GLP Ipression XL Instruction Manual
Instruction Manual
from Software Version 1.09/0.3
(Manual Version 1.06)
e-mail: service@glp.de
Internet: http://www.glp.de
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.06) / from Software Version 1.09/0.3)
2
For your notes:
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.06) / from Software Version 1.09/0.3)
3
Table of content
1 Description of Device ........................................................................................................ 4
1.1 Safety Instructions .......................................................................................................................5
2 Preparation and Installation.............................................................................................. 6
2.1 Mounting ......................................................................................................................................6
2.1.1
Mounting on the floor (upright) ....................................................................................7
2.1.2
Mounting in hanging position (Head down) .................................................................7
2.1.3
Mounting in sideway position .......................................................................................8
2.2 Securing the Device ....................................................................................................................9
2.3 Connections .................................................................................................................................9
2.3.1
Power Supply ...............................................................................................................9
2.3.2
DMX .............................................................................................................................9
3 The Menu Field ................................................................................................................ 10
4 DMX Channel Sheet ......................................................................................................... 12
5
5 Maintaining and Cleaning the IIMMPPRREESSSSIIOONN XXLL ............................................................ 17
5.1 Safety regulations ..................................................................................................................... 17
5.2 Maintenance Intervals (rule-of-thumb) ..................................................................................... 17
6 Technical Specifications ................................................................................................. 18
7 Index ................................................................................................................................. 20
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.06) / from Software Version 1.09/0.3)
4
1 Description of Device
1. Moving head (actively and
passively cooled)
2. Arm with various cooling
vents
3. Tilt-lock to secure and lock
the tilt movement see also
1.1
4. LCD-Display/Menu (data
entry)
5. Base with various connectors
and Camlock mounting
system
Safety eyelets
1
2
4
5
3
base side 1
10
678910
base side 2
11
12
13
14
6. DMX- Output (5 Pin)
7. DMX- Output (3 Pin)
8. Micro-fuse 6.3x32mm, T15A
9. Power On/Off
10. 2x Safety eyelets
11. Powercon (Mains supply)
12. Blank panel
13. DMX- Input (3 Pin)
14. DMX- Input (5 in)
Note: Only connect one cable to the
DMX-Out/Input at a time!
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.06) / from Software Version 1.09/0.3)
5
1.1 Safety Instructions
The IIMMPPRREESSSSIIOONN XXLL is an advanced technology product. To guarantee
smooth operation, it is necessary to follow the following instructions.
The manufacturer of this device will not take responsibility of damages
through any disregard of the information in this user manual. Warranty claims
will also be cancelled in the event of the system casing being opened.
1. Make sure that before powering up the fixture, the fans and air inlets are
clean and not blocked by anything.
2. Before powering up the fixture, ensure that the moving head part of the
fixture can rotate unhindered through its full range of movement.
3. A safety distance of at least 0.5 m to any easily flammable material (e.g.
decoration material) must be adhered to.
4. Attention! Don’t touch the device during operation. Parts of the fixture can
become hot and can cause injuries and / or damages.
5. The system doesn’t contain any user serviceable parts. Opening the fixture
will void the manufacturers warranty.
6. Danger of burning. Wait at least 15 minutes after disconnecting the AC
power before changing the optical carrier on the fixture. Pay attention to
possible hot parts of the system.
7. Never look directly into the beam of light or one of the LEDs. Never use
optical apertures with a distance less than 0.5 m to observe the beam of
light. LED Class 2M. Not following these precautions can result in serious
injury to your eyes and in particular, your retina.
Attention:
LED Class 2M can cause injuries of your eyes even
without optical instruments in front of them or within a distance
of less than 0.5m and short exposure time.
Avoid direct radiation to your eyes!
8. To ensure proper operation, you must also follow the installation guide
described in chapter 2 of this manual. Operating the IIMMPPRREESSSSIIOONN XXLL
without suitable mounting devices can increase the risk of an accident.
9. The IIMMPPRREESSSSIIOONN XXLL features a unique small and lightweight design with
no specific carrying handles. Care needs to be shown when handling the
fixture to ensure that no unnecessary damage should occur. Fragile areas
include the LCD display and cover on one side arm and the front bezel.
Pressure in these areas could result in damages which will not be covered
by the standard warranty.
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.06) / from Software Version 1.09/0.3)
6
10. Repair-, maintenance- and installation work should only be performed by
qualified or GLP certified staff. You need to pay attention to the common
rules of technology that are not explicit mentioned in this manual.
11. Use only original spare parts. Any structural modification on the system will
terminate all warranty claims.
12. Please keep this instruction manual for future reference.
2 Preparation and Installation
2.1 Mounting
The IIMMPPRREESSSSIIOONN XXLL is fully operational whether it hangs or is mounted to a
wall. It can also be operated while standing on the floor. Keep a safety distance
of 0.5 m from any easily inflammable materials (decoration etc.).
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217.
The installation shall be done by qualified personal only.
For the various mounting positions of the IIMMPPRREESSSSIIOONN XXLL (standing on the
floor, sideways or hanging) different accessories kits are available. Using any
required kits, along with the standard mounting connectors on the base of the
fixture, will ensure a safe and firm installation.
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.06) / from Software Version 1.09/0.3)
7
2.1.1 Mounting on the floor (upright)
To operate the IIMMPPRREESSSSIIOONN XL in an upright position, please use the
dedicated floor-stand which ships with all original fixtures. The floor
stand is mounted to the base of the fixture using the two Camlock
quarter turn fasteners. Line up and engage the camlock connectors from
the floor stand into the base of the fixture and turn the two fasteners 90°
to lock them. Do the opposite to release them again. On both sides you'll
find eyelets to pull though a fixing strap. This allows additional bracing of
the floor-stand during the upright operation.
2.1.2 Mounting in hanging position (Head down)
To operate the IIMMPPRREESSSSIIOONN XL in a hanging position, two omega
brackets can be mounted directly to the bottom of the base using the
four Camlock connectors.
Loading...