GOALRILLA B3333W, B3300W Owner's Manual

MODEL NO.

B33 33 W

CV54

BASKETBALL SYSTEM

O W N E R ' S M A N U A L

1. Read this manual carefully before starting assembly. Read each step completely before beginning

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.

3. Tomake assembly of your basketball system easier, use the Hardware Identifier on page 3
and 4 to identify and sort all fasteners. Check all cartons for kits. All hardware is not
located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting

holes may not align and parts may not easily fit together. Leave locknuts slightly loose until you are
instructed to tighten them.

An electric screwdriver is helpful in assembly. However, please set at low torque and use caution

5.

because you could overtighten the hardware and strip the screws.

Save this instruction and your proof of purchase (receipt) in the event that the manufacturer

6.

has to be contacted for replacement parts.

Please Do Not Return This Product To The Store!

Contact Escalade Sports customer service department at:
Phone: 1-888-USA-GOAL Toll Free !
Fax: [phone] Toll Free !
E-mail: [e-mail]
Mailing Address:
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at: www.G oalrilla.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION

®

2L-7248-03

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6419596, 6179733, 5919102, 5071120, 4798381, 4424968, D326128
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2018 Escalade Sports

2

HARDWARE IDENTIFIER

19

/12”

-13 x 1”
Hex Bolt

(2 Pieces)

41

Pull Pin

(1 Piece)

3

/12”

Flat Washer

(2 Pieces)

Lock Washer

5

1/2”X 1-1/4” Dia. Plastic-Washer

(4 Pieces)

18

51

1/2” Split

(2 Pieces)

Hardware located in 4A-7081-00 box

4

1/2”-13

Nylon Locknut (Thin)

(10 Pieces)

77

1/2”-13 x 9”

1/2”-13 x 9”

Hex Bolt

Hex Bolt

(1 Piece)

(1 Piece)

37

14mm ID X 28mm OD Dia. - Washer

(8 Pieces)

14

34

5/8” Thread

Protector

(4 Pieces)

5/8” Flat Washer (Thick)

(8 Pieces)

Hardware located in Anchor kit box

3

14

3/4” OD x 5-11/16

Pivot Tube (1 Piece)

HARDWARE IDENTIFIER

24

Hardware required for rim assembly

24

3/8” X 19mm Flat Washer

(8 pieces)

88

1/2”-13 x 10”

1/2”-13 x 10”

Hex Bolt

Hex Bolt
(3 Piece)

(3 Piece)

3/8” X 19mm Flat Washer

(4 pieces)

1/2”-13 X 1 3/4

Hex Bolt

(2 Pieces)

50

1/2”-13 X 2 1/4

Hex Bolt

(4 Pieces)

25

3/8”-16 X 1-1/4”

Hex Bolt

(4 Pieces)

12

#10 X 1 3/4” Phillips

Hex Head Self

Tapping Screw

(6 pieces)

5

1/2”X 1-1/4” Dia. Plastic-Washer

(18 Pieces)

Board Bushing

(2 pieces)

4

3

/12”

Flat Washer

(12 Pieces)

Two way Step Bushing

(2 pieces)

INSTALLATION TIMELINE

1. Prior to anchor system and goal assembly, call utility services for location of underground utility lines before you dig.

2. Vertical main post assembly is a two part process.

PART 1

Day 1. Complete Anchor System Installation Instructions.

(Below)

Day 2-4. Allow concrete to cure.

ANCHOR SYSTEM INSTALLATION INSTRUCTIONS (Day 1)

Before digging hole for anchor system, check for
buried power, gas, water, and telecommunication
lines! Failure to do so could result in serious or fatal
injury! Contact your local utility company if unsure.

Items needed for Anchor Installation (not included)

11 - 80 lb. bags of concrete (2-3 extra recommended)
1 - post hole digger (optional)
1 - 15/16” open end wrench
1 - 15/16” socket and ratchet (optional)
1 - concrete form (see note after step 2)

Note: For best results with less vibration, anchor system
should be independent of court. If pouring concrete for
both at same time, add an expansion joint in between.

Note: When digging hole, if you hit rock
and cannot dig through contact a contractor.

1. Determine the location of the anchor

system. The proper location is as close to
the court without making contact, as
shown in Figure 1. This,
however, is a general rule.
If you need to locate the
anchor system in a location other than
this, use the following dimensions as a
guide.

Overhang when adjusted to 10 ft. = 31 1/2”

2. Assemble anchor system as follows: Thread nut (#35) to bottom

of threads on anchor bolt (#39) insert threads of anchor bolt
(#39) through hole on anchor plate (#38) and secure with nut
(#35). Repeat this step for the remaining
anchor bolts. See
Figure 2. Note:

THESE NUTS

USED FOR

LEVELING

Each leg of
anch o r bolt s
should face the
anchor bolt to the
right. See Detail
A.

Figure 2

1 - wheel barrow
1 - garden hose
1 - level
1 - tape measure

MINI MUM

CLEA RANC E

REQU IRED

OVER HANG

18 INC H

REAR

PART 2

Day 5. Complete Goalrilla

TM

assembly instructions. (Requires

four adults)

Figure 1

Rebar

(Key #40)

Note: Using a concrete form for the top 4" of the concrete
is recommended. Cardboard forms can be purchased at
some hardware and home stores or a wooden form can
be constructed out of 2 x 4's.

Note: Failure to dig and fill hole as instructed will result
in increased system vibration.

*Tip: It is always a good idea to purchase one or two

extra bags of concrete, just in case you need them. If
extra bags are not used you can return them to the store.

3. Mix and pour concrete into hole. Follow instructions on

concrete bag. Stop about 18" below court level.

4. Insert four reinforcement bars (Key #40) into concrete 8"

apart creating a square in center on hole.

5. Place form in desired location and finish pouring concrete

up to court level.

6. Push anchor system into concrete and agitate to work out

voids in concrete. Immediately use a level to level and square
anchor plate to playing surface. Clean off any concrete that
may be on exposed threads.

Note: The bottom four nuts will be forever embedded in
concrete. The top four nuts remain on bolts and are
used for leveling. (See Step 11 on page 9)

Let concrete cure for a MINIMUM of 72 hours.

5

GOALRILLATMASSEMBLY INSTRUCTIONS (Day 5)

TOOLS REQUIRED FOR THE FOLLOWING STEPS

1 - 15/16" open end wrench
1 - 15/16” socket and ratchet (optional)
1 - 9/16” Deep Well Socket & Ratchet
1 - 3/4” Socket & Ratchet
1 - 3/4” Open end Wrench
1 - 5-16” Socket Driver

1 - Cordless Drill & 9/64” Drill Bit

1. Attach Post Brackets (#48) to outside of brackets on back

of Post Assembly (#2). Secure with two Hex Head Bolts (#25),

four Flat Head Washers (#26) and two Locknuts (#24) in

each Bracket (#48). See Figure 3.

2.

If not already pre-assembled, slide Plastic Actuator Sleeve
(#15) over Steel Actuator (#16) and place Actuator Cap (#13)
on top. Align holes in all 3 parts and slide Pivot Tube
(#14) through holes in Actuator Cap (#13) Plastic Actuator
Sleeve (#15) and Steel Actuator (#16) until equal amounts
stick out through both sides of actuator. See Figure 4.

NOTE: It may be necessary to use a rubber mallet

to tap in Pivot Tube.

NOTE: It is important for the installer to understand the
necessity of the Plastic washers (#5) provided. These
washers adequately space painted parts at all pivot points.
Neglecting the use of these washers will result in rusted
parts.

3. Lay Pole (#2) on its side on two padded saw horses. Attach

Actuator (#16) to Pole (#2) using one bolt (#19), split

lockwasher (#18), washer (#3) and two plastic washers (#5)

to thread into each side of Actuator. See Figure 4. Tighten
bolts tight.

If Pole Cap (#46) is not already pre-installed insert it

4.

into the top of the Pole (#2). It may be necessary to
use a rubber mallet to tap cap in.

14

1 - Level
1 - Tape Measure
1 - Rubber Mallet
1 - Set of Padded Saw Horses

1 - Ladder
1 - Pair of Safety Glasses
1 - Phillips Screwdriver

25

26

48

26

24

26

Figure 3

Figure 3

Figure 3

15

48

18

2

2

26

25

19

5

18

3

5

3

19

46

13

2

Figure 4

6