GLP impression rgb 120 rz Instruction Manual
Instruction Manual
from software version 1.00/30
(Instruction version 1.0)
e-mail: service@glp.de
Internet: http://www.glp.de
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH (Instruction version 1.0) / from software version 1.00/30) 2
Notes:
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH (Instruction version 1.0) / from software version 1.00/30) 3
Table of content
1 Description of Device.............................................................................................. 4
1.1 Safety Instructions ............................................................................................ 5
2 Preparation and Installation ...................................................................................6
2.1 Mounting ...........................................................................................................6
2.1.1 Mounting on the Floor (Upright).............................................................7
2.1.2 Mounting in hanging Position (Head first)..............................................7
2.1.3 Mounting in sidewise Position ............................................................... 8
2.2 Secure the Device.............................................................................................9
2.3 Connections...................................................................................................... 9
2.3.1 Power Supply ........................................................................................ 9
2.3.2 DMX ......................................................................................................9
3 The Menu Field ...................................................................................................... 10
4 DMX Channel Selection (DMX Protocol) .............................................................12
5 Maintaining and Cleaning the IIMMPPRREESSSSIIOONN ....................................................... 17
5.1 Safety regulations ........................................................................................... 17
5.2 Circumference and Interval (rule-of-thumb).................................................... 17
6 Technical Specifications.......................................................................................18
7 Index .......................................................................................................................19
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH (Instruction version 1.0) / from software version 1.00/30) 4
1 Description of Device
1. Moving head (actively and
passively cooled)
2. Arm with various cooling
vents
3. LCD-Display/Menu (data
entry)
4. Base with various
connectors and Camlock
mounting system
1
2
3
4
5
base side 1
6
base side 2
7 8 9 1010
FUSE T4A
5. Power On/Off
6. DMX- Output (3 pole)
7. DMX- Input (3 pole)
8. Micro-fuse 5x20mm, T5A
9. Mains supply (Powercon)
10. 2x Safety eyes
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH (Instruction version 1.0) / from software version 1.00/30) 5
1.1 Safety Instructions
The IIMMPPRREESSSSIIOONN is a High-Tech Product. To guarantee a
smooth operation, it is necessary to respect the following rules.
The manufacturer of this device will not take responsibility of
damages through any disregard of the information in this
manual. Warranty claims also will be cancelled in case the
system casing is opened.
1. Make sure before putting the system into operation, that the fan and the air
inlets are clean and not blocked by anything.
2. It must be assured that the system-head can rotate unhindered throughout
his complete rotating range. A safety distance of at least 0.5 m to any easily
inflammable material (e.g. decoration material) must be adhered.
3. Attention!
Don’t touch the device during the operation. This can cause
injuries or damages.
4. The system doesn’t contain any maintainable parts. Don’t open it!
5. It is necessary to wait at least 15 minutes after disconnecting the AC before
changing the optical carrier. Pay attention to possibly hot parts of the
system. -- Danger of BURNING --
6. Never look directly into the beam of light or one of the LEDs.
Never use
optical apertures with a distance less than 0.5 m to observe the beam of
light. LED Class 2M.
You'll risk a serious injury of your eyes and in
particular of your retina.
Attention: LED Class 2M can cause injuries of your eyes even
without optical instruments in front of them or within a distance
of less than 0.5m and short exposure time.
Hence: Avoid direct radiation of your eyes!
7. To allow a secure operation, follow also the Installation guide described in
chapter 2. Operating the IIMMPPRREESSSSIIOONN without suitable safety aids like
Safety cables or clamps/hooks can increase the risk of an accident.
8. Repair-, maintenance- and installation work shall be done by qualified or
GLP certified staff only. You need to pay attention to the common rules of
technology that are not explicit mentioned in this manual.
9. Use only original spare parts. Any structural modification on the system will
terminate all warranty claims.
10. Please keep this instruction manual for later reference.
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH (Instruction version 1.0) / from software version 1.00/30) 6
2 Preparation and Installation
2.1 Mounting
The IIMMPPRREESSSSIIOONN is fully operational whether it hangs or is mounted to the
wall. It can also be operated while standing on the floor. Keep a safety distance
of 0.5 m towards any easily inflammable materials (decoration etc.).
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217.
The installation shall be done by qualified staff only.
For the various mounting positions of the IIMMPPRREESSSSIIOONN (standing on the floor,
sideways or hanging) different accessories kits are available. Through this a
safe and firm installation is assured. You'll find special connectors on the
bottom side of the system which are put to use here. In addition the front side of
the system is marked with (FRONT) as this is important for a even orientation
during installation.
Loading...