Integration Manual
SANGOMA-MSMA
13.56 Mhz Multi Standard - Multi Antenna Reader/Writer
Manual version 1.0
(C) 2016 by GMMC GmbH Page 1 of 9
2V3
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 2 of 9
Hardware &
Software
1. Short description
Power supply
USB : 5V (+0,25V -0,6V) via Mini USB Connector and cable
Note: it is recommended to use a clip on ferrite on the USB cable on module side.
Operating temperature: 0°C – 65°C
Storage temperature: 0°C-75°C
Supported 13,56MHz RF standards
ISO/IEC 14443 – ASK
ISO/IEC 15693 – ASK
modulation
modulation
USB host communication (via VCP Virtual COM port)
Antenna connection
via 3 pin gold plated header and connector
Note: Only antenna channel 1 is operational in this version. The other channels are blocked by firmware and /
or are not equipped with components / connectors.
Short functional description:
Once the reader device is connected and USB power is available the device boots up. The RF field remains
switched OFF. The reader firmware has Reader and RFID tag related commands implemented.
If a tag command is sent to the specified antenna port the RF Filed is switched on during tag processing and
will be automatically switched off after the tag response has been received.
The two on board status LEDs (red/green) are disabled after boot and need to be switched on using the DO
command as described at a later stage in this manual.Reader related commands do not switch on the RF field.
For the full command description refer to the SANGOMA-MSMA user manual.
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 3 of 9
2. Hardware
2.1 Physical dimensions
• Outer dimensions 52mm (2,05 inch) x 50 (2,97 inch)
• Mounting Holes (diameter 3mm/0,012inch) are connected to system ground.
Hardware &
Software
3. Module and antenna installation
´
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 4 of 9
Hardware &
Software
• Mount the Module properly into the end device
• Mounting holes are connected to system ground – its recommended to connect at least one
mounting whole the end-device system ground
• Connect the antenna to channel one of the module as shown in the above illustration – note
the connector is symmetrical and the direction 0° or 180° do not matter for functionality or
RF compliance..
• Attach power to the Module via USB cable to the end device application host – it is
recommended to apply a click on ferrite on the USB cable on the system side
4. Antenna specification:
The antenna to be used is SANGOMA-Jay 1v1 with 75cm twisted 3 wire cable and connector.
(GMMC part number : SANGOMA-ANTJAY602075)
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 5 of 9
Hardware &
Software
5. Compliance statements
FCC COMPLIANCE STATEMENT
NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Caution!
The Federal Communications Commission (FCC) warns the users that changes or modifications to the
unit not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC §15.105 (b):
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or telev
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
ision reception, which can be deter-mined by turning the
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help.
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 6 of 9
Hardware &
Software
RSS COMPLIANCE STATEMENT
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
6. Module label location
Module back side
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 7 of 9
Hardware &
Software
7. End device labeling instructions
FCC notes for all hosts devices. The end device must be labeled with:
Contains FCC ID: 2AKHW-SANGMSMA1
Contains IC: 22202-SANGMSMA1
Labelling Requirements
In addition following statement shall be placed on the device:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Where the product is so small or for such use that it is not practicable to place the statement on it,
the statement can be placed in a prominent location in the instruction manual.
Information to the user
- For Class A devices the manual of the host shall include the following statement:
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
- For Class B devices the manual of the host shall include the following statement:
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason-able
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or telev
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
--Reorient or relocate the receiving antenna.
ision reception, which can be deter-mined by turning the
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help.
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 8 of 9
Modification of equipment
The instruction manual of the host shall include the following statement: Changes or modifications
made to this equipment not expressly approved by the party responsible for compliance may void
the FCC authorization to operate this equipment.
Special accessories
Where special accessories such as shielded cables and/or special connectors are required to comply
with the emission limits, the instruction manual shall include appropriate instructions on the first
page of the text describing the installation of the device.
Final Compliance of end product
The integrator is responsible for the final compliance of the end product including this certified
transmitter module. CFR 47 §15.101 give guidance in terms of applicable equipment authorization
procedures of different end-products. Typically compliance to subpart 15 B (§15.107 and 15.109)
Class A or B including verification of the subpart 15 C compliance (field strength of fundamental and
out-of-band emissions) of the transmitter parameters apply.
Simultaneous transmission
When the host product supports simultaneous-transmission operations the host manufacturer needs
to check if there are additional RF exposure filing requirements due to the simultaneous
transmissions. When additional application filing for RF exposure compliance demonstration is not
required (e. g. if the SANGOMA-MSMA 2V3 module in combination with all simultaneously operating
transmitters complies with the RF exposure simultaneous transmission SAR test exclusion
requirements), the host manufacturer may do his own evaluation without any filing, using
engineering judgment and testing
for confirming compliance with out-of-band, restricted
reasonable
band, and
spurious emission requirements in the simultaneous-transmission operating modes.
If additional filing is required please contact the person at GMMC GmbH responsible for certification
of the SANGOMA-MSMA 2V3 module.
U s e r M a n u a l
NFC Wizard Reader MSMA / Writer – Multi Antenna
(C) 2016 by GMMC GmbH
Page 9 of 9
Version Remarks
V1.0 Initial released version
V1.1 Updates regarding temperature range and antenna (usage and installation)
8. Revision history
Hardware &
Software
Loading...