GN ReSound as
Global Technical Operations
gto.gnresound.com
Lautrupbjerg 9 • DK-2750 Ballerup • Denmark
E-Mail: Service@gnresound.dk
Technical Manual
ReSound Pulse CRT PS60-R
&
ReSound Pulse CRT LT PSS60-R
Doc. No. 0127420 rev. B
Page 2 of 15
Table of contents
Features ..............................................................................................................................3
Part list............................................................................................................................. 4-6
Final device .........................................................................................................................7
How to separate the HI ........................................................................................................8
Microphone assembly..........................................................................................................9
Hybrid connections ............................................................................................................10
Coating instructions ........................................................................................................... 11
Colour markers replacement .............................................................................................12
Test equipment ............................................................................................................ 13-14
Charger spares ..................................................................................................................15
Doc. No. 0127420 rev. B
Page 3 of 15
Description
Key features
• WarpTM high resolution compression
• New StabilizerTM DFS system
• SuperTuneTM intelligent rechargeability
• Directionality
• Environmental Steering automatic compressor tuning
• Virtual WindShieldTM wind noise reduction
• Multi-band noise reduction
• Low-level expansion
• Low Battery Warning Indicator
• Onboard AnalyzerTM DataLogging
Fitting Requirements
• Aventa tting software (2.3 or higher)
• CS63 Flex Strip programming cable
• HI-PRO, NOAHlink or SpeeLink
Standard Conguration
• Size 312 battery
• SmartStart power-up timer
• Battery door with integrated On/Off switch
• XReceivers w/sound tubes and domes in different sizes
• 3 standard colours: Medium blonde, marble grey & anthracite
Functional Description
The ReSound Pulse CRT (Canal Receiver Technology) is a receiver-in-the-ear model in the existing ReSound Pulse family. All features are
identical to the sound tube based ReSound models, except from that the receiver is removed from inside the device housing behind the ear and
instead placed at the edge of the tube inside the ear canal.
As from s/n 0700645699 PULSE CRT is delivered with hybrid Coyote 3.1. PULSE LT will continue to have the Coyote 3.0
mounted. For further information please also check GTO Technical News Bulletin No. 2007-08-001 - available on GTOweb
Doc. No. 0127420 rev. B
Page 4 of 15
Part List
Item
Part No.
MICROPHONE,9603 15071600
SUSPENSION,MIC,FRONT 15070700
SUSPENSION,MIC,REAR 15070800
SPRING,BAT,POSITIVE,PLATED 15071101
SPRING,BAT,NEGATIVE,PLATED 15071001
CONTACT,PROGRAMMING MODULE 15070600
FLEX-HYBRID,C3.0,DENMARK 15157500
FLEX-HYBRID,C3.1 FOR PS60-R ONLY 16016900
PIN,LOCK Ø=0.6, L=7.1 15136900
RUBBER GLUE C-296336310 1901-061
GREASE MOLYKOTE FS1292 1908-209
COLOUR MARKER,RED 15075500
COLOUR MARKER,BLUE 15075501
COATING, EGC-1700, 100ML 15290401
WIRE,ESW,RED,7X32U,12MM 15129612
WIRE,ESW,RED,7X32U,8MM 15129608
WIRE,ESW,RED,7X32U,16MM 15129616
WIRE,ESW,GREEN,7X32U,9MM 15129809
WIRE,ESW,GREEN,7X32U,16MM 15129816
Item
Part No.
WIRE,ESW,GREEN,7X32U,11MM 15129811
WIRE,ESW,BLUE,7X32U,9MM 15129909
WIRE,ESW,AMBER,7X32U,9MM 15129709
WIRE,ESW,AMBER,7X32U,12MM 15129712
WIRE,ESW,GREEN,7X32U,12MM 15129812
CERUSTOP FILTER (KIT) 098-0282
PIN REMOVAL TOOL 15492900
CONNECTOR,CRT 004-0073
PROGRAMMING CABLE,RED 15206700
PROGRAMMING CABLE,BLUE 15206701
STRIP CS63/NWT/FLEXSTRIP(10Pk) 50931703
STRIP CS63/NWT/FLEXSTRIP(25PK) 50931704
KIT PROGRAMM. CABLE W/FLEX,RED 15254800
KIT PROGRAMM. CABLE W/FLEX,BLUE 15254801
SIMULATED BATT. PILL,SIZE 312 15854900
TEST FIXTURE 16229100
MEASUREMENT TOOL CRT 004-2013
XREC TEST TUBE 16185100
2CC SNAP-ON ADAPTOR DSA 5000 15238500
Doc. No. 0127420 rev. B
Page 5 of 15
Part list
FramePSS60-R
Part No.
FRAME,CRT,PTD,MDM BLONDE 16125102
FRAME,CRT,PTD,ANTHRACITE* 16125108
Filter, Front
Part No.
FILTER,MIC.FRONT.4PCS.MDM BL 15071202
FILTER,MIC,FRONT,4 PCS,MR GREY 15071204
FILTER,MIC,FRONT,4PCS,ANT 15071208
Filter, Rear
Part No.
FILTER,REAR,312,4PCS,MBL 15798902
FILTER,REAR,312,4PCS,MARBLE GR 15798904
FILTER,REAR,312,4PCS,ANT 15798908
Frame PS60-R
Part No.
FRAME,CRT,PTD,MDM BLONDE 16023402
FRAME,CRT,PTD,ANTHRACITE* 16023408
HI COMPLETE - PSS60-R
Part No.
MEDIUM BLONDE 16125202
MARBLE GREY 16125204
ANTHRACITE 16125208
HI COMPLETE - PS60-R Ver. 3.1
Part No.
MEDIUM BLONDE 16463302
MARBLE GREY 16463304
ANTHRACITE 16463308
*is used for both ANT and MGR HI
Housing KIT 312 - PS60-R &
PSS60-R
Part No.
BLACK 16079101
MEDIUM BLONDE 16079102
METALLIC 16079103
MARBLE GREY 16079104
BLACK METALLIC 16079105
MEDIUM BLONDE METALLIC 16079106
COOL GREY 16079107
ANTHRACITE 16079108
MONZA RED 16079109
PURPLE/GREEN 16079110
PURPLE/BLUE 16079111
GOLDEN/GREEN 16079112
BRONZE/BORDEAUX 16079113
WIMBLEDON GREEN 16079115
STEEL SILVER 16079116
LAVA BLACK 16079117
OCEAN BLUE 16079118
To replace a housing or battery door or to change to another
housing colour, a kit consisting of housing and battery door
must be ordered
Doc. No. 0127420 rev. B
Page 6 of 15
Part list
Item
Part No.
Ear Box 16069100
Containing:
AXLE 0.68X4.8MM 002-0386-1
PIN REMOVAL TOOL 002-0404
MEASUREMENT COUPL. ADAPTOR,CRT 002-0412
UNIVERSAL ADAPTABLE RETENTION 004-0011-001
MEASUREMENT TOOL CRT 004-2013
OPEN DOME,5L 054-0332
OPEN DOME,7L 054-0333
OPEN DOME,10L 054-0334
OPEN DOME,5S 054-0338
OPEN DOME,7S 054-0339
OPEN DOME,10S 054-0340
TULIP DOME,L 054-0390
TULIP DOME,S 054-0391
XRECEIVER STANDARD UNIT XS 0-L 16069200
XRECEIVER STANDARD UNIT XS 1-L 16069300
XRECEIVER STANDARD UNIT XS 2-L 16069400
XRECEIVER STANDARD UNIT XS 3-L 16077100
XRECEIVER STANDARD UNIT XS 0-R 16077200
XRECEIVER STANDARD UNIT XS 1-R 16077300
XRECEIVER STANDARD UNIT XS 2-R 16077400
XRECEIVER STANDARD UNIT XS 3-R 16077500
XREC STD UNIT - PACKED
XREC STD UNIT - UNPACKED
Doc. No. 0127420 rev. B
Page 7 of 15
Final Device
XREC to be plugged into the stud of the HI
Cerustop lter kit p/n 098-0282
Filter removal tool
Wax guard
Doc. No. 0127420 rev. B
Page 8 of 15
How to separate the HI
Remove the lter for back microphone
Gently press out the two pins by using
the pin removal tool and pull them out
by using e.g. tweezers. Take out the
battery door and pull out the frame. Filters are recommended to be replaced
during any repair situation
Pin removal tool p/n 15492900
Doc. No. 0127420 rev. B
Page 9 of 15
Microphone Assembly
Note: Make sure that the microphone is
turned right. The wires must be turned
towards the back mic suspension as
shown on the drawing.
Use service tool (heat zink) when soldering the microphone wires.
Brush EGC-1700 coating to the solder points and let dry for 15 sec
- then brush once more.
Wire, red 12 mm
p/n 15129612
Wire, green 12 mm
p/n 15129812
Wire, amber 12 mm
p/n 115129712
Make sure that the suspensions t well to the
sound studs/ports on the microphones.
Front mic suspension Back mic suspension
-
IN
+
Make sure that wire insulation is undamaged.
Doc. No. 0127420 rev. B
Page 10 of 15
Hybrid connections
Contact module
Battery springs
BAT(+)
H8
H9
/REC(+)
REC(-)
MIC+
MIC-
MIC IN
Contact
module
BAT(-)
Contact
module
Coyote 3.0 - No marking
Coyote 3.1 - Black dot marking
The layout of C3.0 and C3.1 is the same. For visual purpose the C3.1 is
marked with black dots. Only PS60-R is mounted with hybrid C3.1. In a
repair situation a hybrid C3.0 can be replaced to C3.1. The test system
will automatically detect the hybrid version during test.
NOTE:
Please also see Technical News Bulletin No. 2007-08-001 (available
from GTOweb) which is describing the implementation of C3.1.
Furthermore the improved test xture is described
Doc. No. 0127420 rev. B
Page 11 of 15
Coating
Cover the pins of the contact module at the solder points and at the in-mould. Press it under the
contact pins to ensure good protection.
Molykote
Add molykote in the area indicated by the red dotted lines.
Fill the holes at the battery solder points on both sides with Molykote FC1292 p/n
1908-209. Wipe the surplus Molykote off to prevent soiling of the housing at nal
assembly.
Doc. No. 0127420 rev. B
Page 12 of 15
Colour Markers
Turn the pin
around
Pressure here with a nger
How to place the colour marker:
Place the colour marker as long into the hole as
possible. Press on the back of the marker with a
nger and at the same time turn the pin around until it
breaks of.
How to remove the colour marker:
Push out the pin a 1/3 of its length using pin tool and turn the device
as if it was placed on the ear. The colour marker should then fall out.
If the colour marker is not falling out, the battery door can be opened
and from the inside the colour marker can be pushed out by using a
“colour marker remover” p/n 15426100.
The pin is pushed out
Push the colour marker
from inside
Colour marker,
Red p/n 15075500
Blue p/n 15075501
Red p/n 15175600, 25 pcs
Blue p/n 15175601, 25 pcs
Doc. No. 0127420 rev. B
Page 13 of 15
Test equipment
Kit with programming cable, ex strip and
clothes-clip:
- Red p/n 15254800
- Blue p/n 15254801
Programming cable CS63 blue,
Left p/n 15206701.
Programming cable CS63 red,
Right p/n 15206700.
Red dot
Blue dot
Battery pill must be used:
Size 312 p/n 15854900
- Flex strip 3 pin (10 pcs) p/n 50931703
- Flex strip 3 pin (25 pcs) p/n 50931704
Doc. No. 0127420 rev. B
Page 14 of 15
Place the Xrec tube into the test xture. Mount the snap
on adaptor on the coupler and place the XRec into it.
Connect the hearing instrument to the other end of the
Xrec tube
Test xture p/n 16229100
Test equipment
Use XRec test tube p/n 16185100 when
testing
The test xture must be adjusted before use. Loose the
two screws. The smallest part must be positioned so that
the test tube is in the center of the green circle. Fasten
the screws.
This adjustmest must also be done on a frequently basis
to ensure optimal testing.
Insert battery pill and ex strip into the HI
Snap-on adaptor p/n 15238500. To be used with Otometrics 2cc coupler.
Doc. No. 0127420 rev. B
Page 15 of 15
Charger spares
Spares Part no.
Keyring holder 15734700
Link for keyring holder 15806700
Silicone block 10A 15734300
Silicone block 312 15837300
Battery slide 10A 15837100
Battery slide 312 15837200
Power supply EU 15836800
Power supply UK 15837900
Power supply US 15837500
Power supply AUS 15837700
Complete package Part no.
RESOUND PULSE SUPERTUNE, EU*
15871100
RESOUND PULSE SUPERTUNE, UK*
15870900
RESOUND PULSE SUPERTUNE, US*
15871000
RESOUND PULSE SUPERTUNE, AUS*
15870100
* including all spares
Loading...