GLP Light Operator 48 User Manual

Download

Page 1

Please read before use

USER'S MANUAL

English

Light Operator 48

Page 2

Contents

Features 1

Technical Specifications 30

Brief of Main Functions 27

General Instructions 2

1. Overview 3

2. Operation Guide 7

3. MIDI Operation 23

1.1 Front View 3

2.1 Begin Programming 7

2.2 Editing 11

2.3 Running 18

3.1 Setting MIDI IN 23

3.2 Setting MIDI OUT 23

3.3 Exit MIDI Setting 24

3.4 Receiving MIDI File Dump 24

3.5 Sending MIDI File Dump 25

3.6 Implementation 25

2.2.1 Edit Enable 11

2.2.2 Erase a Program 12

2.2.3 Erase all Programs 13

2.2.4 Clear a Scene or Scenes 13

2.2.5 Delete a Step or Steps 14

2.2.6 Insert a Step or Steps 15

2.2.7 Modify a Step or Steps 17

2.3.1 Running Chase Programs 18

2.3.2 Running a Program To Audio 19

Speed Slider 20

Standard Beat 21

2.3.4 Running a Program With the

2.4 Change the Speed Mode between 5 Minutes and 10 Minutes 22

2.3.3 Running a Program With the

2.1.1 Record Enable 7

2.1.2 Security for Your Programs 7

2.1.3 Program Scenes 8

1.2 Rear View 6

Improvement and changes to

specifications, design and this

manual, may be made at any time

without prior notice.

Light Operator 48

Page 3

Features

Thank you for your purchase. This product features include:

Digital Technology Adopted.

Power Failure Memory.

Standard MIDI and DMX ports.

Powerful Program Edit.

Various Running Type.

More programs can run synchronously.

As a stage light controller, the unit can control intelligent unit and ordinary light.

Automatically recover to the last condition when you turn on the machine.

Conveniently connect with other units and machines.

You could edit different program according to your needs. The program could contain 4600 steps utmost and up to 96 programs could be stored.

You can run the SCENE with Audio, Speed Slider, Standard beat etc.

You can run more programs in Single Mode or Mix Mode simultaneously

Page 4

Read the instruction in this manual carefully and thoroughly, as they give important information regarding safety during use and maintenance. Keep this manual with the unit, in order to consult it in the future. If the unit is sold or given to another operator, make certain that it always has its manual, to enable the new owner to read aboutits operation and relative instructions.

This unit is intended for home use. After havingremoved thepackaging check that the unitis damaged in any way. If in doubt, use it and contact an authorized dealer. Packaging material (plastic bags, polystyrene foam, nails, etc.) be left within children's reach, as it can be dangerous. This unit must only be operated by adults. allow children to tamper or play with it.

use the unit under the following conditions: In places subject to excessive humidity. In places subject to vibrations or bumps. In places with a temperature of over 45 C or less than 2 C/35.6 F.

Protect the unit from excessive dryness or humidity (ideal conditions are between 35% and 80%).

dismantle or modify the unit.

NOT

DON'T

MUST NOT

DO NOT

NEVER

DO NOT

DISCONNECT

STOP

DO NOT NEVER

make any inflammable liquids, water or metal objects enter the unit. Should any liquid be spilled on the unit, the power supply to the unit immediately.

using the unit immediately In the event of serious operation problems and

either contact your local dealer for a check or contact us directly.

open the unit--there are no user serviceable parts inside.

try to repair the unit yourself. Repairs by unqualified people could cause

damage or faulty operation. Contact your nearest dealer.

/113 F

General Instructions

Warnings

Cautions

Page 5

1. Overview

1.1 Front View

10 11

13 14 15

24 25

26 27 28 29 30

Page 6

1. Overview

1. Preset A LEDs

4. Preset B LEDs

5. SCENE LEDs

2. Channel Sliders 1-24

6. Channel Sliders 25-48

3. Flash Buttons 1-24

7. Flash Buttons 25-48

8. Dark Button

9. Down/Beat Rev

10. Mode Select/Rec Speed

11. Up/Chase Rev

12. Page Button

13. Delete/ Rev One

14. Segment Display

15. Insert/%or0-255

from 1 to 24.

to full intensity.

These 24 buttons are used to bring an individual channel,

to full intensity. They also are used for programming.

This button is used to momentarily black out overall output.

program with regular beat.

in Mix mode.

under Speed Slider control.

Tap to select pages of scenes from Page 1-4.

of any program.

Shows the current activity or programming state.

Insert is to add one step or steps into a scene. % or 0-255 is used to change display value cycle between % and 0-255.

Delete any step of a scene or reverse the chasing direction

Chase Rev is to reverse the chasing direction of a scene

Up is used to modify a scene in Edit mode.

Rec Speed: Set the speed of any of the programs chasing

CHNS /SCENES, Double Preset and Single Preset.

Each tap will activate the operating mode in the order:

BEAT REV is used to reverse the chasing direction of a

DOWN functions to modify a scene in Edit mode;

These 24 buttons are used to bring an individual channel,

intensities of channels 1-24.

These 24 sliders are used to control and /or program the

intensities of channels 25-48.

These 24 sliders are used to control and /or program the

Show the current intensity of the relevant channel numbered

from 25-48.

Light when relevant scenes are active.

Show the current intensity of the relevant channel numbered

1.1 Front View

Page 7

1. Overview

16. Edit / All Rev

17. Add or Kill/ Rec Exit

18. Record/ Shift

19. Master A Button

20. Park Button

21. Hold Button

22. Step Button

23. Audio Button

24. Master Slider A

25. Master Slider B

26. Blind Button

27. Home Button

28. Tap Sync Button

29. Full On Button

30. Black Out Button

31. Fade Time Slider

32. Speed Slider

33. Audio Level Slider

34. Fog Machine button

All Rev is to reverse the chasing direction of all programs.

Rec Exit is used to exit from Program or Edit mode.

Shift functions only used with other buttons.

Brings channel 1-12 to full of current setting.

Master B slider, depending on the current mode.

This button is used to maintain current scene.

is pushed to the bottom or in Edit mode.

Activates audio sync of chase and audio intensity effects.

This slider controls overall output of all channels.

This slider controls the chase of all programs.

in CHNS /SCENE mode.

This button is used to deactivate the Blind.

Repeatedly tapping this button establish the chase speed.

This function bring overall output to full intensity.

resulting from Flash and Full On.

Used to adjust the Fade Time.

Used to adjust the chase speed.

This slider controls the sensitivity of the Audio input.

This button is used to kill all output with exception for that

This function takes the channel out of the chase of a program

This button is used to go to next step when the Speed Slider

full of current setting, or momentarily program a scene into

Used to select Single/Mix Chase, bring Channel 13-24 to

Record is used to activate Record mode or program a step.

scenes or programs.

In Kill mode, pressing any Flash button will kill any other

at a time.

In Add mode, multiple scenes or Flash buttons will be on

Edit is used to activate Edit mode.

1.1 Front View

Page 8

1. Overview

35. Power Switch

36. DC Input

37. MIDI Thru/Out/In

38. DMX Out

39. DMX Polarity Select

40. Audio Input

41. Remote Input

42. Fog Machine Connector

This switch controls turning on or off of the power.

DC 12-20V, 500 mA Min.

MIDI ports for connection to a sequencer or MIDI device.

or DMX pack.

Used to select DMX polarity.

from 100mV to 1Vpp.

control using a standard 1/4"stereo jack.

Black Out and Full On may be controlled by a remote

This jack accepts a line level audio input signal ranged

This connector sends your DMX value to the DMX fixture

1.2 Rear View

DC INPUT

DC 12V~20V

500mA min.

100mV~1Vp-p

AUDIO

LINE INPUT

1/4"stereo jack

Full on

GND

REMOTE

INOUTTHRU

MIDI DMX OUT

DMX Polarity Select

1=Ground 2=Data 3=Data +

1=Ground 2=Data + 3=Data

ON OFF

POWER FOG MACHINE

Stand By

or Black Out

35 36 40 424137 38 39

Page 9

2. Operation Guide

2.1 Begin Programming

2.1.1 Record Enable

2.1.2 Security for Your Programs

RECORD

1. Press and hold down the Record button.

2. While holding down the Record button, tap the Flash buttons 1, 6, 6 and 8 in sequence.

3. Release the Record button, the Record LED lights up, now you can begin programming your chase patterns.

To protect your programs from any editing by others, you may change the Record Code.

1668

NOTE:

The first time you turn on your unit, the default setting of the Record Code is Flash buttons 1, 6, 6 and 8.

You may change the Record Code to protect your programs.

1. Enter current Record Code(Flash buttons 1, 6, 6 and 8).

2. Press and hold down the Record and Edit buttons at a time.

Page 10

2. Operation Guide

2.1.2 Security for Your Programs

2.1.3 Program Scenes

SELECT

MODE

CHNS

DOUBLE

1-24 SINGLE

PRESET

SCENES

3. While holding the Record and Edit buttons, tap the desired Flash button to enter a new Record Code The Record Code consists of 4 Flash buttons(the same button or different buttons), be sure your new Record Code consists of 4 Flash buttons.

4. Enter your new Record Code a second time, all channel LEDs and scene LEDs will flash three times, now the Record Code is changed.

5. Exit Record mode. Tap the Rec Exit button while pressing and holding down the Record button, release the two buttons at a time, the Record mode is disengaged.

IMPORTANT!!!

Always remember to exit Record mode when you won't continue your programming, otherwise you may lose control of your unit.

NOTE:

The second time you enter your new Record Code different from that of the first time, the LEDs will not flash, which means you've failed to change the Record Code.

When you've entered a new Record Code the first time, and now you want to cancel the new Record Code, you may press and hold down the Record and Exit buttons at a time to exit.

1. Record Enable.

2. Select the 1-48 Single mode by tapping the the Mode Select button. This will give you control of all 48 channels as you program.

Be sure that MasterA&Bareboth set at maximum. (Master A is at its maximum in the fully up position , while Master B is at its maximum in the fully down position.)

Page 11

2.1.3 Program Scenes

2. Operation Guide

3. Create a desired scene using Channel Sliders 1-48. At 0% or DMX 0, these sliders should be at 0 position, and at 100% or DMX 255, these sliders should be at 10 position.

RECORD

PAGE

4. Once the scene is satisfactory, tap the Record button to program the scene as a step into the memory.

5. Repeat step 3 and step 4 until all desired steps have been programmed into memory. You may program up to 1000 steps into memory.

6. Select a chase bank or scene master to store your program. Tap the Page button to select a page(Page 1-4) to store your scenes.

1234

Page 12

2.1.3 Program Scenes

2. Operation Guide

RECORD

REC EXIT

FLASH 25-48

7. Press a Flash button between 25-48 while

holding down the Record button. All LED will flash indicating the scenes have been programmed into memory.

8. You can continue programming or exit.

To exit Program mode, tap the Exit button while holding down the Record button, the Record LED should go out.

EXAMPLE: Program a 16 steps chase with channel 1-32 at full in sequence into Flash button 25 of Page 1.

1. Record enable.

2. Push MasterA&Btomaximum position and Fade slider to top.

3. Tap the Mode Select button to select 1-48 Single mode.

4. Push Channel slider 1 to the top position, its LED light at full intensity.

5. Tap the Record button to program this step into memory.

6. Repeat steps 4 and 5 until you've programmed Channel sliders 1-32.

7. Tap the Page button causing Page 1 LED lights.

8. Tap the Flash button 25 while holding down the Record button, all LEDs will flash indicating you've programmed the chase into memory.

Page 13

SELECT

MODE

CHNS

DOUBLE

1-24 SINGLE

PRESET

SCENES

2.2 Editing

2.2.1 Edit Enable

2. Operation Guide

1. Record enable.

2. Use the Page button to select the page the program you wish to edit is on.

4. Press and hold down the Edit button.

3. Tap the Mode Select button to select CHNS SCENES.

PAGE

EDIT

1234

Page 14

2.2.1 Edit Programs

2.2.2 Erase a Program

2. Operation Guide

2. Use the Page button to select the page the program you wish to erase is on.

5. While holding down the Edit button, tap the Flash button that corresponds to the program you wish to edit.

3. While holding down the Edit button, tap the Flash button(25-48) .twice

4. Release the two buttons ,all LEDs flash, indicating the program is erased.

6. Release the Edit button, the relevant scene LED should light indicating you are in the Edit mode.

PAGE

12 34

EDIT

FLASH 25-48

1. Record enable.

Tap this button twice

Page 15

2. Operation Guide

2.2 Editing

2.2.3 Erase All Programs

2.2.4 Clear a Scene or Scenes

1. Press and hold the Record button.

2. Tap the Flash buttons 1, 4, 2 and 3 in sequence while holding the Record button. All LEDs will flash, indicating all programs stored in memory have been erased.

RECORD

1423

1. Record enable.

2. Record a scene or scenes.

3. If you are not satisfied with the scene or scenes, you may tap the Rec Clear button while pressing and holding the Record button, all LEDs will flash, indicating the scenes have been cleared.

RECORD

REC

CLEAR

Page 16

2. Operation Guide

STEP

DELETE

RECORD

REC

EXIT

2.2 Editing

2.2.5 Delete a Step or Steps

1. Enter the Edit mode.

2. Tap the Step button to scroll to the step you wish to delete.

3. Tap the Delete button when you reach to the

step you wish to delete, all LEDs will flash briefly indicating the deletion of the step.

4. Continue steps 2 and 3 until all the unwanted

steps have been deleted.

5. Tap the Rec Exit button while pressing and

holding down the Record button, the Scene LED goes out, indicating the exit of Edit mode.

Page 17

2. Operation Guide

2.2 Editing

2.2.5 Delete a Step or Steps

2.2.6 Insert a Step or Steps

EXAMPLE: Delete the third step of the program on Flash button 25 on Page 2.

1. Record enable.

2. Tap the Mode Select button to select CHNS SCENE mode.

3. Tap the Page button until Page 2 LED lights.

4. Tap the Flash button 25 while pressing and holding down the Edit button, the Scene LED lights.

5. Tap the Step button to scroll to the third step.

6. Tap the Delete button to delete the step.

7. Tap the Rec Exit button while pressing and holding down the Record button to exit Edit mode.

1. Record a scene or scenes you wish to insert.

2. Be sure you're in CHNS SCENE and Enter the Edit mode.

3. Tap the Step button to scroll to the step which you wish to insert before. You may read the step from the Segment Display.

STEP

Page 18

2. Operation Guide

2.2.6 Insert a Step or Steps

EXAMPLE: Insert a step with channels 1-12 fully on at a time between step 4 and step 5 of program 35.

INSERT

4. Tap the Insert button to insert the step you've created before, all LEDs will flash, indicating the step is inserted.

5. Exit Edit mode.

1. Record enable.

2. Push Channel sliders 1-12 to the top and record the scene as a step.

3. Tap the Mode Select button to select CHNS SCENE mode.

4. Tap the Page button until Page 2 LED lights.

5. Tap the Flash button 35 while holding down the Edit button, the corresponding scene LED lights.

6. Tap the Step button to scroll to the step 4.

7. Tap the Insert button to insert the scene you've created before .

Page 19

2. Operation Guide

2.2 Editing

2.2.7 Modify a Step or Steps

1. Enter Edit mode.

2. Tap the Step button to scroll to the step you wish to modify.

3. Press and hold the Up button if you want to raise the intensity. If you want to lower the intensity, press and hold down the Down button.

5. Repeat steps 2, 3 and 4 until all the steps have been modified.

6. Exit Edit mode.

4. While holding down the Up or Down button, tap the Flash button corresponding to the DMX channel of the scene you wish to modify until you reach the desired intensity value read from the Segment Display. Then you may tap the Flash buttons until you are satisfied with the new scene.

STEP

Page 20

2. Operation Guide

2.3.1 Running Chase Programs

2.3 Running

1. Tap the Mode Select button to select CHNS SCENE mode indicated by the red LED.

2. Tap the Page button to select the correct page the program you wish to run is located.

3. Push Master Slider B to its maximum position(fully down).

SELECT

MODE

CHNS

DOUBLE

1-24 SINGLE

PRESET

SCENES

PAGE

12 34

MASTER

010

Page 21

2. Operation Guide

2.3.1 Running Chase Programs

2.3.2 Running a Program To Audio

4. Move the desired Channel slider (25-48) to its maximum position to trigger the program, and the program will fade in depending upon current fade time. You may press and hold down the relevant Flash button(25-48) to trigger the program.

5. Move the Channel slider to adjust the output of the current program.

1. Use built-in microphone or plug the audio source into the RCA Audio jack.

2. Select your program as described above.

3. Tap the Audio button until its LED lights, indicating Audio mode is active.

AUDIO

Page 22

2. Operation Guide

2.3.2 Running a Program To Audio

2.3.3 Running a Program With the Speed Slider

AUDIO

AUDIO LEVEL

4. Use the Audio Level slider to adjust the music sensitivity.

5. To return to normal mode, tap the Audio button

a second time causing its LED goes out, the Audio mode is disengaged.

1. Be sure the Audio mode is disengaged, that is, the Audio LED goes out.

2. Select your program as described above.

3. Move the Speed slider to the SHOW MODE position(the bottom), then tap the Flash button (25-48) while pressing and holding down the Rec Speed button, the corresponding program will not run with the Standard beat any longer.

REC SPEED

FLASH 13-24

Page 23

.2s

.5s 1s

1s 2s

2s 5s 5s 10s

10s 20s

30s 1m

1m 2m 2m 5m

5m 10m

.1SEC .1SEC

5MIN 10MIN

MINS MINS

SHOW SHOW

MODE MODE

SPEED

2. Operation Guide

2.3.3 Running a Program With the Speed Slider

2.3.4 Running a Program With the Standard Beat

2. Tap the Park button to select Mix Chase mode, the LED lights indicating this selection.

4. Now you may move the Speed Slider to select your desired speed.

3. Select your program as described above.

4. Move the Speed slider until the Segment Display reads your desired value.

You may tap the Tap Sync button twice to define your beat time.

1. Be sure the Audio is disengaged. Tap the Mode Select button to select CHNS SCENE mode.

PARK

SINGLE CHASE

MIX CHASE

.2s

.5s 1s 1s 2s

2s 5s 5s 10s

10s 20s

30s 1m

1m 2m 2m 5m 5m 10m

.1SEC .1SEC

5MIN 10MIN

MINS MINS SHOW SHOW MODE MODE

SPEED

NOTE:

The step 3 is not necessary if the selected program is not recorded with the Standard Beat.

Page 24

2. Operation Guide

2.3.4 Running a Program With the Standard Beat

2.4 Change the Speed Mode between 5 Minutes and 10 Minutes

5. While pressing and holding down the Rec Speed button, tap the Flash button(25-48) that stores the program.

6. The program will then run with the set time or beat when engaged.

7. Repeat steps 4 and 5 to set a new beat time.

REC SPEED

FLASH BUTTONS 25-48

RECORD

Flash Button 5 or 10

RECORD

1. Press and hold the Record button.

2. Tap the Flash button 5 or 10 three times while holding down the Record button.

3. The 5MIN or 10MIN should light up indicating the Speed slider is set to run in the 5 or 10 minute mode.

Tap this button three times

Page 25

3. MIDI Operation

3.1 Setting MIDI IN

3.2 Setting MIDI OUT

RECORD

Flash button 1

Flash button 2

Flash buttons 1-16

1. Tap the Flash button 1 three times while holding down the Record button, the Segment Display reads "CHI" indicating MIDI IN channel setup is available.

1. Tap the Flash button 2 three times while holding down the Record button, the Segment Display reads "CHO" indicating MIDI OUT channel setup is available.

2. Tap the Flash button numbered from 1-16 to assign MIDI IN channel 1-16, the relevant channel LED lights indicating MIDI IN channel is set.

Tap this button three times

Page 26

3. MIDI Operation

3.2 Setting MIDI OUT

3.3 Exit MIDI Setting

3.4 Receiving MIDI File Dump

RECORD

Flash button 3

Flash buttons 1-16

Tap the Flash button 3 three times while holding down the Record button, the Segment Display reads "IN" indicating the controller is ready to receive MIDI file dump.

2. Tap the Flash button numbered from 1-16 to assign MIDI OUT channel 1-16, the relevant channel LED lights indicating MIDI OUT channel is set.

RECORD

REC

EXIT

Press and hold down the Record button. While holding down the Record button tap the Rec Exit button to exit MIDI setting.

Tap this button three times

Page 27

3. MIDI Operation

3.5 Sending MIDI File Dump

3.6 Implementation

RECORD

Flash button 4

Tap the Flash button 4 three times while holding down the Record button, the Segment Display reads "OUT" indicating the controller is ready to send a file.

Tap this button three times

NOTE:

1. During file dump, all other operations will not function. Functions will automatically return when the file dump is completed.

2. File dump will be interrupted and stop if errors occur or power failure.

1. During receiving and sending MIDI data, all MIDI scenes and channels being run

will automatically paused if there is no response within 10 minutes.

2.During receiving and sending file dump, the controller will automatically search for

or send Device ID of 55H(85), a file named DC2448 with an extension of "BIN(SPACE)".

3.File dump allows this controller to send its MIDI data to next unit or other

MIDI devices.

Page 28

3. MIDI Operation

3.6 Implementation

4. There are two types of file dump mode described as below:

5. The controller will send and receive Note On and Note Off data via the Flash buttons.

Functions

Velocity

Note NO.

turn on or off program 1-48Program master

22-69

Activate Channel 1-48Channel intensity

70--93

FULL -ON

DARK

HOLD

Turn on or off AUDIO

CHNS SCENES

DOUBLE PRESET Mode

SINGLE PRESET Mode

100

Step

101

BLACK OUT

102

CONTROLLER RECEIVER

MIDI OUT MIDI IN MIDI OUT MIDI IN

CONTROLLER RECEIVER

MIDI OUT MIDI IN MIDI OUT MIDI IN

Close Loop Mode

Open Loop Mode

Page 29

4. Brief of Main Functions

1. The Tap Sync button is used to set and synchronize the chase rate (the rate at which all scenes will sequence) by taping the button several times. The chase rate will synchronize to the time of the last two taps. The LED above the Step Button will flash at the new chase rate. The chase rate may be set anytime whether or not a program is running.

2. Tap Sync will override any previous setting of the speed slider control until the slider is

moved again.

3. Use of Tap Sync in setting a standard beat is the same with speed control slider.

Tap Sync Button:

1. Reverse the direction of all the scenes:

Press the ALL REV Button, all the scenes should change their directions.

2. Reverse the chasing direction of all the programs with speed control.

Press the Chase Rev Button.

3. Reverse the chasing direction of all the programs with standard beat:

Press the Beat Rev Button.

4. Revers chasing direction of any program:

Press and hold down the Rec One Button, then press down the Flash Button corresponding to your desired program and release together.

Reverse the direction of the scene

1. The amount of time it will take for the dimmer to go from zero output to maximum

output, a nd vice verse.

2. Fade time is adjusted through the Fade Time Slider, which varies from instant to

10 minutes.

Fade Time

Master Slider control provides proportional level control over all channels and scenes with the exception of the Flash Buttons. For example: Whenever the Master slider control is at minimum all stage outputs will be at zero except for any resulting from a Flash Button or FULL ON Button. If the Master is at 50%, all outputs will be at only 50% of the setting of current channel or scenes except for any resulting from a Flash Button or FULL ON Button.

If the Master is at full all outputs will follow the unit setting.

Master A always controls outputs of channels. Master B controls the program or a scene except in Double Preset Mode.

Master Slider

Page 30

1. Will run all programs synchronously.

2. All programs can be controlled by the same SLIDER SPEED, or each programs speed may be controlled individually. (See Speed Setting ).

3. Press the MODE SELECT BUTTON and select "CHNS SCENES".

4. Press the PARK BUTTON to select MIX CHASE MODE. A yellow LED will indicate this selection.

4. Brief of Main Functions

1. The 3-Digit Display is used to display intensity percentage or absolute

DMX value.

2. To change between percentage and absolute value:

Press and hold the Shift Button. While holding down the Shift button press the

% or 0-255 Button to switch between percentage and absolute values.

3. If the Display reads, for example, "076", it means a percentage value 76%.

If the Display reads "076.", it means the DMX value 76.

Segment

Dimmer Display

Mix Mode

Blind and Home

1. Blind function takes channels temporally out from a chase, when the chase is running,

and gives you manual control over the channel.

2. Press and hold the Blind Button and tap the relative Flash Button you want to temporarily

take out of the chase.

3. To return to normal chase again press and hold the Home Button and push the Flash

Button you want to return to normal chase.

1. All programs will run in sequential order starting in the order of program number.

2. The Display will read the running program number.

3. All programs will be controlled by the same Speed Slider .

4. Press the MODE SELECT BUTTON and select " CHNS SCENES".

5. Press the PARK BUTTON to select SINGLE CHASE MODE. A red LED will indicate this selection.

Segment

Single Mode

Page 31

4. Brief of Main Functions

The ADD/KILL Button changes the mode of the flash buttons. Normally the flash buttons are in Add mode, whereas pressing any flash button will not kill other scenes, allowing multiple scenes to be on at a time. The Kill mode is activated by pressing the Add/Kill button and illuminating the LED above it. Pressing any flash button will kill other active SCENE or Program.

In Kill Mode, the killed program does not stop running but can not output.

Add and Kill

1. In CHNS SCENES Mode, press down the button you can change the chasing mode of programs between Single Mode and Mix Mode.

2.In Double Preset Mode, pressing down this button is equal to pushing Master Slider B

to the top.

3.In Single Preset Mode, this button could temporally record current output, with

Master Slider B to adjust.

Park

1. Enter the Double Preset Mode.

2. Push Channel Sliders 1 to 6 to the top and move Channel Sliders 19 to 24 to the maximum.

3. Move Master A and B to the same level and push them to the same direction, you will get a scene.

Example

1. Press Mode Select Button to enter A Double Preset Mode.

2. In this mode, Channel Sliders 1-24 and channel sliders 25-48 both control Channel 1-24.

3. Master A controls channel Slider 1-24 while Master B controls Channel Sliders 25-48.

4. In this Mode, no scene could be recorded.

Double Preset

Page 32

Technical Specifications

Power Input .............................................. DC 12~20V, 500 mA min.

DMX Output .......................................................... 3 pin female XLR

MIDI Signal ................................................. 5 pin standard interface

Audio Input ................................................................ 100 mV~1Vpp

Fuse(internal) .................................................. F0.5A 250V 5x20mm

Dimensions .............................................................. 711x264x85mm

Weight(appro.) ........................................................................ 7.2 kg

Attention!

1. To retain your programs from loss, this unit must be powered not less than two hour every month.

2. The Segment Display shows "LOP" if the voltage is too low.

GLP Light Operator 48 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual