GlucoRxQ TD-4235B Operation Instruction Manual

311-4235200-XXX

L297*W420mm/銅版紙/100P/雙面/黑/3折/無

機器說明書/GlucoRX Q /英文(DiME)

K:100

JF

K:75 K:30 K:20

Part no.

Product name

Spec

Color

Designer

311-4235200-004

Version 1.0

2016/12

Dear owner of GlucoRx Q Blood Glucose Monitoring System.
Your system consists of three main products: the meter, test strips and control solution.
These products have been designed, tested and proven to work together as a system to
produce accurate blood glucose test results. Only use GlucoRx Q test strips and control
solution with the GlucoRx Q Blood Glucose Monitoring System.

Intended Use

This system is intended for external use (in vitro diagnostic use) only. It is used for the
quantitative measurement of glucose in samples of fresh capillary whole blood taken from
the finger, palm, forearm and upper arm. It is not intended to diagnose or screen for diabetes
mellitus, or to be used on neonates.

It allows blood glucose levels to be measured by people with diabetes at home and by
healthcare professionals in clinical settings as an aid to monitoring the effectiveness of
diabetes control.

This system provides you with plasma equivalent results and is displayed in millimoles of
glucose per litre of blood (mmol/L).

Read Before Use

Test Slot

1.

Display Screen

2.

M

Button

3.

SET Button

4.

Data Port

5.

Your meter will turn off automatically after 180 seconds without any action, or you can
press and hold the M for 3 seconds to turn off the meter.

NOTE

Test Result1.

Measuring Mode2.

Error Message3.

Blood Drop Symbol4.

Low Battery Symbol5.

Memory Symbol6.

Alarm Symbol 7.

Measurement Unit8.

Time Display9.

STEP 2. Setting the time format.

Press M to select the desired time format -- 12h or 24h. Press SET.

With the hour flashing, press M until the correct hour
appears. Press SET.
With the minute flashing, press M until the correct minute
appears. Press SET.

Press M to switch between buzzer beep on or off.
Press SET.

STEP 3. Set the hour and minute

STEP 4. Setting the buzzer beep

1. Start with your meter switched off. Insert a test strip to turn on the meter. The screen will
display “ ”.

Your meter provides you with four modes for measuring: General, AC, PC and QC.

You can switch between each mode by:

MODES

USE WHEN

General

AC

PC

QC

any time of day, regardless of time since last meal

no food intake for at least 8 hours

2 hours after a meal

testing with the control solution

IMPORTANT SAFETY INSTRUCTIONS

OPERATION INSTRUCTION

THE FOUR MEASURING MODES

APPEARANCE AND KEY FUNCTIONS OF THE METER

METER DISPLAY

2. Press M to switch between General, AC, PC and QC mode.

Your system measures the amount of sugar (glucose) in whole blood. Blood is applied to the
absorbent hole on the test strip and is automatically drawn into the reaction cell where the
reaction takes place.

The test strip consists of the following parts:

GlucoRx Q TEST STRIPS

STEP 1. Set the date

Start with the meter off (no test strip inserted). Press SET.

With the year flashing, press M until the correct year appears.
Press SET.

With the month flashing, press M until the correct month
appears. Press SET.

With the day flashing, press M until the correct day appears.
Press SET.

SETTING THE METER

1.

2.

3.

4.

5.

1.

2.

6.

7.

3.

4.

5.

8.

9.

Contact Bars

Insert this end of the test strip into your meter.
Push it in firmly until it will go no further.

Test Strip Handle

Hold this part to insert the test strip into the slot.

Absorbent Hole

Apply a drop of blood here.
The blood will be automatically absorbed.

Confirmation Window

This is where you confirm if enough blood has been
applied to the absorbent hole in the strip.

STEP 5. Setting the reminder alarm

Your meter has four reminder alarms. The meter will display "OFF",”AL1” and . If you
do not want to set an alarm, press SET to skip this step. Alternatively press M to select
"On" and press SET to proceed.
With the hour flashing, press M to select the correct hour. Press SET.
With the minute flashing, press M to select the correct minute. Press SET to confirm and
go to the next alarm setting.

STEP 2. Apply control solution

STEP 3. Read and compare the results

When the “ “ symbol appears on your display, press M and “QC” will appear on the display.
When the “QC” sign is displayed, your meter will not store your test result in memory. If you
decide not to perform a control solution test, press M again and the “QC” sign will disappear.

Shake your control solution vial thoroughly before use.
Squeeze out a drop and wipe it off, then squeeze out
another drop and place it on the tip of the vial cap. Hold
your meter to move the absorbent hole of the test strip to
touch the drop. Once the confirmation window fills
completely, your meter will begin counting down. To avoid
contaminating the control solution, do not directly apply
control solution onto a strip.

After your meter counts to 0, the result of the control solution
test will appear. Compare the result with the range printed on
your test strip vial. The result should fall within this range.

Out-of-range results

If you continue to have test results fall outside the range printed on the test strip vial, your
meter and/or strips may not be working properly. Do NOT test your blood. Contact
GlucoRx Customer Services on 01483-755133.

Every time you perform a control solution test, you must enter “QC” test mode so that
the test result will not be stored in the meter memory.

CAUTION

Preparing your Lancing Device for Blood Testing

Please follow the instructions in the lancing device insert for collecting a blood sample.
Never share a lancet or the lancing device. GlucoRx Lancing device is for self-use only.

STEP 1. Insert a test strip to turn on your meter

Wait for the meter to display “ ”.

STEP 2. Select the appropriate measuring mode by pressing M button

For selecting the measurement mode, please refer to the “FOUR MEASURING MODES”

TESTING YOUR BLOOD

Our control solution contains a known amount of glucose that reacts with test strips. By
comparing the result of the control solution test with the expected range printed on your
test strip vial label, you can check that your meter and test strips are working together as a
system and that you are performing the test correctly. It is very important that you perform
this simple check routinely to make sure you get accurate results.

HOW TO PERFORM A CONTROL SOLUTION TEST

STEP1. Insert test strip

Insert a test strip into the test slot with the contact bars end first and facing up. (Contact bars
must be inserted all the way into your meter or you may get an inaccurate test result.) The
meter turns on automatically and displays the following in sequence:

CHECKING YOUR SYSTEM WITH CONTROL SOLUTION

STEP 3. Apply blood sample

Obtain a drop of blood of at least 0.7 µL using your lancing device. Use the clear cap for sites
other than fingers and refer to the strip package insert for more details.

TD-4235B

10.

AC/PC Indicator10.

MONITORING SYSTEM

BLOOD GLUCOSE

Date obtained: / / Serial No:

Date obtained: / / Serial No:

WARRANTY REGISTRATION CARD

WARRANTY CERTIFICATE

[ Dealer’s Portion ]

[ Owner’s Portion ]

Product Name:

Owner’s Name:

Address:

Tel No: (M)

(H)

(W)

Email:

Date of Birth:

Gender:

M F

Blood glucose testing frequency:

Insulin dependent?

Day

Day

Month

Month

Year

Year

*IMPORTANT: To qualify for the warranty, please fill in this card and mail to us within 6 months from date product obtained.

*NOTE: Please produce this card for warranty service.

Product Name:

Owner’s Name:

Address:

Tel No: (M)

(H)

(W)

Email:

Date of Birth:

Gender:

M F

Blood glucose testing frequency:

Insulin dependent?

GP Surgery name and Address:

GP Surgery name and Address:

YEAR WARRANTY