GLP impression R-G-B Instruction Manual
from software version 1.72/30
(Instruction version 1.26)
e-mail: service@glp.de
Internet: http://www.glp.de
R
-
G
-
B
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Instruction version 1.26) / from software version 1.72/30)
2
Notes:
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Instruction version 1.26) / from software version 1.72/30)
3
Table of content
1 Description of Device.............................................................................................. 4
1.1 Safety Instructions ............................................................................................ 5
2 Preparation and Installation ................................................................................... 6
2.1 Mounting ........................................................................................................... 6
2.1.1 Mounting on the floor (upright) ............................................................. 7
2.1.1 Mounting in hanging position (head down) .......................................... 8
2.1.1 Mounting in a sideway position ............................................................ 8
2.2 Securing the Device .......................................................................................... 9
2.3 Connections ...................................................................................................... 9
2.3.1 Power Supply....................................................................................... 9
2.3.2 DMX ................................................................................................... 10
3 The Menu Field ...................................................................................................... 10
4 DMX Channel Selection (DMX Protocol) ................................................................. 13
5
5 Maintaining and Cleaning the IIMMPPRREESSSSIIOONN ....................................................... 18
5.1 Safety regulations ........................................................................................... 18
5.2 Maintenance Intervals (rule-of-thumb) ............................................................ 18
6 Technical Specifications ...................................................................................... 19
7 Index ....................................................................................................................... 20
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Instruction version 1.26) / from software version 1.72/30)
4
1 Description of Device
1. Moving head (actively and
passively cooled)
2. Arm with various cooling
vents
3. LCD-Display/Menu (data
entry)
4. Base with various
connectors and Camlock
mounting system
1
2
3
4
5
base side 1
6
base side 2
7891010
FUSE T4A
5. Power On/Off
6. DMX- Output (3 pole)
7. DMX- Input (3 pole)
8. Micro-fuse 5x20mm, T4A
9. Mains supply (Powercon)
10. 2x Safety eyes
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Instruction version 1.26) / from software version 1.72/30)
5
1.1 Safety Instructions
The IIMMPPRREESSSSIIOONN is an advanced technology product. To
guarantee smooth operation, it is necessary to follow the
following instructions.
The manufacturer of this device will not take responsibility of
damages through any disregard of the information in this user
manual. Warranty claims will also be cancelled in the event of
the system casing being opened.
1. Make sure that before powering up the fixture, the fans and air inlets are
clean and not blocked by anything.
2. Before powering up the fixture, ensure that the moving head part of the
fixture can rotate unhindered through its full range of movement.
3. A safety distance of at least 0.5 m to any easily flammable material (e.g.
decoration material) must be adhered to.
4. Attention! Don’t touch the device during operation. Parts of the fixture can
become hot and can cause injuries and / or damages.
5. The system doesn’t contain any user serviceable parts. Opening the fixture
will void the manufacturers warranty.
6. Danger of burning. Wait at least 15 minutes after disconnecting the AC
power before changing the optical carrier on the fixture. Pay attention to
possible hot parts of the system.
7. Never look directly into the beam of light or one of the LEDs. Never use
optical apertures with a distance less than 0.5 m to observe the beam of
light. LED Class 2M. Not following these precautions can result in serious
injury to your eyes and in particular, your retina.
Attention: LED C
lass 2M can cause injuries of your eyes even
without optical instruments in front of them or within a distance
of less than 0.5m and short exposure time.
Avoid direct radiation to your eyes!
8. To ensure proper operation, you must also follow the installation guide
described in chapter 2 of this manual. Operating the IIMMPPRREESSSSIIOONN without
suitable mounting devices can increase the risk of an accident.
9. The IIMMPPRREESSSSIIOONN features a unique small and lightweight design with no
specific carrying handles. Care needs to be shown when handling the
fixture to ensure that no unnecessary damage should occur. Fragile areas
include the LCD display and cover on one side arm and the front bezel.
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Instruction version 1.26) / from software version 1.72/30)
6
Pressure in these areas could result in damages which will not be covered
by the standard warranty.
10. Repair-, maintenance- and installation work should only be performed by
qualified or GLP certified staff. You need to pay attention to the common
rules of technology that are not explicit mentioned in this manual.
11. Use only original spare parts. Any structural modification on the system will
terminate all warranty claims.
12. Please keep this instruction manual for future reference.
2 Preparation and Installation
2.1 Mounting
The IIMMPPRREESSSSIIOONN is fully operational whether it hangs or is mounted to a wall.
It can also be operated while standing on the floor. Keep a safety distance of
0.5 m from any easily inflammable materials (decoration etc.).
Pay attention to the regulations of: BGV C1 (former VBG 70)
and DIN VDE 0711-217.
The installation shall be done by qualified personal only.
R
R
R
-
-
-
G
G
G
-
-
-
B
B
B
GLP German Light Products GmbH
(Instruction version 1.26) / from software version 1.72/30)
7
For the various mounting positions of the IIMMPPRREESSSSIIOONN (standing on the floor,
sideways or hanging) different accessories kits are available. Using any
required kits, along with the standard mounting connectors on the base of the
fixture, will ensure a safe and firm installation.
1x M10
(length max.16mm)
2x Camlock
quick release
fasteners
front side of the fixture
2.1.1 Mounting on the floor (upright)
To operate the IIMMPPRREESSSSIIOONN in an upright position, please use the
dedicated floor-stand which ships with all original fixtures. The floor
stand is mounted to the base of the fixture using the two Camlock
quarter turn fasteners. Line up and engage the camlock connectors from
the floor stand into the base of the fixture and turn the two fasteners 90°
to lock them. Do the opposite to release them again. On both sides you'll
find eyelets to pull though a fixing strap. This allows additional bracing of
the floor-stand during the upright operation.
Loading...