Thank you for purchasing a Jabra SP500, the most versatile Bluetooth speakerphone on
English
the market. Jabra has become the market leader in hands-free communication products
through the innovation and performance of our products. The Jabra SP500 is designed to
perform superbly in any location – in the car, the home or the office.
Drive safely
!
BEFORE USING YOUR SPEAKERPHONE
Check for phone compatibility
1
The Jabra SP500 is compatible with most Bluetooth¹ (see
check whether your phone has Bluetooth capability by visiting your phone manufacturer’s
web site or Jabra’s web site (http://www.Jabra.com/JabraCMS/NA/EN/MainMenu/Products/
ProductFinder.htm) which has complete information on compatibility.
Glossary
) mobile phones. You can
English
Several studies have shown that cell phone usage while driving creates a distraction to
the driver which may increase the likelihood of an accident. This distraction potential
is not eliminated by the use of a hands-free phone. Hands-free phones have not been
shown to be safer than hand-held phones with respect to driver distraction. When using
the phone while driving, keep conversations short and resist any temptation to make
notes or read documents. Before answering calls consider your circumstances. Pull off
the road and park before making or answering calls when driving conditions require
(e.g. bad weather, high traffic density, presence of children in the car, difficult junctions
or maneuvers.)
Remember, driving comes first, not the call!
Abide by local laws.
Please check if the local laws where you live restrict the use of mobile phones while
driving. It is the owner’s responsibility to use this product in compliance with the laws of
the place where you live.
Jabra SP500 Overview
1
Multi-function Button
2
Indicator Light (Blue/Yellow/Red)
3
Volume Control
4
Mute Button
5
Microphone Boom
6
Pairing Button
7
Charging Socket
8
Speaker
2
Charge the batteries
2
The Jabra SP500 comes complete with two 1.2-volt (AA 2000 mAh) rechargeable
batteries that must be fully charged before you use the speakerphone for the first time.
1. Important: Remove the battery protection plastic sheet to activate the batteries.
(See fig. 1. )
2. Plug the adapter jack into the speakerphone and the AC adapter or the vehicle
power charger into a power socket.
3. The red light will turn on when charging begins. After approximately two hours, the
red light will go out indicating that the Jabra SP500 is fully charged.
4. Unplug the AC adapter or the vehicle power charger lead from the speakerphone.
5. You are now ready to “pair” the Jabra SP500 with your mobile phone.
WARNING:
destroy the speakerphone. We recommend that you use the rechargeable batteries
supplied but you can use other brands.
in your Jabra SP500.
3
Switch on the Jabra SP500
1. Press and hold the multifunction button until you hear the start up melody and
the blue LED light flashes three times. When the speakerphone is in standby mode,
the blue LED light flashes every three seconds.
Please note that the blue light will automatically switch off after one minute in order to
save power and to not distract when driving at night. The light will be re-activated upon
any key press.
Switch off the Jabra SP500
1. Press and hold the multifunction button for approximately five seconds until you
hear the shut down melody and the LED light has been switched off completely.
1
(See fig. 1. )
Using another AC adapter other than the one provided may damage or
1
You cannot use non-rechargeable batteries
Switching on the Jabra SP500
(See section 4)
3
“Pair”² with your Bluetooth mobile phone
4
1. Ensure SP500 is switched on.
English
2. Press the pairing button until you see a
seconds),
then
release
3. Set your Bluetooth phone to “discover” the speakerphone by following your
phone’s instruction guide. Typically, the steps involve going to a “setup,” “connect,”
or “Bluetooth” menu
Bluetooth device*.
4. Your phone should find the “Jabra SP500” speakerphone and ask if you want to pair
with it. Confirm by pressing “yes” or “ok.”
5. Enter
passkey or PIN³ = 0000 (4 zeros)
IMPORTANT: If pairing was successful, the blue indicator light will briefly flash
rapidly before going back to flashing
confirmation melody. If unsuccessful, the blue light remains solid, and you’ll need to
re-attempt pairing.
(See steps 3–5 above)
(See section 3)
solid blue
. Your speakerphone is now in pairing mode.
on your phone
(See example from a typical mobile phone in fig. 3)
and then selecting the option to “discover” a
blue every three seconds. You will also hear the
light (approximately two
, then press “yes” or “ok.”
USING YOUR Jabra SP500
Before using your Jabra SP500, ensure that the batteries are charged and the Jabra SP500
is paired (see item 3) with your Bluetooth mobile phone and switched on.
The speakerphone can be used while being recharged from a wall socket or from the car
charger.
Making a call
5
Using your mobile phone’s keypad
1. Dial number on keypad.
2. Press phone’s “send” key.
3. The Jabra SP500 has automatic volume control and will automatically adjust the
speaker volume based on the relevant background noise. In order to adjust the
volume according to your own preferences, use the volume control wheel.
Using voice-dialing (if supported by your phone)
1. Press and release once. You’ll hear one short beep while doing this.
2. You’ll then hear the voice-activation tone; say the name of the person you wish to call.
NOTE: Record voice tag via your mobile phone. If you have a Nokia phone you will be
able to record the voice tags via your speakerphone.
4
Ending a call
6
•
Press and release once.
OR
•
End call from your mobile phone’s keypad.
Answering a call
7
•
After you hear the ring tone, press and release once.
OR
•
Answer the call with your mobile phone’s keypad. You may then need to transfer the call
to the speakerphone by pressing and releasing once (depending on your phone).
Muting a call
8
•
To enable mute press the mute button for one second and you will hear a short
beep. You’ll see a
•
To disable mute function press the
Call-waiting*
9
•
It is recommended that you use your mobile phone’s keypad which typically
involves pressing the “send” button.
OR
•
Press and hold until you hear two beeps to answer the incoming call and switch
between calls
* See
To avoid the Jabra SP500’s LED light from distracting you when driving at night, the LED
light will be switched off one minute after an active call. It is also possible to prevent the
LED light from flashing by pressing and holding the mute button for 10 seconds until you
hear a second beep. The Jabra SP500 will still function during this time. When you switch
off the unit and then switch it back on again the LED light will commence flashing again.
Enhanced features
mobile phones that support the hands-free profile. See section 13 for further
details about Bluetooth profiles.
Indicator light
10
solid
yellow
light.
mute button
(some phones do not support call-waiting via this method).
section for alternative call-waiting instructions for
briefly.
English
5
6
English
Office mode
11
Office mode creates the appropriate sound sensitivity to provide optimal performance
English
of the Jabra SP500 in the office or home environment. It's recommended that you only
use this mode in the above mentioned environments.
• By pressing and holding the mute button for five seconds you will see the blue LED
flash rapidly and hear a short beep.
• To return to normal mode, repeat the above action
When Jabra SP500 is in office standby mode, blue LED light flashes twice every
three seconds.
For optimal performance during teleconferences, please ensure all participants
face the microphone
Choosing speakerphone placement
12
For optimal performance, place your Jabra SP500 in direct line of sight with your Bluetooth
mobile phone. You will get better performance when there are no obstructions (including
parts of your body) between the Jabra SP500 and your mobile phone. Ensure that the
microphone is pointing towards your mouth for optimal sound clarity.
The Jabra SP500 comes with two mounting options for your vehicle.
• A clip for attaching to the sun visor
windscreen.
(See fig. 4)
(See fig. 3)
and suction mount for use on the
To release the clip or suction mount – just pull the clip or suction
mount outwards.
IMPORTANT: Ensure that the speakerphone does not obstruct your view of the road or
other road users. It is the owner’s responsibility to ensure that the Jabra SP500 does not
create a safety hazard and that its positioning complies with Federal and State laws.
The Jabra SP500 should also be positioned such that it does not interfere with
any vehicle safety equipment, including air bags. The Jabra SP500 should be positioned
securely. Please be aware that in the event of a crash, loose objects may contribute to
driver injury by becoming projectiles.
(See fig. 3.3 and 4.3)
Replacing the batteries
13
The Jabra SP500 comes complete with two 1.2-volt (AA) rechargeable batteries.
You may have to eventually replace the batteries. Please use standard rechargeable
1.2 volt (AA 2000 mAh) NiMh batteries.
1. Remove the back cover from the speakerphone and replace both batteries as
indicated. Re-attach the back cover to the speakerphone.
Enhanced features (for Bluetoot h mobile phones
14
with hands-free profile)
Bluetooth profiles⁴
each other. Bluetooth phones support different sets of profiles – most support both
headset and hands-free profiles. In order for Bluetooth devices to talk to each other they
need to support the same Bluetooth profile. Jabra SP500 supports both the headset and
hands-free profiles.
Although the Jabra SP500 is compatible with Bluetooth phones with either Bluetooth
profile, enhanced features are available only for phones that support the handsfree Bluetooth profile. Check your phone’s instruction guide or contact the phone
manufacturer to find out if your phone supports the hands-free Bluetooth profile.
Enhanced features:
• Last number redial
While the speakerphone is on, press and hold
release immediately.
• Rejecting an incoming call
When your phone rings, press and hold
immediately.
• Call-waiting
When your phone notifies you of another incoming call while you’re on a call, press
and hold
• Putting a call on hold
While you’re on a call, press and hold
immediately. Repeat to retrieve the call.
are protocols through which Bluetooth devices communicate with
(when not on a call)
until you hear 2 short beeps,
(when not on a call)
until you hear 2 short beeps, release
(swapping between two calls)
until you hear 2 short beeps, release immediately.
until you hear 2 short beeps, release
(See fig. 5)
English
7
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.