GLP impression spot one Instruction Manual
Instruction Manual
from software version 1.52
(Instruction version 1.93)
e-mail: service@glp.de
Internet: http://www.glp.de
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
2
Notes:
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
3
Table of contents
1 Description of Device.............................................................................................. 4
1.1 Safety Instructions ............................................................................................ 5
2 Preparation and Installation ................................................................................... 6
2.1 Mounting ........................................................................................................... 6
2.1.1 Mounting on the floor (upright) ............................................................. 7
2.1.1 Mounting in hanging position (Head down) .......................................... 7
2.1.2 Mounting in sideways position ............................................................. 8
2.2 Securing the device .......................................................................................... 8
2.3 Connections ...................................................................................................... 9
2.3.1 Power Supply....................................................................................... 9
2.3.2 DMX ..................................................................................................... 9
3 The Menu Field ........................................................................................................ 9
4
4 Changing Gobos and the Effect wheel ................................................................ 21
4.1 Changing Gobos and the Effect wheel ........................................................... 21
4.1.1 General remarks for changing gobos ................................................. 21
4.1.2 Changing rotating gobos .................................................................... 22
4.1.3 Changing the effect wheel ................................................................. 25
5
5 Colored Error Code ............................................................................................... 27
6
6 Maintaining and Cleaning the IImmpprreessssiioonn SSppoott oonnee .......................................... 27
6.1 Safety regulations ........................................................................................... 27
6.2 Maintenance Intervals (rule-of-thumb) ............................................................ 28
7 Technical Specifications ...................................................................................... 29
8 Index ....................................................................................................................... 30
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
4
1 Description of Device
1. Moving Head
2. Arm with various cooling vents
3. Tilt-lock to secure and lock the
tilt movement
4. Backlight LCD graphical menu
(data entry)
5. Base with various connectors
and Camlock mounting
system
6. DMX- Output (5 Pin)
7. DMX- Output (3 Pin)
8. Micro-fuse 6.3x32mm, T8A
9. Power Switch
10. 2x Safety wire points
11. Neutrik Powercon (Mains power
input)
12. Blank panel (primed for Ethernet)
13. DMX- Input (3 Pin)
14. DMX- Input (5 Pin)
Note: Only connect one cable to the
DMX Input / Output at the same time!
Base Side 1
10 6 7 8 9 10
Base Side 2
11 12 13 14
1
2
3
4
5
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
5
1.1 Safety Instructions
The IImmpprreessssiioonn SSppoott oonnee
is an advanced technology product.
To guarantee smooth operation, it is necessary to follow the
following instructions.
The manufacturer of this device will not take responsibility of
damages through any disregard of the information in this user
manual. Warranty claims will also be cancelled in the event of
the system casing being opened.
1. Make sure that before powering up the fixture, the fans and air inlets are
clean and not blocked by anything.
2. Before powering up the fixture, ensure that the moving head part of the
fixture can rotate unhindered through its full range of movement.
3. A safety distance of at least 0.5 m to any easily flammable material (e.g.
decoration material) must be adhered to.
4. Attention! Don’t touch the device during operation. Parts of the fixture can
become hot and can cause injuries and / or damages.
5. Use only one DMX Input / Output at the same time.
6. Never look directly into the beam of light or one of the LEDs. Never use
optical apertures with a distance less than 0.5 m to observe the beam of
light. LED Class 2M. Not following these precautions can result in serious
injury to your eyes and in particular, your retina.
Attention:
LED Class 2M can cause injuries of your eyes even
without optical instruments in front of them or within a distance
of less than 0.5m and short exposure time.
Avoid direct radiation to your eyes!
7. To ensure proper operation, you must also follow the installation guide
described in chapter 2 of this manual. Operating the IImmpprreessssiioonn SSppoott oonnee
without suitable mounting devices can increase the risk of an accident.
8. The IImmpprreessssiioonn SSppoott oonnee features a unique small and lightweight design
with no specific carrying handles. Care needs to be shown when handling
the fixture to ensure that no unnecessary damage should occur. Fragile
areas include the LCD display and cover on one side arm and the front
bezel. Pressure in these areas could result in damages which will not be
covered by the standard warranty.
9. Repair, maintenance and installation work should only be performed by
qualified or GLP certified staff. You need to pay attention to the common
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
6
rules of technology that are not explicitly mentioned in this manual.
10. Use only original spare parts. Any structural modification on the system will
terminate all warranty claims.
11. Please keep this instruction manual for future reference.
2 Preparation and Installation
2.1 Mounting
The IImmpprreessssiioonn SSppoott oonnee is fully operational whether it hangs or is mounted to
a wall. It can also be operated while standing on the floor. Keep a safety
distance of 0.5 m from any easily inflammable materials (decoration etc.).
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217.
The installation shall be done by qualified personal only.
For the various mounting positions of the IImmpprreessssiioonn SSppoott oonnee (standing on
the floor, sideways or hanging) different accessories kits are available. Using
any required kits, along with the standard mounting connectors on the base of
the fixture, will ensure a safe and firm installation.
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
7
2.1.1 Mounting on the floor (upright)
To operate the IImmpprreessssiioonn SSppoott oonnee in an upright position, please use
the dedicated floor-stand which is shipped with all original fixtures. The
floor stand is mounted to the base of the
fixture using the two Camlock quarter turn
fasteners. Line up and engage the camlock
connectors from the floor stand into the base
of the fixture and turn the two fasteners 90°
to lock them. Do the opposite to release
them again. On both sides you'll find eyelets
to pull though a ratchet strap. This allows
additional bracing of the floor-stand during
upright operation.
2.1.1 Mounting in hanging position (Head down)
To operate the IImmpprreessssiioonn SSppoott oonnee in a hanging position, two omega
brackets can be mounted directly to the bottom of the base using the
four Camlock connectors.
M10
Gewinde
Camlock
Camlock
Camlock
Eyelet
thread
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
8
2.1.2 Mounting in sideways position
To operate the IImmpprreessssiioonn SSppoott oonnee in a sideways position, please use
an additional mounting bar, available from GLP or one of their agents.
This mounting bar is fixed via the four camlock quick-release connectors.
Two half-couplers or clamps are then used to hang fixture. This
technique is necessary to cope with the additional torque in this
mounting position. Never use the "Mounting in hanging position"
technique described above to secure the fixture in a sideway position, as
the fixtures base can become damaged, and a secure installation cannot
be assured.
2.2 Securing the device
Regardless of the mounting method of the IImmpprreessssiioonn SSppoott oonnee you'll have to
use a secondary safety wire. This safety wire can be attached to the fixture by
threading it through one of the two holes provided on the base of the fixture.
Ensure that the safety wire is securely fastened through the fixture and the
fixtures mounting support. Install a safety wire that can hold at least 10 times
the weight of the fixture.
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
9
2.3 Connections
2.3.1 Power Supply
Autosensing ~100-240 Volt AC, 50-60 Hz, earth contact type plug via
Powercon
Connected load 450 VA (W) <=> T8A (micro-fuse 6.3x32mm)
Disconnect from the mains supply before changing the fuse and
use only the above described micro-fuse type.
2.3.2 DMX
USITT DMX-512 Standard input/output via 3 pin and 5 pin connectors.
3 pole: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+]
5 pole: Pin 1 = [Ground] / Pin 2 = [-] / Pin 3 = [+] / Pin 4/5 n.c.
Ethernet (Artnet II compatible, ACN ready)
Neutrik RJ-45 plug (for Neutrik EtherCon connector with body)
3 The Menu Field
You’ll find the control board on the side of the arm. It allows you to make all necessary
adjustments of the IIMMPPRREESSSSIIOONN SSppoott OOnnee.. With the Menu-key you get into the main menu.
Afterwards you can navigate through the menu with the Touchwheel. Push the Enter-key to
get to the next menu level or to confirm your settings. Select ON/ OFF function settings with
the Touchwheel. Confirm and save with the Enter-key. Push the Back-key to cancel the
entry and go back to the main menu.
Back
- Enter
Layer 1 Layer 2 Layer 3 Layer 4 Notes
DMX Start
Address
Set the DMX start address
Personality Pan/Tilt
Pan/Tilt settings
Pan invert
Selects Inverse Pan, on or off
Tilt invert
Selects Inverse Tilt, on or off
Feedback
Automatic position feedback selection for
pan/tilt movement
DMX Address
Set the DMX start address
GLP German Light Products GmbH
(Instruction version 1.93) / from software version 1.52
10
Mode
Allows selection of the desired DMX Mode
Compressed
Fixture works in "Compressed" mode see
also section 4
Normal
Fixture works in "Normal" mode see also
section 4
HighResolution
Fixture works in "High Resolution" mode
see also section 4
Hold Values
Defines whether the last DMX signal is
stored, or the lamp is switched OFF in case
of signal interruption
Manual
Manual control of all system functions
Pan
Manual control
Tilt
Manual control
Color
Manual control
Red
Manual control
Green
Manual control
Blue
Manual control
Shutter
Manual control
Dimmer
Manual control
Color temp.
Manual control
Special
Manual control
Movement
Manual control
Movement
Speed
Manual control
Zoom
Manual control
Focus
Manual control
Gobo1
Manual control
Gobo 1 rot.
Manual control
Gobo 2
Manual control
Gobo 2 rot.
Manual control
Effectwheel
Manual control
Effectwheel
rot.
Manual control
Prism
Manual control
Iris
Manual control
Display
Adjustments for the Display
Blackout
Sets the display On or Off
Auto-Rotate
Display will rotate automatically
Display
invert
Display will rotate manual
Brightness
Display backlight
Loading...