GLP impression XL Instruction Manual
Instruction Manual
from Software Version 1.09/0.3
(Manual Version 1.04)
e-mail: service@glp.de
Internet: http://www.glp.de
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.04) / from Software Version 1.09/0.3)
2
For your notes:
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.04) / from Software Version 1.09/0.3)
3
Table of content
1 Description of Device ........................................................................................................ 4
1.1 Safety Instructions .......................................................................................................................5
2 Preparation and Installation.............................................................................................. 6
2.1 Mounting ......................................................................................................................................6
2.1.1 Mounting on the Floor (Upright) ......................................................................................7
2.1.2 Mounting in hanging Position (Head first) .......................................................................7
2.1.3 Mounting in sidewise Position .........................................................................................8
2.2 Secure the Device .......................................................................................................................9
2.3 Connections .................................................................................................................................9
2.3.1 Power Supply ..................................................................................................................9
2.3.2 DMX ................................................................................................................................9
3 The Menu Field ................................................................................................................ 10
4 DMX Channel Sheet ......................................................................................................... 12
5 Maintaining and Cleaning the IIMMPPRREESSSSIIOONN XXLL ............................................................ 17
5.1 Safety regulations ..................................................................................................................... 17
5.2 Circumference and Interval (rule-of-thumb) ............................................................................. 17
6 Technical Specifications ................................................................................................. 18
7 Index ................................................................................................................................. 19
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.04) / from Software Version 1.09/0.3)
4
1 Description of Device
1. Moving head (actively and
passively cooled)
2. Arm with various cooling
vents
3. Tilt-lock to secure and lock
the tilt movement see also
1.1 Safety Instructions
4. LCD-Display/Menu (data
entry)
5. Base with various connectors
and Camlock mounting
system
Safety eyelets
1
2
4
5
3
base side 1
10
678910
base side 2
11
12
13
14
6. DMX- Output (5 Pin)
7. DMX- Output (3 Pin)
8. Micro-fuse 6.3x32mm, T15A
9. Power On/Off
10. 2x Safety eyelets
11. Powercon (Mains supply)
12. Blank panel
13. DMX- Input (3 Pin)
14. DMX- Input (5 in)
Note: Only connect one cable to the
DMX-Out/Input at a time!
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.04) / from Software Version 1.09/0.3)
5
1.1 Safety Instructions
The IIMMPPRREESSSSIIOONN XXLL is a High-Tech Product. To guarantee a
smooth operation, it is necessary to respect the following rules.
The manufacturer of this device will not take responsibility of
damages through any disregard of the information in this
manual. Warranty claims also will be cancelled in case the
system casing is opened.
1. Make sure before putting the system into operation, that the fan and the air
inlets are clean and not blocked by anything.
2. It must be assured that the system-head can rotate unhindered throughout
his complete rotating range. A safety distance of at least 0.5 m to any easily
inflammable material (e.g. decoration material) must be adhered.
3. Attention! Don’t touch the device during the operation. This can cause
injuries or damages.
4. Only connect one cable to the DMX-Out/Input at a time!
5. Attention! The Tilt-Lock shall only be used to secure the head of the unit
during transport – or during repair of the fixture. Never lift or carry the fixture
by holding its head when the Tilt-Lock is in position. Otherwise the Tilt-Lock
may become dysfunctional.
6. The system doesn’t contain any maintainable parts. Don’t open it!
7. It is necessary to wait at least 15 minutes after disconnecting the AC before
changing the optical carrier. Pay attention to possibly hot parts of the
system.
-- Danger of BURNING --
8. Never look directly into the beam of light or one of the LEDs. Never use
optical apertures with a distance less than 0.5 m to observe the beam of
light. LED Class 2M. You'll risk a serious injury of your eyes and in
particular of your retina.
Attention:
LED Class 2M can cause injuries of your eyes even
without optical instruments in front of them or within a distance
of less than 0.5m and short exposure time.
Hence: Avoid direct radiation of your eyes!
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Manual Version 1.04) / from Software Version 1.09/0.3)
6
9. To allow a secure operation, follow also the Installation guide described in
chapter 2. Operating the IIMMPPRREESSSSIIOONN XXLL without suitable safety aids like
Safety cables or clamps/hooks can increase the risk of an accident.
10. Repair-, maintenance- and installation work shall be done by qualified or
GLP certified staff only. You need to pay attention to the common rules of
technology that are not explicit mentioned in this manual.
11. Use only original spare parts. Any structural modification on the system will
terminate all warranty claims.
12. Please keep this instruction manual for later reference.
2 Preparation and Installation
2.1 Mounting
The IIMMPPRREESSSSIIOONN XXLL is fully operational whether it hangs or is mounted to the
wall. It can also be operated while standing on the floor. Keep a safety distance
of 0.5 m towards any easily inflammable materials (decoration etc.).
Loading...