GLP YPOC 575, YPOC 575 PRO Instruction Manual

Instruction Manual

from software version 1.0
(instruction version 1.25)

e-mail: [e-mail]

Internet: http://www.GLP.de

This side is intentionally unlabelled.

GLP  German Light Production (V1.25) 2

Table of contents

1 Description of Device............................................................................................. 5

1.1 Safety Instructions............................................................................................ 6

2 Preparation and Installation .................................................................................. 7

2.1 Mounting .......................................................................................................... 7

2.1.1 Clamps .................................................................................................. 7

2.2 Secure the YYPPOOCC 557755...................................................................................... 8

2.3 Connections ..................................................................................................... 9

2.3.1 Power supply ......................................................................................... 9

2.3.2 DMX....................................................................................................... 9

2.4 Fuse ................................................................................................................. 9

3 The Menu Field ..................................................................................................... 10

3.1 Adjust the DMX- Address (D001)..................................................................... 11

3.2 The Test Program (TEST)................................................................................ 11

3.3 The Audio Program (AUDI).............................................................................. 11

3.4 Lamp On/Off (LAMP) ........................................................................................ 12

3.5 Reset (RESE) ................................................................................................... 12

3.6 Running time of lamp and unit (TIME) ............................................................. 12

3.7 Invert Pan Movement (RPAN)........................................................................... 12

3.8 Invert Tilt Movement (RTLT) ............................................................................ 13

3.9 Special Functions (SPEC) ................................................................................ 13

3.9.1 Manual Drive

3.9.2 Lamp On automatically

3.9.3 Lamp Off via DMX (DLOF) ..................................................................... 14

3.9.4 DMX Input (DMXI) ................................................................................. 14

3.9.5 Display (DISP) ...................................................................................... 15

3.9.6 Fixture Temperature (TEMP).................................................................. 15

3.9.7 Fan Control (FANS) ............................................................................... 15

3.9.8 Adjustments and Calibrations (ADJU).................................................... 16

(MANU) ............................................................................. 13

(LAAU).............................................................. 13

3.9.9 Default Settings (DFSE)......................................................................... 16

3.9.10 Feedback (FEED) .................................................................................. 17

3.9.11 Correction of faults (EFLG) .................................................................... 17

3.10 Error and Information Messages.................................................................... 17

4 DMX Channel Selection (DMX Protocol)............................................................. 18

5 Change the Lamp.................................................................................................. 21

GLP  German Light Production (V1.25) 3

5.1 Safety Regulations ......................................................................................... 21

5.2 Realize the Lamp Change..............................................................................22

6 Change a Gobo ..................................................................................................... 23

6.1 Safety Regulations ......................................................................................... 23

6.2 Realize the Gobo Change .............................................................................. 23

7 Maintenance and Cleaning the YYPPOOCC 557755 ..........................................................24

7.1 Safety Regulations ......................................................................................... 24

7.2 Circumference and Interval (rule-of-thumb).................................................... 24

7.3 Cleaning the Optical System .......................................................................... 25

8 Technical Specification........................................................................................ 26

9 Index ......................................................................................................................27

GLP  German Light Production (V1.25) 4

1 Description of Device

1

4

1. Moving Head

2. Carrying handles

3. Base

4. Arm

3

2

5. Up- button

6. Down- button

7. Enter- button

8. Mode- button

9. LED- Display

10. Software-Update

connector

11. Microphone- Intensity

12. DMX- Input

13. DMX- Output

14. Power On/Off

15. Fuse F3,15 A

16. Fan (air inlet)

12

11

10

9

87 65

DMX IN DMX OUT

MaxMin

Mic Sensitive

Serial
number:

MODE EN TER UP DOWN

O

M

D

E

E

R

3

H

S

12

Software Update

D

O

W

N

E

N

T

13

FUSE:
T3.1 5A @2 50V

LAMP:

U

P

1.Ground

2.Data-

3.Data+

U

P

MSD 250W

Power input

14

POWER

210V~

230V~

250V~

50Hz

60Hz

Fuse

FUSE

15

16

GLP  German Light Production (V1.25) 5

1.1 Safety Instructions

The YYPPOOCC 557755 is a High-Tech Product. To guarantee a smooth
operation, it is necessary to keep following rules.
The manufacturer of this device will not take responsibility of
damages through disregard of the information in this manual.
Warranty adjustments will be canceled.

1. Make sure before putting into operation, that the fan and the air inlets are

clean and not blocked by anything.

2. Attention: Don’t touch the device during the operation. This can cause

injuries or damages.

3. Unplug the YYPPOOCC 557755 from the AC outlet before any service.

4. It is necessary to wait at least 30 minutes after disconnecting the AC before

you open the YYPPOOCC 557755. Please do not touch the bulb of the lamp if you are

not absolutely sure it is cold. -Danger of BURNING-

5. Never look directly into the beam of the lamp. You risk injury of your retina and

blindness.

6. Pay attention of the maximum lamp operation time. You have to change it if

the lamp shows any deformations or damages. The same is with all glass

components, color filters, lenses and mirrors.

7. To allow a secure operation, follow also the Installation guide described in

chapter 2. Operating the YYPPOOCC 557755 without suited safety aids like Safety

cables or clamps/hooks can increase the risk of an accident.

8. The installation should be done by qualified staff only. You need to pay

attention to the common rules of technology that are not explicit mentioned in

this manual.

9. Use only original spare parts. Any structural modification will cancel all

warranty adjustments.

Attention: Laser of class 3R may
injure your retina after a short resi-

LASE RSTRAHLUNG

NICHT IN DEN STRAHL BLICKEN

LASER KLASSE 3R

NACH DIN-EN 60825-1/11:2001

λ

P 5mW; = 635-650 nm

0

dence time even without any optical
instrument. Avoid any direct ex-
posure of your eyes!

GLP  German Light Production (V1.25) 6

2 Preparation and Installation

2.1 Mounting

The YYPPOOCC 557755 is fully operational whether it hangs or is mounted to the wall. It

can also be operated while standing on the floor. Keep a safety distance of 0.5 m

towards any easy inflammable materials (decoration etc.). Install a safety wire that

can hold at least 10 times the weight of the fixture. Never use the carrying handles

for secondary attachment.

Pay attention to the regulations of: BGV C1 (former VBG 70)

and DIN VDE 0711-217. Regulations of show laser BGV B2

(11.2001), E DIN 56912 part 6, DIN-EN 60825 part 1+2.

2.1.1 Clamps

There are two major possibilities to mount the YYPPOOCC 557755 together with

clamps. Camlock system or direct mounting of clamps. In both cases you

have to regard a sufficient stability of the system. For installation

instructions please see also printing on the backside of the case.

a) Camlock System: This system allows you a fast and efficient setup of

clamps. Attach the two camlocks to designated position on the backside

GLP  German Light Production (V1.25) 7

The installation should be done by qualified staff only.

of the case and close the locks by turning them 90°. Verify the secure fit

of the camlock system. The clamps themselves are directly attached

permanently on the camlocks.

90°

b) Use two clamps direct on the backside of the YYPPOOCC 557755 to mount the

unit on a truss (each two opposite threads max. M10x20).

4x M10x20mm

4x Camlock

2.2 Secure the YYPPOOCC 557755

Regardless of the rigging of the YYPPOOCC 557755 you have to use a stipulated safety

wire. Therefore you have to thread to safety wire through to two provided holes on

the backside of the fixture and connect it with the truss-support. Pay attention to a

safe and proper fastening.

GLP  German Light Production (V1.25) 8

2.3 Connections

2.3.1 Power supply

230 Volt, 50 Hz,

Connected load 700W <=> 3.1 A (blind current compensation).

or 115V, 60 Hz

Connected load 700W <=> 6.2 A (blind current compensation).

Please see printing on the case for the right Power supply !

2.3.2 DMX

DMX 512 Standard input/output. See also printing on the case for the right

pin assignment.

[+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1

The DMX- Addressing starts at the DMX- Address [001].

2.4 Fuse

The YYPPOOCC 557755 electronic system is protected by a 5x20 mm fuse.

230V / T 5A (EU model) or 115V / T 10A (US model)

Please see the printing on the YYPPOOCC 557755 for more details.

Attention:

• Disconnect AC outlet before changing a fuse!

• Use only the original declared fuse type!

GLP  German Light Production (V1.25) 9

3 The Menu Field

You find the control board on the side part of the base. It allows you to make
all necessary adjustments of the YYPPOOCC 557755.. With the Mode-key you get into
the main menu. Afterwards you can navigate through the menu with the
Up/Down-keys. Push the Enter-key to get in the next menu level or to
confirm your settings. Make them and set functions ON/OFF with the
Up/Down-keys. Confirm and save it with the Enter-key (the display shows

OK). Push the Mode-key to cancel the entry and go back to the main menu.

Level 1 Level 2 Level 3

D001
TEST
AUDI ASLW

AFST
MSTR
SVPT

SIZE
LAMP
RESE
TIME POWR

LA1

LA2
RPAN
RTLT
SPEC MANU

LAAU

DLOF

DMXI

DISP D ON

REV

TEMP

FANS HIGH

REG

LOOF

Å DOWN - UP Æ

LOHI

ADJU CODE xxxx

COLO

GOB1

GOB2

PRIS

SHTR

POFS

TOFS

ARES

clre

facc

VTIL

VTOP

VBOT

FASP

DFSE

FEED

EFLG

Remark

Define the DMX start address
Test program of all functions
Self-running audio program (slow)
Self-running audio program (fast)
Master for the audio program
Basic position for the audio program
Size for the audio program (NORM-BIG-MIDL-SMAL)
Switch on/of the lamp direct at the YYPPOOCC 557755
Reset
Running time of the fixture (no destructible)
Running time of the lamp (erasable)
Running time of the lamp (no destructible)
Reverse Pan-direction
Reverse Tilt-direction
Manual drive of all device functions
Automatic lamp start
Switch off lamp via DMX
Reed out actual DMX-values
Display On/Off
Twist the display
Reed out internal temperature
Maximum cooling fan velocity
Automatic cooling fan control
Low cooling fan speed Æ lamp off
Low cooling fan speed Æ automatic
Use the code for entering the calibration menu (for authorized

person only)
Calibration of the color wheel

Calibration of the gobo wheel 2
Calibration of the gobo wheel 2
Calibration of the prism wheel
Calibration of the shutter
Calibration of the Pan-Offsets
Calibration of the Tilt-Offsets
Adjust Reset (wheels stand still after the reset)
Settings in the internal memory (super-user only)
Must read on. Protected with a code.
Software version Tilt-board
Software version Head-board
Software version Base-board
Indication of the Fan speed
Call on the default function values
Pan/Tilt feedback (error correction) On/Off
Correction of faults

Mode-key Enter-key Down-key

LED-Display

MODE ENTER UP DOWN

M O D E E N T E R U P D O W N

Up-key

GLP  German Light Production (V1.25) 10

3.1 Adjust the DMX- Address (D001)

Right after turning on the YYPPOOCC 557755 you can see the current DMX- Address. If

there is no DMX- Signal the display flashes.

D001

For the address setting please follow this procedure:

1. Switch On the YYPPOOCC 557755 and wait until the fixture reset has finished ('RESE' is

flashing in the display).

2. Press the Mode-key in order to access the main menu. Browse through the

menu by pressing the Up/Down-keys until the display shows D001. Confirm by

pressing the Enter-key (the decimal point is flashing)

3. Use the Up/Down-keys to select the desired address. Confirm the setting by

pressing the Enter-key (the display shows OK) or press the Mode-key to

cancel.

The DMX- Address is stored also while switching off the YYPPOOCC 557755!

3.2 The Test Program (TEST)

test

The Test-Program allows you to run a complete self test procedure of all

functions. Press Enter to confirm or Mode to cancel.

3.3 The Audio Program (AUDI)

Audi

The Audio-menu allows you to run a stand alone audio program. This chaser can
run either fast or slow. AFST: Every soundimpulse on step of the chaser. Aslw:

Every second soundimpulse one step of the chaser.

Additional you can choose a basic position for this audio chaser. Use therefore

either the internal manual mode or an external controller to set the desired

Pan/Tilt position. Confirm this setting in the SVPT menu by pressing the Enter-key.

You can also set the size of the audio chaser in the SIZE menu. You have the

choice between: NORM (no basic position has to bee chosen), 'BIG', 'MIDL' and

'SMAL').

GLP  German Light Production (V1.25) 11

If you want to run the systems simultaneously, one of the YYPPOOCCss must be

switched as the master. All others must be "Slave" Master = OFF. Notice: The

Audio function is only working if no DMX is connected. This function can work e.g.

on small events or as an emergency program.

3.4 Lamp On/Off (LAMP)

LAMP

Use the Up/Down-keys to select lamp On or lamp Off Press Enter to confirm or

Mode to cancel and return to the main menu. (The lamp

OFF command is only

working if the shutter is closed at the same time. Use an external controller or the

manual drive mode, see 3.9.1)

3.5 Reset

(RESE)

RESE

Press the Enter-key to run a reset of all fixture functions (RST is shown in the

display).

3.6 Running time of lamp and unit (TIME)

TIME

By this option can read out three different running times of the fixture.

POWR

Running time of the fixture (no destructible).

LA 1

Running time of the lamp (erasable). Push the Up/Down-keys at one
time to delete this running time.

LA 2

Running time of the lamp (no destructible).

3.7 Invert Pan Movement (RPAN)

RPAN

This function allows you to invert the Pan movement. Use the Up/Down-keys to
select invert On or Off. Press Enter to confirm or Mode to cancel and return to the

main menu.

GLP  German Light Production (V1.25) 12

3.8 Invert Tilt Movement (RTLT)

RTLT

This function allows you to invert the Tilt movement. Use the Up/Down-keys to
select invert On or Off. Press Enter to confirm or Mode to cancel.

3.9 Special Functions (SPEC)

SPEC

This menu allows you to enter further special functions of the YYPPOOCC 557755..

In detail they are:

3.9.1 Manual Drive (MANU)

MANU

This function allows you to drive all the fixture functions manually. Select

the desired function with the Up/Down-keys and confirm with Enter. Now

choose the desired value with the Up/Down-keys and confirm again with

Enter or cancel and return to the menu with the Mode-key.

Function Value Remark

PAN 000 - 255
TILT 000 - 255
COLO 000 - 255
GOB1 000 - 255
GROT 000 - 255
GOB2 000 - 255
PRIS 000 - 255
SHUT 000 - 255

DIMR 000 - 255
FOCU 000 - 255
SPEC 000 - 255
LASR 000 - 255

Pan Position
Tilt Position
Color wheel
Gobo wheel 1
Gobo rotation
Gobo wheel 2
Prism rotation
Shutter / Strobe function (the lamp strikes at

DMX 255 if dimmer is "open" = DMX 255)
Dimmer

Focus
Lamp Off, Reset, ...
Laser

3.9.2 Lamp On automatically (LAAU)

LAAU

This function enables to switch On the lamp automatically after switching

GLP  German Light Production (V1.25) 13

On the fixture. Use the Up/Down-keys to select ON if you want to switch on
the lamp automatically after switching on the fixture or Off if you don't want

this function. Press Enter to confirm or Mode to cancel and return to the

menu.

If you have chosen off you have the possibility to start the lamp either via

DMX or direct at the YYPPOOCC 557755 in the Lamp menu.

3.9.3 Lamp Off via DMX (DLOF)

DLOF

This function enables to switch off the lamp via DMX or not. Use the
Up/Down-keys to select ON if you want to switch off the lamp via DMX or

Off if you don't want this function. Press Enter to confirm or Mode to

cancel and return to the menu.

If you have chosen off you have the possibility to switch off the lamp either

direct at the YYPPOOCC 557755 in the Lamp menu or switch off the main switch.

3.9.4 DMX Input (DMXI)

DMXI

Readout DMX values of each channel received by the fixture. Use the

Up/Down-keys to select desired channel and press Enter to read its value.

Function Value Remark

PAN 000 - 255
TILT 000 - 255
COLO 000 - 255
GOB1 000 - 255
GROT 000 - 255
GOB2 000 - 255
PRIS 000 - 255
SHUT 000 - 255
DIMR 000 - 255
FOCU 000 - 255
SPEC 000 - 255
MOVE 000 - 255
SPED 000 - 255
LasR 000 - 255

Pan Position
Tilt Position
Color wheel
Gobo wheel 1
Gobo rotation
Gobo wheel 2
Prism wheel
Shutter / Strobe function
Dimmer
Focus
Lamp Off, Reset, ...
Movement
Speed Pan/Tilt
Laser

GLP  German Light Production (V1.25) 14

3.9.5 Display (DISP)

DISP

Use this function to choose between different display indications. Use the

Up/Down-keys to select desired function and press Enter to confirm or

Mode to cancel and return to the menu.

D ON Display On/Off (If you've chosen off, the display will go out within

15 seconds after the last input. The next key touch will reactivate
the display).

REV

Turn around the display

3.9.6 Fixture Temperature (TEMP)

TEMP

This function allows you to read out the actual temperature of the YYPPOOCC

5. Press Enter to confirm or Mode to cancel. Inside temperatures below

55775

80°C are not critical. 80°C and more lead the lamp being switched off at a

critical point. Please note for a save operation that the outside temperature

should not exceed 45°C.

3.9.7 Fan Control (FANS)

FANS

By using this function you can choose between 4 types of fan speed

operations. Use the Up/Down-keys to select desired function and press

Enter to confirm or Mode to cancel and return to the menu.

HIGH

REG

The cooling fan works continuously at max. speed.

The fan automatically raises its speed in order to control inside
temperature of the fixture.

LOOF

The fan keeps the adjusted low speed until the temperature
exceeds max. inside temperature, then the YYPPOOCC 557755 automatic­ally switch off the lamp.

LOHI

The fan keeps the adjusted low speed until the temperature
exceeds max. inside temperature, then the YYPPOOCC 557755 automatic­ally switch from low to high fan speed.

In addition to these settings, you can set to fan speed to minimum via DMX

(Special channel 13, value 224..229). This will last until a temperature of

90° is reached.

GLP  German Light Production (V1.25) 15

3.9.8 Adjustments and Calibrations (ADJU)

ADJU

By this function you can adjust and calibrate the positions of the different

wheels and other motors. This can be necessary after a service or repair

work.

For this function you have to entry the fixture code. This work should be

done only by authorized persons.

Use the Up/Down-keys to select desired function and press Enter to

confirm or Mode to cancel and return to the menu. Use now the Up/Down-

keys to set the adjustment values and confirm once more with the Enter-

key or cancel with the Mode-key.

Function Value Remark

ADJU CODE xxxx

COLO - 99 - + 99
GOB1 - 99 - + 99
GOB2 - 99 - + 99
PRIS - 99 - + 99
SHTR - 99 - + 99
POFS - 99 - + 99
TOFS - 99 - + 99
ARES - 99 - + 99
CLRE

Adjustments in the internal circuit.

FACC - 99 - + 99
VTIL - 99 - + 99
VTOP - 99 - + 99
VBOT - 99 - + 99
FASP - 99 - + 99

Adjustments in the internal setup are code protec­ted (for authorized persons only).

Adjustment of the Color wheel
Adjustment of the Gobo wheel 1
Adjustment of the Gobo wheel 2
Adjustment of the Prism wheel
Adjustment of the Shutter
Adjustment of the Pan-Offsets
Adjustment of the Tilt-Offsets
Adjust Reset (wheels stand still after the reset)

Must switched to ON (code protected)
Software version of Tilt-board
Software version of Head- board
Software version of Base- board
Indication of the Fan-Speed

3.9.9 Default Settings (DFSE)

DFSE

Press Enter to reset all fixture personalities (not the adjusted functions) to
the default values. On the display will appear ok to indicate that the de-

faults are set.

Function Display Default Settings

DMX Address
Pan reverse

Tilt reverse

GLP  German Light Production (V1.25) 16

D001 D001
RPAN ON OFF 9

RTLT ON OFF 9

Automatic lamp on
Lamp on via DMX
Display
Cooling fan
Feedback

3.9.10 Feedback (FEED)

FEED

The YYPPOOCC 557755 is provided with a automatic position correction (feedback)
for the Pan and Tilt movement. Use the Up/Down-keys to select ON if you
want to enable the feedback function or Off if you don't want this function.

Press Enter to confirm or Mode to cancel and return to the menu.

3.9.11 Correction of faults (EFLG)

EFLG

(Function available for authorized persons only)

LAAU ON OFF 9
DLOF ON 9 OFF
DISP D ON 9
FANS

HIGH

REG 9

LOOF LOHI

FEED ON 9 OFF

3.10 Error and Information Messages

HEAt

LaeR

OTMP

RsER

This message appears if you try to switch on the lamp within 5 minutes
after having switched off (lamp too hot). The message will appear on
the display if the lamp doesn’t ignite within 20 seconds. The fixture will
store this command and automatically ignite the lamp after 5 minutes.

After the ignition of the lamp was two times not successful the display
will show LAER. That means the lamp could be damaged or even

missed, the fixture is overheating or there could be a failure on the
igniter or ballast. Switch off the power supply and solve the possible
problem.

This error message informs you that the fixture was overheating and
that the relay switches off the lamp. Pleas look for possible reasons
(fan faulty, air in/outlets blocked or very dirty, lamp broken or very old,
too high ambient temperature. Switch off the power supply and solve
the possible problem.

This message informs you that one of the fixture function wasn’t able to
do its reset correct (magnetic sensor, stepping motor, driver on the
PCB, cables, etc.). Repair the defect and start the fixture again.

GLP  German Light Production (V1.25) 17

4 DMX Channel Selection (DMX Protocol)

Channel Function Time and Value DMX HEX %

1) PAN­ coarse

2) PAN-fine

3) Tilt­ coarse

4) Tilt-fine

5) Color

open / color 1 (fast) 2..3 02..03 1,0
color 1, Brilliant Blue (fast)
color 1 / color 2 (fast) 6..7 06..07 2,5
color 2, Blue (fast) 8..9 08..09 3,3
color 2 / color 3 (fast) 10..11 0A..0B 4,1
color 3, Blue Purple (fast) 12..13 0C..0D 4,9
color 3 / color 4 (fast) 14..15 0E..0F 5,7
color 4, Magenta (fast) 16..17 10..11 6,5
color 4 / color 5 (fast) 18..19 12..13 7,3
color 5, Pink (fast) 20..21 14..15 8,0
color 5 / color 6 (fast) 22..23 16..17 8,8
color 6, Orange (fast) 24..25 18..19 9,6
color 6 / color 7 (fast) 26..27 1A..1B 10,4
color 7, Canary (fast) 28..29 1C..1D 11,2
color 7 / color 8 (fast) 30..31 1E..1F 12,0
color 8, Italian Blue (fast) 32..33 20..21 12,7
color 8 / color 9 (fast) 34..35 22..23 13,5
color 9, Turquoise (fast) 36..37 24..25 14,3
color 9 / color 10 (fast) 38..39 26..27 15,1
color 10, Jade (fast) 40..41 28..29 15,9
color 10 / color 11 (fast) 42..43 2A..2B 16,7
color 11, Red (fast) 44..45 2C..2D 17,5
color 11 / open (fast) 46..47 2E..2F 18,2
open (fast) 48..63 30..3F 19,0
open (slow) 64..65 40..41 25,3
open / color 1 (slow) 66..67 42..43 26,1
color 1, Brilliant Blue (slow)
color 1 / color 2 (slow) 70..71 46..47 27,6
color 2, Blue (slow) 72..73 48..49 28,4
color 2 / color 3 (slow) 74..75 4A..4B 29,2
color 3, Blue Purple (slow) 76..77 4C..4D 30,0
color 3 / color 4 (slow) 78..79 4E..4F 30,8
color 4, Magenta (slow) 80..81 50..51 31,6
color 4 / color 5 (slow) 82..83 52..53 32,4
color 5, Pink (slow) 84..85 54..55 33,1
color 5 / color 6 (slow) 86..87 56..57 33,9
color 6, Orange (slow) 88..89 58..59 34,7
color 6 / color 7 (slow) 90..91 5A..5B 35,5
color 7, Canary (slow) 92..93 5C..5D 36,3
color 7 / color 8 (slow) 94..95 5E..5F 37,1
color 8, Italian Blue (slow) 96..97 60..61 37,8
color 8 / color 9 (slow) 98..99 62..63 38,6
color 9, Turquoise (slow) 100..101 64..65 39,4
color 9 / color 10 (slow) 102..103 66..67 40,2
color 10, Jade (slow) 104..105 68..69 41,0

0 .. 530° min. 2,65 s 0..255 00..FF 0..100

High- Pos ... High- Pos + 2,1° (16 Bit) 0..255 00..FF 0..100
0 .. 285° min. 1,8 s 0..255 00..FF 0..100

High- Pos … High- Pos + 1,1° (16 Bit) 0..255 00..FF 0..100
open (fast) 0..1 00..01 0,2

Chaser from color to
color max. 140 BPM
=> 0,43 s

Chaser from color to
color max. 70 BPM
=> 0,86 s

4..5 04..05 1,8

68..69 44..45 26,9

GLP  German Light Production (V1.25) 18

Channel Function Time and Value DMX HEX %

color 10 / color 11 (slow) 106..107 6A..6B 41,8
color 11, Red (slow) 108..109 6C..6D 42,5
color 11 / open (slow) 110..111 6E..6F 43,3
open (slow) 112.127 70..7F 44,1
color rotation STOP 128..129 80..81 50
color rotation, slow-fast, CW min. 1,4 turns/h 130..191 82..BF 51..75
color rotation, fast-slow, CCW max. 2,9 turns/sec. 192..253 C0..FD 76..98
Audio color chaser slow each 4th sound impulse

Æ new color

Audio color chaser fast each sound impulse Æ

new color

6) Gobo 1

Gobo 1 (open, fast) 0..7 0..7 0..2,9
Gobo 2 (fast) 8..15 8..F 3..5,9
Gobo 3 (fast)
Gobo 4 (fast) 24..31 18..1F 9..11,9
Gobo 5 (fast) 32..39 20..27 12..14,9
Gobo 6 (fast) 40..47 28..2F 15..17,9
Gobo 7 (fast) 48..55 30..37 18..20,9
Gobo 8 (fast) 56..63 38..3F 21..23
Gobo 1 (open, slow) 64..71 40..47 24..26,9
Gobo 2 (slow) 72..79 48..4F 27..29,9
Gobo 3 (slow)
Gobo 4 (slow) 88..95 58..5F 34..36,9
Gobo 5 (slow) 96..103 60..67 37..39,9
Gobo 6 (slow) 104..111 68..6F 40..42,9
Gobo 7 (slow) 112..119 70..77 43..45,9
Gobo 8 (slow) 120..127 78..7F 46..49
Gobo rotation STOP 128..129 80..81 50
Gobo rotation, slow-fast, CW min. 1,4 turns/h 130..191 82..BF 51..75
Gobo rotation, fast-slow, CCW max. 1.0 turns/sec. 192..253 C0..FD 76..98
Audio gobo chase, slow each 4

Chaser from gobo to
gobo max. 100 BPM
=> 0,6 s

Chaser from gobo to
gobo max. 40 BPM
=> 1,51 s

th

sound impulse

Æ new gobo

Audio gobo chase, fast each sound impulse Æ

new gobo

7) Gobo
Posi./Rot

Gobo position 0 ... 540° 0..127 00..7F 0..49
Gobo rotation STOP 128..129 80..81 50
Gobo rotation, slow-fast, CW min. 2,0 turns/h 130..191 82..BF 51..75
Gobo rotation, fast-slow, CCW max. 3,8 turns/sec. 192..253 C0..FD 76..100
Audio gobo rotation, slow each 4

th

sound impulse

Æ new position

8) Gobo 2

Gobo 1 (open, fast) 0..3 0..3 0..1
Gobo 2 (fast) 4..7 4..7 2..2,9
Gobo 3 (fast)
Gobo 4 (fast) 12..15 C..F 5..5,9
Gobo 5 (fast) 16..19 10..13 6..7
Gobo 6 (fast) 20..23 14..17 8..8,9
Gobo 7 (fast) 24..27 18..1B 9..10,9
Gobo 8 (fast) 28..31 1C..1F 11..12
Gobo 9 (fast) 32..35 20..23 13..13,9
Gobo 10 (fast) 36..63 24..3F 14..24,9
Gobo 1 (open, fast) 64..65 40..41 25..25,9
Gobo 1 (open, slow) 66..67 42..43 26..26,9
Gobo 2 (slow)

Chaser from gobo to
gobo max. 100 BPM
=> 0,6 s

Chaser from gobo to
gobo max. 40 BPM

254 FE 99

255 FF 100

16..23 10..17 6..8,9

80..87 50..57 30..33,9

254 FE 99

255 FF 100

254 FE 99

8..11 8..B 3..4

68..71 44..47 27..27,9

GLP  German Light Production (V1.25) 19

Channel Function Time and Value DMX HEX %

9) Shutter

10) Dimmer

11) Focus

12) Prism

13) Special

Gobo 3 (slow)

=> 1,51 s

72..75 48..4B 28..29
Gobo 4 (slow) 76..79 4C..4F 30..30,9
Gobo 5 (slow) 80..83 50..53 31..32
Gobo 6 (slow) 84..87 54..57 33..34
Gobo 7 (slow) 88..91 58..5B 35..35,9
Gobo 8 (slow) 92..95 5C..5F 36..37
Gobo 9 (slow) 96..99 60..63 38..38,9
Gobo 10 (slow) 100..127 64..7F 39..50
Gobo rotation STOP 128..129 80..81 50
Gobo rotation, slow-fast, CW min. 1,4 turns/h 130..191 82..BF 51..75
Gobo rotation, fast-slow, CCW max. 1.0 turns/sec. 192..253 C0..FD 76..98
Audio gobo chase, slow each 4

th

sound impulse

254 FE 99

Æ new gobo

Audio gobo chase, fast each sound impulse Æ

255 FF 100

new gobo

Audio gobo rotation, fast each sound impulse Æ

255 FF 100

new position
Shutter closed 0..15 00..0F 0..6
Random Strobe (different pattern) 16..31 10..1F 7..11,9
Strobe Pulse effect , slow - fast min. frequent 0,7 Hz 32..47 20..2F 12..12,9
Strobe effect , slow - fast max. frequent 10 Hz 48..239 30..EF 13..93
Shutter open (lamp start) 240..255 F0..FF 94..100
Dimmer closed (0%) 0..3 0..3 0..1
Dimmer 1%...99% movement time 0,3 sec. 4..251 4..FB 2..98
Dimmer open (100%) 252..255 FC..FF 99..100
in - out full distance 1,5 sec. 0..255 0..FF 0..100
Prism swing out 0..5 00..02 0..2
Prism position 0 ... 540° 6..129 00..7F 0..50
Prism rotation, slow-fast, CW min. 1,6 turns/h 130..191 80..BF 51..75
Prism rotation, fast-slow, CCW max. 4,4 turns/sec. 192..253 C0..FD 76..100
Audio prism rotation, slow each 4

th

sound impulse

254 FE 99

Æ new prism
Audio prism rotation, fast each sound impulse Æ

255 FF 100

new prism
no function 0..15 00..0F 0..6
Gobo-shake +/- 10°

slow – fast
Gobo-shake +/- 20°
slow – fast
Gobo-shake +/- 30°
slow – fast
Color-chaser C / C+1
slow – fast
Color-chaser C / C+2
slow – fast
Audio Pan / Tilt slow each 4

3,5 moves / min. up to

60 moves / max.

3,5 moves / min. up to

60 moves / max.

3,5 moves / min. up to

60 moves / max.

0,7 BPS ... 2,3 BPS

=> 1,43 s ... 0,43 s

0,7 BPS ... 2,0 BPS

=> 1,43 s ... 0,5 s

th

sound impulse

16..31 10..1F 7..12

32..47 20..2F 13..18

48..63 30..3F 19..24

64..79 40..4F 25..31

80..95 50..5F 32..37

96..111 60..6F 38..43

Æ new position
Audio Pan / Tilt fast each sound impulse Æ

112..127 70..7F 44..50

new position
no function 128..249 80..E5 50..97
fan on min. as long as temp. < 90°C 224..229 E0..E5 88..90
Lamp OFF (min. 3 sec.) 230..249 E6..F9 92..97
Reset

250..255 FA..FF 98..100

GLP  German Light Production (V1.25) 20

Channel Function Time and Value DMX HEX %

14) Move­ment Movement Size Phase

15) Speed

Pan/Tilt

16) Laser

Lamp ON

Lamp OFF

no movement 0 00 0

PAN 1 0° 01..01 01..01 0,5
1 90° 02..03 02..03 1,0
1 180° 04..05 04..05 1,7
1 270° 06..07 06..07 2,5
PAN 2 0° 08..09 08..09 3,3
2 90° 10..11 0A..0B 4,1
2 180° 12..13 0C..0D 4,9
2 270° 14..15 0E..0F 5,7
PAN 3 0° 16..17 11..11 6,5
3 90° 18..19 12..13 7,3
3 180° 20..21 14..15 8,0
3 270° 22..23 16..17 8,8
PAN 4 0° 24..25 18..19 9,6
4 90° 26..27 1A..1B 10,4
4 180° 28..29 1C..1D 11,2
4 270° 30..31 1E..1F 12
TILT size / phase see also PAN 32..63 20..3F 13..25
PAN / TILT size / phase see also PAN 64..95 40..5F 26..37
PAN / TILT (inverse) size / phase see also PAN 96..127 60..7F 38..50
Circle size / phase see also PAN 128..159 80..9F 51..62
Circle (inverse) size / phase see also PAN 160..191 A0..BF 63..75
lying eight size / phase see also PAN 192..223 C0..DF 76..87
random movement size see also PAN 224..255 E0..FF 88..100

Pan/Tilt relative movement 0..15 00..0F 0..6
Pan/Tilt slow – fast
Use this channel 14) also for the speed
of the movements (channel 13).

Laser OFF 0..15 00..0F 0..6
Laser flashing random 16..31 10..1F 7..12
Audio Laser 32..47 20..2F 13..18
Blinking slow - fast 48..127 30..7F 19..50
Flashing slow - fast 128..239 80..EF 51..93
Laser ON 240..255 FO..FF 94..100

Shutter open 240..255 F0..FF 94..100
Channel 13 ( min. 3 sec. ) (only if
shutter is closed, channel 10 = 0 ..15)

Pan min. 530° = 200 s
Pan max. 530° = 2,65 s
Tilt min. 285° = 110 s
Tilt max. 285° = 1,8 s

230..249 6E..9F 92..97

16..255 10..FF 7..100

5 Change the Lamp

For a frictionless operation pleas read this chapter carefully and follow all instructions.

5.1 Safety Regulations

• Pull out the main plug!

GLP  German Light Production (V1.25) 21

• Wait min. 20 minutes after the last operation to cool down the fixture.

• Don’t touch the bulb of the lamp with bare fingers (this can cause damages).

• Before you put the YYPPOOCC 557755 into operation close the casing, otherwise your

retina can be hurt!

5.2 Realize the Lamp Change

1. Pull out the main plug!

2. The lamp can be changed in a very comfortable way directly from the backside

of the case without opening the head.

3. Open the four screws (1,2,3 and 4) of the backside lamp sheet and remove it

carefully.

4. Remove the old or broken lamp by opening the two sidewise lamp screws.

Attention: The glass bulb of the lamp can splinter. For that reason remove the

lamp with safety gloves or some cloth.

5. Put in the new lamp securely with a tight fit into the socket and close the two

lamp screws. The lamp filler neck must not in the direction lamp or lenses.

Attention: Use only the original lamp type!

6. Pull the lamp holder safely back in the shaft and close the four screws.

7. The running time of the lamp LA1 can be reseed in the Time Menu.

GLP  German Light Production (V1.25) 22

6 Change a Gobo

The YYPPOOCC 557755 is fitted with standard gobos (outside diameter 27 mm, image size 23

mm). You can use ether steel or glass gobos.

6.1 Safety Regulations

• Pull out the main plug!

• Wait min. 20 minutes after the last operation to cool down the fixture.

• Before you put the YYPPOOCC 557755 into operation close the casing, otherwise your

retina can be hurt!

6.2 Realize the Gobo Change

1. Pull out the main plug!

2. Open the upper shell of the head casing by loosening the 4 Phillips screws.

Two on the front side and 2 on the back side of the head.

3. Rotating Gobo-wheel: Remove the gobo out of the centric spring. Afterwards

the gobo can be changed outside.

4. Fixed Gobo-wheel: Remove the gobo directly out of the Gobo-spring.

5. Change the desired gobo and fix it again under the spring.

6. Close the YYPPOOCC 557755 in reverse order.

Wheel with rotating Gobos Wheel with non rotating Gobos

Attention:

If you use glass gobos, the non-vaporized side must be fitted towards the
lamp direction.

GLP  German Light Production (V1.25) 23

Maintenance and Cleaning the YYPPOOCC 557755

77

It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid

residues must not built up on or within the fixture. Otherwise the fixture's light-output will

be significantly reduced. Regular cleaning will not only ensure the maximum light-

output, but will also allow the fixture to function reliable throughout its life.

A soft lint-free cloth moistened with any good glass cleaning fluid is recom-

mended, under no circumstances should alcohol or solvents be used!

The inside optical system should be maintained only by authorized persons. Please

contact your local dealer.

7.1 Safety Regulations

• Pull out the main plug!

• Wait min. 20 minutes after the last operation to cool down the fixture.

• Before you put the YYPPOOCC 557755 into operation close the casing, otherwise your

retina can be hurt!

7.2 Circumference and Interval (rule-of-thumb)

The contamination of the fixture depends on the environment details. Therefore

no general guidelines can be given. From this it follows that the intervals are only

suggestions from our practice experience.

Position Interval In this way

Outside optic weekly soft cloth and glass cleaning fluid

Color filter monthly soft cloth and glass cleaning fluid

Gobos yearly vacuum cleaner, airbrush, etc.

Glass gobos monthly soft cloth and glass cleaning fluid

Prism monthly soft cloth and glass cleaning fluid

Dimmer/Shutter yearly vacuum cleaner, airbrush, etc.

Inside lens monthly

Fan and air channel monthly vacuum cleaner, airbrush, etc.

Reflector

Lamp

never

never

soft cloth no glass cleaning fluid

Moveable parts yearly suitable fatty oil

GLP  German Light Production (V1.25) 24

Attention:

1. Never let optical parts come into contact with oil or fat.

2. Before running the fixture wait until all parts are dried up.

3. Never clean the aspheric lens with water or other cleaners. Change the
lens if it looks milky (about 1-2 years). For that please contact your local
dealer.

7.3 Cleaning the Optical System

1. Pull out the main plug!

2. Wait min. 20 minutes after the last operation to cool down the fixture.

3. Open the upper shell of the head casing by loosening the 4 Phillips screws.

Two on the front side and 2 on the back side of the head.

4. Do the work as explained in the list above.

5. Before you put the YYPPOOCC 557755 into operation close the casing, otherwise your

retina can be hurt!

GLP  German Light Production (V1.25) 25

8 Technical Specification

Power supply
Power consumption
EU-model
Fuse protection
US-model
Fuse protection

Lamp
Type 1

Optical system

Parabolic reflector
Doubles condenser lens
15° standard objective (optional 12° or 18°)
Lens anti-reflex

Color

11 dichroic filter plus white, 12 half-colors

Gobos

Gobowheel 1: 7 exchangeable rotating gobos plus "open", 4 glass Gobos
Gobowheel 2: 9 fixed exchangeable standard gobos plus "open"
Gobo outside diameter 27 mm, image size 23 mm
All gobos as steel or glass Gobos exchangeable, 9 spare Gobos

Shutter / Strobe / Dimmer

Strobe- effect with variable speed 1 - 10 flashes per second
Continuously mechanical dimmer 0 - 100%

Prism

Rotating 3-face prism, rotating and variable in speed

Focus

Motor driven focus from near to far away

Drive

Standard DMX-512, 3 pole XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
The DMX- addressing starts at the DMX- address [001].

Pan / Tilt
Pan- movement 530° in max. 2,65 seconds, 16 bit resolution
Tilt- movement 280° in max. 1,68 seconds, 16 bit resolution

Weights and measures
Width of the base 380 mm
Length of the base 315 mm (390 mm incl. handle)
height (head vertical) 510 mm
Weight (net) 24,4 kg
Weight (gross) 26,8 kg

700 Watt (blind current compensated)
AC 230V / 50 Hz~
T 5A, 250V, 5x20 mm (fine-wire fuse)
AC 115V / 60 Hz~
T 10A, 115V, 5x20 mm (fine-wire fuse)

HTI 575-DE (OSRAM)

GLP  German Light Production (V1.25) 26

9 Index

A

Adjustments ................................................... 16

aspheric lens .................................................... 25

Audio ................................................................ 11

B

BGV C1 .............................................................. 7

C

Calibrations ....................................................16

Change a Gobo................................................23

Circumference..................................................24

Clamps ............................................................... 7

Cleaning ........................................................... 25

Connected load .................................................. 9

D

Description of Device .........................................5

DIN VDE 0711-217 ............................................7

Display..............................................................15

DMX ...................................................................9

DMX- Address.................................................11

DMX Input ........................................................14

DMX Protocol ...................................................18

E

Error Messages ..............................................17

EU model ...........................................................9

F

Fan ...................................................................15

Feedback .........................................................17

Fixture Temperature ........................................15

Fuse ...................................................................9

G

Glass Gobos ....................................................23

I

Injury of the retina .............................................. 6

Invert ................................................................ 12

M

Maintenance ................................................... 24

Measures ......................................................... 26

Menu Field .......................................................10

Mounting ............................................................7

P

Pan- movement ............................................... 26

Power supply...................................................... 9

R

Reset................................................................ 12

Running time.................................................... 12

S

Safety Instructions ............................................. 6

Secure the YYPPOOCC 225500 ....................................... 8

Special Functions............................................. 13

T

Technical Specification .................................... 26

Test Program ................................................... 11

Tilt- movement .................................................26

U

US model ...........................................................9

V

VBG 70 .............................................................. 7

W

Weights ............................................................ 26

GLP  German Light Production (V1.25) 27

GLP  German Light Production (V1.25) 28