D6014 - SIL 3 Repeater Power Supply G.M. International ISM0210-2
SIL 3 Repeater Power Supply
Hart, DIN-Rail and Termination Board,
Models D6014S, D6014D
D6014S - D6014D
INSTRUCTION MANUAL
2
D6014 - SIL 3 Repeater Power Supply G.M. International ISM0210-2
General Description: The single and dual channel Repeater Power Supply, D6014S and D6014D module is a high integrity analog input interface suitable for applications
requiring SIL 3 level (according to IEC 61508:2010 Ed.2) in safety related systems for high risk industries. Provides a fully floating dc supply for energizing conventional
2 wires 4-20 mA, active or passive, transmitters and repeats the current in floating circuit to drive a load.
The circuit allows bi-directional communication signals, for Hart transmitters.
Mounting on standard DIN-Rail, with or without Power Bus, or on customized Termination Boards.
Functional Safety Management Certification:
G.M. International is certified by TÜV to conform to IEC61508:2010 part 1 clauses 5-6 for safety related systems up to and included SIL3.
Technical Data
Characteristics
Supply: 24 Vdc nom (18 to 30 Vdc) reverse polarity protected, ripple within voltage limits 5 Vpp, 2 A time lag fuse internally protected.
Current consumption @ 24 V: 90 mA for 2 channels D6014D, 45 mA for 1 channel D6014S with 20 mA output typical.
Power dissipation: 1.35 W for 2 channels D6014D, 0.675 W for 1 channel D6014S with 24 V supply voltage and 20 mA output typical.
Isolation (Test Voltage): In/Out 2.5 KV; In/Supply 2.5 KV; In/In 500 V; Out/Supply 500 V; Out/Out 500 V.
Input: 4 to 20 mA (separately powered input, voltage drop 0.5 V) or 4 to 20 mA (2 wires Tx current limited at 25 mA), reading range 0 to 24 mA.
Transmitter line voltage: 15.0 V typical at 20 mA with max. 20 mVrms ripple on 0.5 to 2.5 KHz frequency band, 14.5 V minimum.
Output: 4 to 20 mA, on max. 550 load in source mode (typical 12 V compliance);
V min. 8 V at 0 load V max. 30 V in sink mode, current limited at 25 mA or
1 to 5 V on internal 250 shunt (or 2 to 10 V on internal 500 shunt on request).
Response time: 5 ms (0 to 100 % step change).
Output ripple: 20 mVrms on 250 communication load on 0.5 to 2.5 KHz band.
Frequency response: 0.5 to 2.5 KHz bidirectional within 3 dB (Hart protocol).
Performance: Ref. Conditions 24 V supply, 250 load, 23 ± 1 °C ambient temperature.
Calibration accuracy: ± 0.1 % of full scale.
Linearity error: ± 0.05 % of full scale.
Supply voltage influence: ± 0.02 % of full scale for a min to max supply change.
Load influence: ± 0.02 % of full scale for a 0 to 100 % load resistance change.
Temperature influence: ± 0.01 % of full scale on zero and span for a 1 °C change.
Compatibility:
CE mark compliant, conforms to Directive: 2014/30/EU EMC, 2014/35/EU LVD, 2011/65/EU RoHS.
Environmental conditions:
Operating: temperature limits – 40 to + 70 °C, relative humidity 95 %, up to 55 °C.
Storage: temperature limits – 45 to + 80 °C.
Approvals:
TÜV Certificate No. C-IS-722134640-01, SIL 2 / SIL 3 conforms to IEC61508:2010 Ed.2.
TÜV Certificate No. C-IS-236198-09, SIL 3 Functional Safety Certificate conforms to IEC61508:2010 Ed.2, for Management of Functional Safety.
Mounting:
T35 DIN-Rail according to EN50022, with or without Power Bus or on customized Termination Board.
Weight: about 155 g D6014D, 130 g D6014S.
Connection: by polarized plug-in disconnect screw terminal blocks to accomodate terminations up to 2.5 mm
2
.
Protection class: IP 20.
Dimensions: Width 12.5 mm, Depth 123 mm, Height 120 mm.
FSM
SIL 3
3
D6014 - SIL 3 Repeater Power Supply G.M. International ISM0210-2
Ordering Information
Front Panel and Features
SIL 3 according to IEC 61508:2010 Ed.2 for Tproof = 1 / 10 yrs (10% / >10 % of total SIF).
SIL 2 according to IEC 61508:2010 Ed.2 for Tproof = 14 / 20 yrs (10% / >10 % of total SIF).
PFDavg (1 year) 6.69 E-05, SFF 90.47 %.
Systematic capability SIL 3
2 fully independent channels.
4-20 mA Input / Output Signal Active-Passive / Source-Sink
Hart compatible.
Input and Output short circuit proof.
High Accuracy.
Three port isolation, Input/Output/Supply.
EMC Compatibility to EN61000-6-2, EN61000-6-4, EN61326-1, EN61326-3-1 for safety system.
In-field programmability by DIP Switch.
TÜV Certification.
TÜV Functional Safety Certification.
High Density, two channels per unit.
Simplified installation using standard DIN-Rail and plug-in terminal blocks, with or without Power Bus, or customized Termination Boards.
Terminal block connections
2
1
4 3
6 5
Model: D6014
1 channel S
2 channels
D
Power Bus and DIN-Rail accessories:
Connector JDFT049 Cover and fix MCHP196
Terminal block male MOR017 Terminal block female MOR022
7 8
9 10
11 12
+ Input Ch 1 for 2 wires Transmitters
- Input Ch 1 for 2 wires Transmitters or
+ Input Ch 1 for External Powered Transmitters
+ Input Ch 2 for 2 wires Transmitters
- Input Ch 2 for 2 wires Transmitters or
+ Input Ch 2 for External Powered Transmitters
- Input Ch 1 for External Powered Transmitters
- Input Ch 2 for External Powered Transmitters
7
8
9
10
11
12
+ Output Ch 1
1
- Output Ch 1
2
+ Output Ch 2
3
- Output Ch 2
4
+ Power Supply 24 Vdc
5
- Power Supply 24 Vdc
6
Loading...