail Case
(H0526-S)
Tail Side Plate
Assembly
Bell Crank Lever
Assembly
Flanged Bearing
5x
13x4mm
(HC412-S)
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
20T Tail Pulley
(H0504-S)
Belt 1140-HTD-2
(HC455-S)
Vertical Fin
(H0532-S)
Tail System Assembly
Page 21
Chapter 13, Tail Assembly
Locking Element Tail Assembly .... x 2
Locking Element Tail
(H0535-S)
Locking Element
Tail Assembly
(H0535-S)
Double
Sided Tape
(HA033-S)
Bag 12, Box 3
Metric Hex
Nylon Nut M2.5
(HC200-S)
Double
Sided Tape
(HA033-S)
Red Tail Boom
(H0547-S)
Tail Boom Assembly
M8 Carbon Block Assembly
M8 Carbon Block
(H0534-S)
Metrix Nylon
Nut M8
(HC224-S)
M8 Carbon Block
Assembly
Double Sided Tape
(HA034-S)
Red Tail Boom
(H0547-S)
Yellow Tail Boom
(H0546-S)
Note:
We suggest to clean the sticking surface with sand paper.
Page 22
Chapter 13, Tail Assembly
Approx 474mm
5mm 5mm
13mm 13mm
A
DETAIL A
Carbon Road
Assembly
Plastic
Ball Link
(H0066-S)
Threaded Rod
M2.5x40mm
(HC242-S)
Plastic
Ball Link
(H0066-S)
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Finishing
Washer M2.5
(H0255-S)
Finishing
Washer M2.5
(H0255-S)
Bag 13
Socket Head Cap
Screw M2.5x10mm
(HC022-S)
Tail System
Assembly
Note: Please allow plenty of time for the glue to cure before inserting plastic ball link onto the threaded rod.
Threaded Rod
M2.5x40mm
(HC242-S)
Carbon Road
4x
2.5x420mm
(HC461-S)
Page 23
Chapter 13, Tail Assembly
Nylon Screw
M8x14mm
(HC164-S)
* Insert the boom. This operation is easier fitting into the main frame at a slight angle [Fig.1].
To facilitate boom insertion, you can also unscrew the two bolts that hold the tail servo support tray.
* Tighten the M8 nut with HA016 special tool supplied.
* After installation, connect the tail push rod.
* To lock the nut and prevent it from coming loose, install:
- H0287 (for FBL unit installed on the main plate) [Fig.2].
- H0564 (for FBL unit installed on H0564 ) [Fig.3].
[HC164]
Bag 14
NOTE:
[H0287]
[HC164]
[H0564]
BOOM ASSEMBLY
[HA016]
Page 24
Chapter 14, Installation Of The Boom, Canopy
CANOPY
Fit the canopy to the main frame until it stops. [Fig. 2]
Fit the canopy holes to the M4 set screws on the model.
Check alignment of the edge on the boom [Fig. 3]
If the alignment is correct, enlarge the 2 canopy holes with a reamer up to 10 mm in diameter.
If alignment is not OK, enlarge the 2 canopy holes in the appropriate direction up to 10 mm in diameter.
Install the canopy grommets. [Fig. 4]
The canopy can be locked using the knobs H0543. [Fig. 5]
NOTE:
If you want to use the rubber edge protector, you must increase the size of the opening
in the canopy that goes around the anti-rotation guide by approximately 2 mm per side.
TAIL BELT TENSION
*Check for the proper assembly of the tail boom.
*Loosen the tail case by loosening the 4 M2.5 screws.
*Install the belt onto the front pulley in the correct direction of rotation (figure 1).
*Rotate the tail drive several times by hand.
*Pull the tail case back to increase belt tension.
*Tighten the 4 M2.5 screws on the tail case.
*The belt must be very tight.
Bag 15
Page 25
Chapter 14, Installation Of The Boom, Canopy
Battery 6S
BATTERIES
The Goblin has a quick release battery tray system.
The batteries must be installed onto the battery tray to take advantage of the quick release locking system.
Install the battery to the battery tray using double sided tape and the long Velcro straps included (Fig 1 and Fig 2).
Make sure to find the right position of the battery to optimize the center of gravity.
The battery wires arranged as in fig 2 are particularly effective.
To insert the battery, simply align the battery tray in the slots at the front of the helicopter and slide all the way. The battery
will lock in place.
To remove the battery, simply lift up on the locking lever (Fig 5) and pull.
IMPORTANT:
Make sure the battery is locked in place before flight; the battery tray must be inside the slots on both sides!
Bag 16
Double Sided
Tape
(HA035-S)
Battery Tray
Support
(H0536-S)
Battery Strap
(HA036-S)
Page 26
Chapter 15, Battery
IN FLIGHT
3 blade rotor heads require a much lower cyclic gain on flybarless systems.We recommend that you set your gain at least
30% lower than the gain you normally use on your 2 blade rotor head helicopters.You can start increasing the gain after
you complete your first flight. Running too high of a gain can induce a violent oscillation that can potentially cause damage
to your helicopter in flight.
If the model is making strange noises, this can be usually attributed to incorrect belt tensions. Check the belts again and
tighten if necessary.
It's very important to check the model thoroughly after the first 2-3 flights. Check all bolts, screws, belts, ball links, etc.
SERIAL NUMBER
In Bag 19, you will find the serial number tag for your Helicopter.
Apply the tag as shown. Please remember to register your product. (See page 1)
Always in Bag 19, you can find also the KSE plate.
Main Blade
[HC200-S]
[HC026-S]
[HC206-S]
[HC079-S]
Bag 17
Tail Blade
OPERATIONS BEFORE FLIGHT
*Set up the transmitter and the flybarless system with utmost care.
*It is advisable to test the correct settings of the transmitter and flybarless system without main blades and tail blades fitted.
*Check that all wiring is isolated from the carbon/aluminum parts. It is good practice to protect them at the points where they
are at most risk.
*Be sure of the gear ratio, verifying carefully the motor pulley in use. The forces acting on the mechanics increase enormously
at higher RPM. Although the Goblin can fly at very high RPMs, for safety reasons we suggest to not exceed 3400 RPM.
*Fit the main blades and tail blades. (Fig.1 and Fig.2)
*Please make sure the main blades are tight on the blade grips, you should be able to violently jerk the head in both
directions and the blades should not fold. Failure to tighten the blades properly can result in a boom strike during spool up.
To fold the blades for storage, it is advisable to loosen them.
*Check the collective and cyclic pitch. For 3D flight, set about +/- 12.5°.
*It is important to check the correct tracking of the main blades. (Fig 3).
*Perform the first flight at a low head speed, 2400/2500 RPM.
After this first flight, do a general check of the helicopter. Verify that all screws and bolts are correctly tightened.
Page 27
Chapter 16, In Flight
MAINTENANCE
*On the Goblin 380, some areas to look for wear include:
- Motor belt
- Tail belt
- Dampers
*The most stressed bearings are definitely those on the tail
shaft and the thrust bearings.
Check them frequently. All other parts are not particularly subject to wear.
*The lifespan of these components varies according to the type of flying. On average it is recommended to check these parts every
20
flights. In some instances, based on wear, these parts should be replaced every
100
flights.
*Periodically lubricate the tail slider movement and its linkages as well as the swash plate movement and its linkages.
*To ensure safety you should do a general inspection of the helicopter after each flight. You should check:
- Proper belt tension (motor belt and tail belt).
- Proper isolation of the wires from the carbon and aluminum parts.
- All screws and bolts remain tight.
Page 28
Chapter 17, Maintenance
Main Frame
1
2
3
4
4
5
6
10
11
11
11
8
13
14
11
11
7
12
9
12
POS
COD
Name
Specification
Quantity
1
H0255
Finishing Washers M2.5
Aluminum
2
2
H0529
Plastic Battery Support
Plastic
1
3
H0530
Tail Servo Support
Plastic
1
4
H0531
Main Frame Carbon Fiber
2
5
H0536
Battery Tray Support
Carbon Fiber
1
6
H0539
Battery Aluminum Block
Aluminum
1
7
H0556
Landing Gear Support
Plastic
1
8
H0644
Landing Gear Support
Aluminum
1
9
H0645
CF Landing Gear
Carbon Fiber
2
10
HC005
Button Head Cap Screws
M2x5mm
1
11
HC019
Button Head Cap Screws
M2.5x6mm
14
12
HC022
Socket Head Cap Screws
M2.5x10mm
4
13
HA035 Double Sided Tape
1
14
HA036
Battery Strap
1
Page 29
Chapter 18, Exploded view, Carbon Frame
5
8
10
10
10
11
14
14
14
14
16
16
23
23
26
TRANMISSION ASSEMBLY TRANMISSION ASSEMBLY
14
2
3
4
6
7
9
12
13
15
17
17
18
19
20
21
26
22
22
24
25
1
1
1
POS
COD
Name
Specification
Quantity
14
HC020
Socket Head Cap Screws
M2.5x8mm
8
15
HC031
Head Cap Screws Shouldered
M2.5x15mm
1
16
HC032
Socket Head Cap Screws
M2.5x18mm
3
17
HC132
Flat Head Cap Screws
M3x5mm
4
18
HC144
Cone Point Set Screws
M3x6mm
1
19
HC153
Cone Point Set Screws
M4x12mm
1
20
HC184
Washers
4.3x
11x1mm
1
21
HC212
Metrix Nylon Nut
M4
1
22
HC418
Flanged Bearing
8x
12x3.5mm
1
23
HC419
Bearing
8x
16x5mm
2
24
HC440
One Way Bearing
8x
12x12mm
2
25
HC454
Motor Belt
304-2GT-09
1
26
HC462
Shim Washers
8x
12x0.2mm
2
POS
COD
Name
Specification
Quantity
1
H0255
Fnishing Washer M2.5
Aluminum
3
2
H0501
21T Motor Pulley ASM
Aluminum
1
3
H0502
120T Main Pulley
Aluminum
1
4
H0503
Fonrt Tail Pulley ASM
Aluminum
1
5
H0507
Main Shaft
Steel
1
6
H0519
Main Plate
Aluminum
1
7
H0520
Motor Support
Aluminum
1
8
H0522
Main Shaft Support
Steel
1
9
H0533
CF Anti-Rotation Guide
Carbon Fiber
1
10
H0548
Plastic Servo Support
Plastic
3
11
H0564
Flybarless Support
Aluminum
1
12
HC008
Socket Head Cap Screws
M2x8mm
3
13
HC018
Socket Head Cap Screws
M2.5x6mm
2
Page 30
Chapter 18, Exploded view, Transmission Assembly
5
6
6
6
HEAD SYSTEM HEAD SYSTEM
1
2
3
4
7
9
8
10
11
12
13
13
14
16
17
18
19
19
20
20
15
21
21
22
23
POS
COD
Name
Specification
Quantity
1
H0349
Washer
7,5x
10x0,5
2
2
H0403
Plastic Linkage Ball
M2
3
3
H0513
Main Blade Grip
Aluminum
3
4
H0524
Linkage Servos
Plastic
3
5
H0537
Uniball M2 Female
Aluminum
1
6
H0538
Uniball M2 Male
Steel
8
7
H0561
Linkage
M2x22mm
3
8
H0595
Main HUB
Aluminum
1
9
H0596
Main Spindle
Steel
3
10
H0597
Main Blade Grip Arm
Aluminum
3
11
H0598
Blade Grip Linkage
Aluminum
3
12
H0599
Bushing
Brass
3
POS
COD
Name
Specification
Quantity
13
H0600
Swashplate 01
Aluminum
1
14
HC020
Head Cap Screws
M2.5 x 8mm
2
15
HC028
Head Cap Screws
M2.5 x 15mm
3
16
HC074
Head Cap Shoulder
M3 x 16mm
1
17
HC079
Head Cap Shoulder
M3 x 18mm
3
18
HC096
Button Cap Screws
M4 x 6mm
3
19
HC206
Metric Hex Nylon Nuts
M3
4
20
HC400
Flanged Bearing
2x
6x2.5
6
21
HC411
B
earing
5x
10x4
6
22
HC435
Thrust Bearing
5x
10x4
3
23
HC449
C Washer
3
DS-3001HV
BK Servo
3
Page 31
Chapter 18, Exploded view, Head System
2
3
4
5
6
7
8
9
9
12
15
17
18
24
27
28
30
32
44
42
35
36
36
38
38
20
34
TAIL SYSTEM
TAIL SYSTEM
1
2
10
11
13
14
16
19
21
22
23
26
25
27
28
29
31
33
35
37
37
39
33
41
40
43
43
POS
COD
Name
Specification
Quantity
1
H0065
Uniball
M3 ø5 H6
2
2
H0066
Plastic Ball Link
M2,5
2
3
H0076
Grip Link Bushing
Brass
2
4
H0231
Tail Pitch Slider 01
Aluminum
1
5
H0232
Tail Pitch Slider 02
Aluminum
1
6
H0234
Bell Crank Lever
Plastic
1
7
H0253
Spacer Arm
ø2.5ø4x6.3
1
8
H0261
Tail Pitch Slider Link
Plastic
2
9
H0264
Tail Pin
Steel
2
10
H0279
Uniball
M3 ø5 H11.5
1
11
H0504
20T Tail Pulley
Aluminum
1
12
H0509
Tail Shaft
Steel
1
13
H0510
Tail Spindle
Steel
1
14
H0511
Tail Blade Grip
Aluminum
2
15
H0512
Tail Slider
Aluminum
1
16
H0515
Tail Hub
Steel
1
17
H0523
Tail Side Plate
Aluminum
1
18
H0526
Cros Tail Case
Aluminum
1
19
H0532
Vertical Fin
Carbon Fiber
1
20
H0534
CF Nut M8 Block
Carbon Fiber
1
21
H0535
Locking Element Tail
Carbon Fiber
2
22
H0540
Washer
ø3ø4.75x0.5
2
23
H0541
Washer
ø4.5ø5.9x0.5
2
24
H0546
Red Tail Boom
Carbon Fiber
1
POS
COD
Name
Specification
Quantity
25
H0566
Washer
ø2ø4.5x0.5
2
26
H0567
Tail Damper
Derlin
2
27
HC004
Socket Head Cap Screws
M2 x 6mm
4
28
HC018
Socket Head Cap Screws
M2.5 x 6mm
4
29
HC026
Socket Head Cap Screws
M2.5 x 12mm
2
30
HC032
Socket Head Cap Screws
M2.5 x 18mm
1
31
HC144
Cone Point Set Screws
M3 x 6mm
1
32
HC164
Nylon Screws
M8 x 14mm
1
33
HC200
Nylon Nut
M2.5
6
34
HC224
Nylon Nut
M8
1
35
HC242
Threaded Rod
M2.5x40mm
2
36
HC400
Bearing
ø2.5ø6x2.5
2
37
HC412
Flanged Bearing
ø5ø13x4
2
38
HC416
Flanged Bearing
ø7ø11x2.5
2
39
HC448
Thrust Bearing
ø3ø6x2.5
2
40
HC457
Bearing
ø3ø6x2.5
2
41
HC458
Bearing
ø3ø7x3
2
42
HC461
Carbon Rod
1
43
HA033
Double Sided Tape
2
44
HA034
Double Sided Tape
1
Page 32
Chapter 18, Exploded view, Tail System
- 5 x Uniballs M2
5H6.
- 5 x Uniball Spacers.
- 5 x Socket Head Cap Screws
M2x8mm.
- 5 x Socket Head Cap Screws
M2x6mm.
Uniball M2
5H6
[H0064-S]
- 5 x Uniballs M3x4
5H3.5.
Uniball M3x4
5H3
[H0065-S]
- 10 x Plastic Ball Link.
Plastic Ball Link
[H0066-S]
Bell Crank Lever
[H0234-S]
- 1 x Bell Crank level.
- 2 x Tail Pin.
- 2 x Flanged Bearing
2.5x
6x2.5mm.
- 1 x Spacer Arm
2.5x
4x6.3.
- 1 x Head Cap Screws M2.5x18.
- 1 x Uniball M3x
4 H5.
Finishing Washer M2.5
[H0255-S]
- 10 x Finishing Washer M2.5.
Tail Pitch Slider Link
[H0261-S]
- 2 x Tail Pitch Slider Link.
- 2 x Spacer
2x
3x3mm
.
- 2 x Socket Head Cap M2x6mm.
Plastic Ball Link M2
[H0403-S]
- 5 x Plastic Ball Link M2.
19T Motor Pulley
[H0501-19-S]
- 1 x 19T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
- 1 x 20T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
20T Motor Pulley
[H0501-20-S]
21T Motor Pulley
[H0501-21-S]
22T Motor Pulley
[H0501-22-S]
23T Motor Pulley
[H0501-23-S]
24T Motor Pulley
[H0501-24-S]
- 1 x 21T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
- 1 x 22T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
- 1 x 23T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
- 1 x 24T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
- 1 x 120T Main Pulley .
- 1 x Main Pulley Support.
- 2 x
Shims Ø8xØ14x0,2mm
.
- 5 x Head Cap Screws M2x5mm.
- 2 x Flanged Bearing Ø8xØ12x3,5mm.
- 1 x One Way Bearing Ø8xØ12x12mm.
Front Tail Pulley
[H0503-S]
20T Tail Pulley
[H0504-S]
- 1 x Front Tail Pulley Assembly.
- 1 x Head Cap Screws Shoulder
M2.5x15.
- 3 x Head Cap Screws M2x8mm.
- 1 x 20T Tail Pulley Assembly.
- 1 x Set Screws M3x6mm.
Main Shaft
[H0507-S]
- 1 x Main Shaft.
- 1 x Head Cap Screw M3x16mm.
- 1 x Metrix Nylon Nut M3.
25T Motor Pulley
[H0501-25-S]
- 1 x 25T Motor Pulley Assembly.
- 1 x Set Screws M3x6mm.
120T Main Pulley
[H0502-S]
- 1 x Tail Shaft.
- 1 x Tail Hub.
- 1 x Set Screw M3x6mm.
- 2 x Tail Damper.
Tail Shaft
[H0509-S]
Chapter 19, Spare Parts
Page 33
Tail Spindle
[H0510-S]
- 1 x Tail Spindle.
- 1 x Socket Cap Screw M2x6mm.
- 2 x Washer
2x
4.5x0.5mm.
Tail Blade Grip
[H0511-S]
- 2 x Tail Blade Grip.
- 2 x Thrust Bearing
3x
6x2.5mm.
- 2 x Bearing
3x
7x3mm.
- 2 x Bearing
3x
6x2.5mm.
- 2 x Washer
3x
4.75x0.5mm.
- 2 x Washer
4.5x
5.9x0.5mm.
- 2 x Washer
2x
4.5x0.5mm.
- 2 x Uniball M3.
Tail Pitch Slider
[H0512-S]
- 1 x Tail Pitch Slider 01.
- 1 x Tail Pitch Slider 02.
- 1 x Tail Pitch Slider 03.
- 2 x Flanged Bearings
8x
12x3.5mm.
Main Blade Grip
[H0513-S]
- 2 x Blade Grip.
- 2 x
Thrust Bearing
5x
10x4.
- 4 x
Bearing
5x
10x4.
- 2 x Washer
7.5x
10x0.5.
- 2 x Button Head Socket Cap M4x6.
- 2 x
Washer
5x
7x0.1.
Main Plate
[H0519-S]
- 1 x Main Plate.
- 1 x Bearing
8x
16x5.
Motor Support
[H0520-S]
- 1 x Motor Support.
- 3 x Head Cap Screws M2.5x8.
- 3 x Finishing Washer M2.5.
- 1 x Set Screws M4x12.
- 1 x Metrix Hex Nylon Nut M4.
- 1 x Washer
4x
11x1mm.
Main Shaft Support
[H0522-S]
- 1 x Main Shaft Support.
- 3 x Head Cap Screws M2.5x8.
- 1 x Bearing
8x
16x5.
Aluminum Tail Plate
[H0523-S]
- 1 x Aluminum Tail Plate.
- 1 x Flanged Bearing
5x
13x4.
- 2 x Head Cap Screws M2.5x10.
- 2 x Finishing Washer M3.
Linkage Servo
[H0524-S]
- 3 x Aluminum Tail Plate.
Cros Tail Case
[H0526-S]
- 1 x Cros Tail Case.
- 2 x Head Cap Screw M2.5x6.
Plastic Battery Support
[H0529-S]
- 1 x Plastic Battery Support.
Tail Servo Support
[H0530-S]
- 1 x Tail Servo Support.
- 4 x Buttom Head Cap
Specail M2.5x6.
- 2 x Uniball M2 Female.
Uniball M2 Female
(H0537-S)
Battery Tray
(H0536-S)
- 1 x M8 Carbon Block.
- 2 x Locking Element Tail.
- 1 x Double Sided Tape [HA034].
- 1 x Double Sided Tape [HA033].
- 1 x Metrix Hex Nylon Nut M8.
- 1 x Metrix Hex Nylon Screw M8.
- 4 x Metrix Hex Nylon Nut M2.5.
Boom Accessories
(H0535-S)
- 1 x Anti-Rotation Guide.
- 2 x Head Cap Screws M2.5x6.
Anti-Rotation Guide
(H0533-S)
Vertical Fin
(H0532-S)
- 1 x Vertical Fin.
- 2 x Finishing Washer M3.
- 2 x Head Cap Screws M2.5x6.
- 2 x Head Cap Screws M2.5x10.
- 1 x Main Frame.
Main Frame
(H0531-S)
- 1 x Battery Tray.
- 1 x Battery Straps.
- 1 x Double Sided Tape [HA036].
Chapter 19, Spare Parts
Page 34
Uniball M2 Male
(H0538-S)
- 5 x Uniball M2 Male.
- 1 x Battery Block.
- 1 x Button Cap Screws M2x5.
Canopy Nut
(H0542-S)
- 2 x Canopy Nut.
- 2 x Set Screws M4x20mm.
Canopy Knob
(H0543-S)
- 2 x Canopy Knob.
Yellow/Blue Canopy
(H0544-S)
Red/Black Canopy
(H0545-S)
Yellow Boom
(H0546-S)
Red Boom
(H0547-S)
- 1 x Yellow/Blue Canopy.
- 1 x Canopy Edge Protection.
- 2 x Canopy Grommet.
- 1 x Red/Black Canopy.
- 1 x Canopy Edge Protection.
- 2 x Canopy Grommet.
- 1 x Yellow Tail Boom.
- 1 x M8 Carbon Block.
- 2 x Locking Element Tail.
- 1 x Double Sided Tape [HA034].
- 1 x Double Sided Tape [HA033].
- 1 x Metrix Hex Nylon Nut M8.
- 1 x Metrix Hex Nylon Screw M8.
- 4
x Metrix Hex Nylon Nut M2.5.
- 1 x Red Tail Boom.
- 1 x M8 Carbon Block.
- 2 x Locking Element Tail.
- 1 x Double Sided Tape [HA034].
- 1 x Double Sided Tape [HA033].
- 1 x Metrix Hex Nylon Nut M8.
- 1 x Metrix Hex Nylon Screw M8.
- 4
x Metrix Hex Nylon Nut M2.5.
Battery Block
(H0539-S)
Tail Spacer KIT
(H0540-S)
- 2 x Washer
3x
4.75x0.5.
- 2 x Washer
4.5x
5.9x0.5.
- 2 x Washer
2x
4.5x0.5.
- 2 x Oring ID=2.9, S=1.78.
- 2 x Head Cap Screw M2x6mm.
Main Linkage Rod
(H0561-S)
- 2 x Steel Main Linkage Rod.
- 4 x Plastic Ball Link M2.
Plastic Servo Support
(H0548-S)
- 1 x Plastic Servo Support.
- 1 x Head Cap M2.5x18mm.
FBL Support
(H0564-S)
- 1 x FBL Support.
- 2 x Head Cap M2.5x8mm.
- 2 x Tail Fin Stickers.
- 2 x Landing Gear Stickers.
Tail Fin and Landing Gear Stickers
(H0565-S)
Tail Servo Spacer
(H0572-S)
- 4 x Tail Servo Spacer.
- 1 x Center Hub.
- 1 x Socket Head Cap Screw
Shouldered M3x16mm.
- 1 x Metric Hex Nylon Nut M3.
Center Hub
[H0595-S]
Yellow/Black Canopy
(H0559-S)
- 1 x Yellow/Black Canopy.
- 1 x Canopy Edge Protection.
- 2 x Canopy Grommet.
Page 35
Chapter 19, Spare Parts
[HC002-S] [HC004-S] [HC005-S] [HC008-S] [HC010-S]
[HC018-S] [HC019-S] [HC020-S] [HC022-S]
[HC031-S] [HC074-S]
[HC170-S] [HC184-S]
[HC144-S]
[HC155-S]
- 5 x Socket Head Cap
M2x5mm.
- 5 x Socket Head Cap
M2x6mm.
- 5 x Button Head Cap
M2x5mm.
- 5 x Socket Head Cap
M2x8mm.
- 5 x Socket Head Cap
M2x10mm.
- 5 x Socket Head Cap
M2.5x6mm.
- 5 x Button Head Cap
Special M2.5x6mm.
- 5 x Socket Head Cap
M2.5x8mm.
- 5 x Socket Head Cap
M2.5x10mm.
- 5 x Socket Head Cap
Shoulder M2.5x15mm.
- 2 x Socket Head Cap
Shoulder M3x16mm.
- 2 x Metrix Nylon Nut M3.
- 5 x Cone Point Set Screw
M3x6mm.
- 5 x Cone Point Set Screw
M4x20mm.
- 4 x Nylon Hex Nut
M8x14mm.
- 10 x Washer
Ø2,2xØ5x0,3mm.
- 5 x Washer
Ø4,3xØ11x1mm.
STANDARD SPARE PARTS
[HC026-S]
- 5 x Socket Head Cap
M2.5x12mm.
[HC032-S]
- 5 x Socket Head Cap
M2.5x18mm.
[HC096-S]
- 5 x Button Head Cap
Screws M4x6mm.
[HC156-S]
- 5 x Cone Point Set Screw
M4x12mm.
[HC164-S]
- 1 x Blade Grip Arm.
- 1 x Socket Head Cap
Screw M2.5.x8mm.
Blade Grip Arm
[H0597-S]
- 1 x Linkages.
- 1 x
Linkage Rod
.
- 1 x Bushing.
- 2 x Flanged Bearings
2.5x
6x2.5mm.
Linkage
[H0598-S]
- 1 x Swashplate Assembly.
- 5 x UniBall M2
4.7H3.
- 1 x UniBall M2
4.7H20.
Swashplate
[H0600-S]
- 1 x Spindle Shaft.
- 1 x C Washer
5x
5x0.2mm.
Spindle Shaft
[H0596-S]
- 1 x Plastic Landing Gear SET.
Plastic Landing Gear
(H0646-S)
CF Landing Gear
(H0645-S)
- 2 x CF Landing Gear .
- 4 x Specail Screws M2.5x6mm.
Page 36
Chapter 19, Spare Parts
[HC418-S] [HC419-S] [HC435-S] [HC440-S] [HC448-S]
[HC450-S] [HC453-S] [HC454-S] [HC455-S] [HC456-S]
[HC457-S] [HC458-S]
[HA021-S]
[HA039-S]
[HA035-S]
[HC459-S] [HC460-S]
[HA016-S]
- 2 x Flanged Bearing
Ø8xØ12x3.5mm.
- 2 x Bearing
Ø8xØ16x5mm.
- 2 x Thrust Bearing
Ø5xØ10x4mm.
- 5 x Washer
Ø5xØ7x0.1mm.
- 2 x Oring DI=6,75, S=1,78.
- 2 x Oring DI=2.9, S=1,78.
- 1 x Belt 304-2GT-09.
- 1 x Belt 1140-HTD-2.
- 4 x Bearing Ø3Ø6x2.5mm.
- 4 x Canopy Grommet.
- 1 x Foam Blade Holder.
[HC228-S]
[HC242-S] [HC400-S] [HC411-S] [HC412-S] [HC416-S]
- 4 x Shim
Ø8xØ14x0,2mm.
- 3 x Thread Rod
M2,5x40mm.
- 4 x Flanged Bearing
Ø2.5xØ6x2.6mm.
- 4 x Bearing
Ø5xØ10x4mm.
- 4 x Flanged Bearing
Ø5xØ13x4mm.
- 2 x Flanged Bearing
Ø7xØ11x2.5mm.
- 1 x One Way Bearing
Ø8xØ12x12mm.
- 2 x Thrust Bearing
Ø3xØ6x2.5mm.
- 4 x Flanged Bearing
Ø2xØ5x2.5mm.
- 4 x Bearing Ø3Ø7x3mm.
- 1 x Rad Bearing
Ø25Ø32x4mm.
- 1 x Spherical Bearing
Ø12xØ22x7mm.
[HC200-S]
- 10 x Metrix Nylon
Nut M2.5.
[HC206-S]
[HC224-S]
- 10 x Metrix Nylon
Nut M3.
- 4 x Metrix Nylon
Nut M8.
[HC212-S]
- 10 x Metrix Nylon
Nut M4.
[HC461-S]
- 1 x Tail Push Rod
Ø4xØ2,5x420mm.
- 2 x Plastic Ball Link.
- 2 x Thread Rod M2,5.
[HC462-S]
- 4 x Shim Ø8xØ12x0.1mm.
- 2 x Wrench Tool M8,M6.
[HA036-S]
- 1 x Tail Servo Horn.
- 3 x Cyclic Servo Horn.
- 2 x Battery Straps.
- 3 x Main Blade 360.- 2 x Tail Blade 70mm.
- 1 x Canopy Edge
Protection (1m).
[HA052-S]
[3BL360-3DW]
[BW0370-S]
[HA112-S]
- 2 x Double-sided Tape
1 mm Battery .
Page 37
Chapter 19, Spare Parts
Loading...