GLP Creative Light 1 Akku LED Scheinwerfer, schwarz, Creative Light 1 Plus Akku LED Scheinwerfer, schwarz User Manual [EN]

Creative Light 1 (CL1)
Creative Light 1 Plus (CL1+)
User Manual
Revision 20210303-01
Document revisions
Revision number Notes Date released
Firmware v. 1.2.0
GLP® Creative Light 1 (CL1) and Creative Light 1+ (CL1+) User Manual
March 3, 2021
© 2020-2021 German Light Products GmbH. All rights reserved.
The marks ‘GLP’ and ‘German Light Products’ are trademarks registered as the property of German Light Products GmbH in Germany, in the United States of America and in other countries.
The information contained in this document is subject to change without notice. German Light Products GmbH and all affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Head office: German Light Products GmbH (GLP), Industriestrasse 2, 76307 Karlsbad, Germany Tel (Germany): +49 7248 92719 - 0
Service & Support EMEA: GLP, Industriestrasse 2, 76307 Karlsbad, Germany Tel. (Germany): +49 7248 9271955 Email: support@glp.de www.glp.de
Service & Support USA: GLP USA, 1145 Arroyo St., Ste. A, 91340 San Fernando, California Tel (USA): +1 818 767 8899 Support (US): info@germanlightproducts.com www.glp.de
Table of Contents
1. Safety ................................................................................................. 5
General safety information ......................................................... 5
Electrical safety ............................................................................ 6
Installation safety and protection from personal injury ........... 6
Battery safety ................................................................................ 7
2. Features ............................................................................................. 8
3. Product overview.............................................................................. 9
4. Control panel and display ............................................................. 10
Control panel display ................................................................ 10
Control panel functions ............................................................. 12
Accessing the control menus ................................................... 13
5. Preparing for use ............................................................................. 14
Charging ..................................................................................... 14
Transport lock ............................................................................. 15
Powering on and off .................................................................. 15
6. Configuring the CL1 ....................................................................... 16
Default control settings .............................................................. 16
Control options ........................................................................... 16
Fixture Settings ............................................................................ 17
Manual Control menu ............................................................... 18
Fixture and iQ.Mesh information .............................................. 18
Service ......................................................................................... 18
Loading factory backup ........................................................... 18
Linking to a CRMX Transmitter (CL1+ only) .............................. 19
DMX settings (CL1+ only) ........................................................... 19
Setting up iQ.Mesh control ........................................................ 19
7. Manual control................................................................................ 20
8. Infrared remote control .................................................................. 21
Pattern color ............................................................................... 22
Pattern Effects ............................................................................ 22
Effect Speed ............................................................................... 22
Global Intensity / Blackout ........................................................ 22
Automatic Colors ....................................................................... 23
Color changing type ................................................................. 23
Light output On/Off ................................................................... 23
9. Creative Light app control ............................................................ 24
Setting up the iQ.Mesh network ............................................... 24
Using the Creative Light app .................................................... 26
10. DMX control (CL1+ only) .............................................................. 28
Global intensity ............................................................................. 28
Global Shutter / Pattern Shutter .................................................... 28
Virtual color wheel ........................................................................ 29
RGB / Pattern RGB ......................................................................... 29
Control / Settings .......................................................................... 29
Pattern Control (available in Pattern DMX Mode) ................. 30
11. Mounting and installing ............................................................... 31
Temporary installation ............................................................... 31
Fixed installation ......................................................................... 31
Adding optical accessories ...................................................... 31
Securing with a safety cable .................................................... 32
Mounting on a UFO1 (Universal Fixing Object 1) .................... 32
Using an external power source ............................................... 32
12. Cleaning and product care ....................................................... 33
Suggested cleaning intervals ................................................... 33
Checking firmware version ....................................................... 33
Uploading new firmware ........................................................... 33
Battery care ................................................................................ 35
Caring for the environment ...................................................... 35
GLP Service and Support .......................................................... 35
13. Control menus .............................................................................. 36
14. DMX control modes overview (CL1+ only) ................................ 39
15. DMX channel index (CL1+ only) ................................................. 41
DMX Mode 1: Basic .................................................................... 41
DMX Mode 2: Pattern (default mode) ..................................... 43
DMX Mode 3: MultiPix ................................................................ 49
16. Technical Data ............................................................................. 50
17. Dimensions .................................................................................... 52
German Light Products®
1. Safety
Key to symbols
The following symbols are used in this manual:
Safety hazard.
Warning!
Risk of electric shock.
Warning!
Warning!
See user documentation
for important safety
information.
General safety information
Read this section carefully before installing the product. If you have any questions about the product, contact your GLP® supplier for assistance. Your GLP supplier will be happy to help.
Respect all warnings and directions given in this manual and on the product. Read this manual and familiarize yourself with the safety precautions it contains before installing or using the product. The manufacturer will take no responsibility for damages or harm resulting from disregard for the information in this manual.
Check the GLP website at www.glp.de and make sure that you have the latest version of this quick start guide.
Make this manual available to any person who is responsible for installing, operating or servicing the product.
Use the product only as directed in this manual. Observe all markings in this manual and on the product.
Do not modify the product in any way not described in this manual.
The LEDs that form the light source in this product are not replaceable.
Ensure that there is free and unobstructed airflow around the product.
Do not attempt to open the product. There are no user-serviceable parts inside.
Opening the product can create a safety risk and will void the product warranty. If the product becomes defective, contact your GLP supplier for assistance. Do not try to carry out repairs yourself.
5 Rev. 20210303-01
www.glp.de
Electrical safety
The product is for indoor use in dry locations only. Do not allow the product to become wet.
Disconnect the product from its charger before cleaning. Clean the product with a soft, dry cloth only. Do not clean with solvents or abrasive products.
Ensure that any equipment used to charge the product is electrically connected to ground (earth).
Disconnect equipment used to charge the product from power if the charging equipment, power plug, power cable, any cover or any other component is damaged, defective or deformed. Do not reapply power until the product has been repaired and made safe by a technician authorized by GLP.
Installation safety and protection from personal injury
Do not stare directly into the light output at close range. Looking into the light output at close range may cause eye injury or irritation.
Install the product in a dry, dust-free location where it will not be exposed to high temperatures or direct sunlight.
Ensure that the product is safely supported and cannot fall. If mounting the product on a wall or other vertical surface or structure, use fasteners that are suitable for the surface and strong enough to safely hold the weight of the product.
The product’s integrated magnet may be used for temporary installation on magnetic surfaces.
In permanent installations, fasten the product to a surface or structure with screws fastened into the threaded holes provided on the product or secure the product against falling by adding an approved safety attachment as directed in this manual.
Fasten the product to a structure or surface only as directed in this manual.
If there is any risk that the product may cause injury or damage if it falls, secure it
with an approved secondary attachment as described in this manual.
The product can become hot during normal operation. Take precautions to prevent accidental physical contact with the product. Allow to cool before handling.
CL1 / CL1+ User Manual
6
German Light Products®
Do not illuminate surfaces and objects that are less than 0.3 m (0.98 ft) from the product.
Keep the product away from flammable or volatile materials.
Battery safety
This product contains a rechargeable single-cell 3.7volt lithium-ion battery with a capacity of 10 000 mAh.
Respect all applicable laws and regulations for the transport, storage and disposal of batteries.
Do not expose the battery to fire or heat.
Protect the battery and product from physical shocks.
Do not allow the battery to come into contact with water.
Do not short-circuit a lithium-ion battery, or you may cause a battery explosion.
Charge the battery at an ambient temperature of between 15° C (59° F) and
35° C (95° F).
Do not charge the battery in an enclosed space. Leave the product’s container, tourpack case or flightcase open during charging.
Do not connect a battery charger to a product that may be damaged or faulty.
If the battery becomes faulty or will not hold a charge, replace it with an original
spare part from GLP only.
The battery must be serviced by authorized personnel only.
7 Rev. 20210303-01
www.glp.de
2. Features
The GLP Creative Light 1 (CL1) is a wireless, battery-powered visual effect fixture for the semi-professional event and professional entertainment market. Each CL1 has 24 individually controllable RGB pixels. Two different optical front screens are supplied with the CL1, as well as a USB-A to USB-C charging cable. You can charge the CL1 using any standard USB charger. A traveling multi-device case with integrated charging system is available as an optional accessory.
The CL1 is a highly advanced fixture in a compact package. It creates stunning light effects using the integrated dynamic FX engine or when driven by individual RGB pixel control. The fixture is perfect for setting creative visual highlights, illuminating walls or integrating into dark areas of sets. The CL1 lets you create impressive visual effects with minimal equipment size and budget.
Depending on the selected performance mode, the integrated battery can power visual effects for up to 10 hours with white output and 24 hours with single-color output.
The Creative Light 1 comes in two versions:
The Creative Light 1 (CL1) can be controlled by IR Remote Control, by mobile device via the GLP iQ.Mesh* system and GLP Creative Light app, and by use of the control panel on the front of the fixture.
The Creative Light 1 Plus (CL1+) offers all of the features of the CL1 but in addition it features integrated LumenRadio CRMX TiMo technology that allows control by wireless DMX.
This manual uses the name CL1 to refer to both the CL1 and CL1+ unless stated otherwise.
If you have any questions about the CL1, the CL1+, CRMX, DMX control or iQ.Mesh, for example, please contact your GLP supplier who will be happy to help you.
* iQ.Mesh is a new wireless mesh network technology available from GLP. iQ.Mesh allows fixtures to communicate with each other, share data and receive and amplify signals to set up huge networks. The GLP Creative Light smartphone app allows communication with the mesh network and direct fixture control.
When controlled via the app, CL1 fixtures can generate an iQ.Mesh wireless network with no need for any additional hardware. Each CL1 receives and amplifies the signal, allowing the network to cover long physical distances.
The GLP Creative Light app provides an intuitive user interface and allows fast, easy system setup. Multiple devices can be grouped for live control of intensity, strobe and pulse effects, background and foreground colors, a variety of dynamic patterns and sound-to-light audio triggering. The app is available from Play Store for Android and App Store for iOS.
CL1 / CL1+ User Manual
8
German Light Products®
3. Product overview
A
C
A – Monochrome OLED display
B – Sensor for IR remote control
C – 4 x control buttons
D – 24 x individually controllable RGB
LEDs
E – 3 x magnetic mounting points for
optical accessories
F – 3 x M6 threaded holes for mounting
fasteners and/or eyebolt for secondary attachment
B
D
E
Figure 1. Product overview
G
F
H
I
J
G – Slot for Kensington security lock
system
H – Mounting magnet embedded in
non-slip rubber
I – 2 x attachment points for secondary
attachment
J – USB-C connector for charging,
continuous power and service, two charging ports
9 Rev. 20210303-01
www.glp.de
V
w
N
4. Control panel and display
The control panel on the front of the CL1 consists of an integrated monochrome OLED display and four control buttons.
Control panel display
P01/S04/X04
10
1.2
The CL1’s OLED display shows the following information:
Main status display
If the CL1 or CL1+ is in Manual Mode:
If the CL1 or CL1+ is in iQ.Mesh mode:
If the CL1+ is in DMX Mode:
Charge status
Remaining battery charge.
Plug icon shows that the device is connected to power.
Increasing sectors in the battery icon indicate that the
Sho
N
Shows the selected Pattern, Speed and Crossfading settings. For example: P01/S04/X04 indicates Pattern 01, Pattern Speed 04 and XFade setting 04.
Shows iQ.Mesh status.
Shows the DMX Mode and the DMX Start Address. For example, DMX-M2-302 indicates DMX Mode, Control Mode 2 and DMX Start Address 302.
device is charging.
IR O
Audio triggering
CL1 / CL1+ User Manual
Internal audio triggering microphone enabled / disabled.
Audio triggering microphone sensitivity 1 (lowest) to 10
Software
Currently installed firmware version.
(highest).
10
German Light Products®
Power mode
N – Normal. Output is balanced for long performance with optimized output. Performance time depends on intensity level and color. Continuous performance without battery charges requires an external power supply of minimum 2 amps.
H – High Power. Output is optimized for highest brightness. Performance time depends on intensity level and color. Continuous performance without battery charges requires an external power supply of minimum 3 amps.
E – Eco. Output is optimized for longest performance time between battery charges. Performance time depends on intensity level and color. Continuous performance without battery charges requires an external power supply of minimum 2 amps.
Signal status
Show – Fixture is in Manual Mode. The standalone pattern can be selected using the IR remote control or the integrated control buttons.
No Signal (CL1+ only) – Fixture is in DMX Mode but is not receiving DMX data via CRMX. The fixture is following the settings that are currently active in the NO-SIGNAL BEHAVIOR menu.
DMX (CL1+ only) – Fixture is in DMX Mode and is receiving DMX data via CRMX.
Signal source
IR (ON) – Manual Mode is selected and IR remote control is enabled. You can control the fixture using the integrated control buttons (MANUAL CONTROL menu) or the IR remote control.
IR (OFF) – Manual Mode is selected and IR remote control is disabled. You can control the fixture using the integrated control buttons (MANUAL CONTROL menu).
CRMX (CL1+ only) – LumenRadio CRMX module is enabled and the CL1+ is ready to be controlled via DMX. The status of CRMX communication is indicated as follows:
Horizontal dashes – the CRMX module is
not linked to a CRMX transmitter.
Vertical bars – the CRMX module is linked
to a CRMX transmitter. The bars indicate signal quality.
11 Rev. 20210303-01
www.glp.de
Control panel functions
The CL1’s four control buttons have the following functions:
MENU button
Press and hold for 3 seconds: switch CL1 on and off.
Press once briefly: open the control menus for manual
control or configuration.
If you are in one of the control menus, press once briefly to exit the current menu without making any changes.
If the top-level control menu is active, press and hold for 20 seconds to carry out a hard reset. This will disconnect the battery from the controller for a few seconds while it fully restarts the CL1.
UP and DOWN buttons
Scroll up and down through menus.
If the display is activated and you see the main screen,
press and hold the DOWN button for 3 seconds to change the signal source
ENTER button
If you are in the control menus, confirm a selection or save a change.
If the top-level control menu is active, press and hold for 6 seconds to re-initialize the CL1 and return it to its original factory settings. All custom settings and control configuration settings will be deleted. NB: Re-initializing will return the DMX address to 001 and unlink the CL1 from any existing CRMX or iQ.Mesh link, so you may lose the connection to your controller.
MENU and ENTER buttons together
+
CL1 / CL1+ User Manual
If the top-level control menu is active, pressing and holding the MENU button and the ENTER button together for 6 seconds applies the transport lock and disables all the control buttons. We recommend that you apply the transport lock to avoid accidentally powering the CL1 on during transport or long-term storage.
To unlock the CL1, connect it to a charger.
12
German Light Products®
Accessing the control menus
To enter the CL1’s control menus:
See Figure 2. Press the MENU or ENTER control
button once to activate the display.
Press the MENU button to enter the menu structure.
Figure 2. Menu button
13 Rev. 20210303-01
www.glp.de
5. Preparing for use
Warning! Read ‘Safety’ starting on page 5 for important safety
information that you must understand before you charge, install or operate the fixture. Follow the warnings and instructions in the user documentation of all involved products during charging.
Important! Connect the CL1 to a USB power source and charge it to 100% before using it for the first time. To avoid draining the battery unnecessarily, power the CL1 off when not in use and apply the transport lock before long-term storage or transport.
Charging
Charge the CL1 to100% before using it for the first time.
When using the GLP Creative Light app, you can see the CL1’s current battery charge level on your smartphone.
USB-C
Docking
station
Figure 3. Charging options
See Figure 3. After unboxing the CL1 and before you switch it on, connect it to a source of USB power using the supplied USB-A-to-USB-C cable in order to charge it. The power source can be a laptop, USB charger or powerbank, for example, that can supply minimum 1 amp.
A 1 amp power supply is suitable for charging only: the CL1 must be powered off during charging. When operating the CL1 continuously under external power, the CL1 requires a current of minimum 2 amps in Normal and Eco power modes and 3 amps in High power mode. The CL1 is designed for use with normal and fast charging, but using USB superfast charging together with a USB-C to USB-C cable may result in the battery not being fully charged.
CL1 / CL1+ User Manual
14
German Light Products®
You can also charge multiple CL1 devices using the docking stations in the Creative Light 1 charging tourpack case that is available as an optional accessory from GLP suppliers. Leave the case open during charging.
See Figure 4. You can monitor the charging process as follows:
During charging, the first LED pixel flashes green (A) and the CL1’s display shows a charging symbol.
When the CL1 is fully charged, the first LED pixel lights constant green (B) for as long as the CL1 is connected to the charger.
When you disconnect the CL1 from the charger, the first LED pixel switches off (C).
Figure 4. Charging status
Transport lock
The CL1 ships with the transport lock applied. To unlock the CL1 when the transport lock is applied, connect it to a charger.
If you are going to transport the CL1 or put it into long-term storage, apply the transport lock. This disables all control buttons. To unlock the CL1 when the transport lock is applied, connect it to a charger.
Powering on and off
See Figure 5. To switch on the CL1, press and hold the MENU button for 3 seconds. The CL1’s LEDs will light up white in a circle show you that the fixture is starting up. The CL1 is now ready to use and you can start configuration.
To switch off the CL1 while it is powered on, press and hold the MENU button for 3 seconds. The CL1’s LEDs will light white and then turn off in a counterclockwise circle to show you that the CL1 is shutting down. You can now store the CL1 without draining the battery.
Figure 5. Powering on
15 Rev. 20210303-01
www.glp.de
6. Configuring the CL1
The menus in the control panel on the front of the CL1 give a range of options for configuring the fixture. See ‘Control menus’ on page 36 for an overview of the menus.
In the CL1+, a range of configuration options is also available via DMX on the Control / Settings DMX channel. See the DMX Channel Index section at the back of this manual for details.
The configuration options available are described in this chapter.
Default control settings
By default, the CL1 and CL1+ are set up as follows:
The CL1 is set to SIGNAL SOURCE: iQ.Mesh and NO-SIGNAL: MANUAL CONTROL. This means the fixture automatically switches to manual / IR remote control as long no valid iQ.Mesh Signal is being received or the fixture is not linked to the Creative Light smartphone app.
The CL1+ is set to SIGNAL SOURCE: CRMX and NO-SIGNAL: MANUAL CONTROL. This means the fixture automatically switches to manual / IR remote control as long no valid CRMX Signal is being received or the fixture is not linked to CRMX.
You can change these default settings in the fixture’s control menus under SIGNAL SETTINGS SIGNAL SOURCE and FIXTURE SETTINGS NO-SIGNAL BEHAVIOR. See the following sections for details.
Control options
To select a control method for the CL1:
Enter the control menus and use the UP and DOWN buttons to scroll to SIGNAL
SETTINGS. Press ENTER.
Scroll to SIGNAL SOURCE. Press ENTER.
Scroll to one of the following options and press ENTER to select:
CRMX (CL1+ only)
If you select CRMX, the letters CRMX appear in the bottom right-hand corner of The CL1+ display. You can now link the fixture to a CRMX transmitter. See ‘Linking to a CRMX Transmitter (CL1+ only)’ on page 19 for instructions. Once the fixture is linked you can control the CL1+ by DMX.
Note: Don´t forget to choose a DMX Control Mode in the CONTROL MODE menu and give the CL1+ a suitable DMX Address in the DMX ADDRESS menu.
iQ.Mesh
If you select IQ.MESH, the name iQ.Mesh appears in the bottom right-hand corner of the CL1 display. You can now link the CL1 to GLP’s iQ.Mesh network and Creative Light smartphone app. See ‘Creative Light app control’ on page 24 for instructions.
CL1 / CL1+ User Manual
16
German Light Products®
Manual / IR Remote
If you select MANUAL / IR REMOTE, IR appears in the bottom right-hand corner of the CL1 display followed by ON or OFF depending on whether IR remote control is enabled or disabled in the separate SIGNAL SETTINGS IR REMOTE CONTROL ON/OFF menu. You can now control the CL1 using the MANUAL CONTROL menu or using the infrared remote control that is supplied with the CL1. See ‘Manual control’ on page 20 and ‘Infrared remote control’ on page 21 for details of control options.
Tip! See Figure 6. As a shortcut, you can switch between control signal sources by pressing and holding the DOWN button for 3 seconds.
Figure 6. DOWN
button
Fixture Settings
No-signal Behavior lets you decide what the fixture should do if it is powered on but not receiving (or has not received) a control signal. You can set the CL1 to either black out, continue using the last commands it received via CRMX or iQ.Mesh, or switch over to manual control.
Mic Sensitivity adjusts the sensitivity of the CL1’s built-in microphone. The microphone is used for audio triggering, which gives you various options for synchronizing lighting changes with a music beat, for example.
If you set the CL1 to audio triggering and it does not respond to music, increase microphone sensitivity towards 10 (the highest sensitivity setting). If the CL1 responds too actively to music, reduce microphone sensitivity towards 1 (the lowest setting) until you obtain optimum performance.
Power Mode lets you choose how you prioritize light output versus length of operating time on one battery charge. There is a trade-off between these two parameters, or course. Power Mode lets you choose maximum light output, maximum operating time between battery charges or a good compromise between these two settings.
Emergency Light lets you define a static scene that the CL1 will display if it is connected to external power but then external power is disconnected. You can use Emergency Light as a control feature or as a way of providing emergency lighting in the event of a loss of power.
Default Settings returns the CL1 to its factory default settings without affecting its control configuration. Mic Sensitivity, No-Signal Behavior etc. are returned to their factory default settings, but DMX Address, Signal Source and Control Mode are not changed. The CL1’s default settings are printed in bold type in the control menus table starting on page 36.
17 Rev. 20210303-01
www.glp.de
Manual Control menu
The Manual Control menu lets you use the control panel on the front of the CL1 to display a static scene or run a dynamic pattern over the top of the main color. See full details under ‘Manual control’ on page 20.
Fixture and iQ.Mesh information
The Information menu lets you call up information about the CL1’s fixture software (firmware) versions and operating data. It also lets you call up information about the iQ.Mesh system and see the fixture’s current iQ.Mesh status.
Service
The Service menu gives three options for managing the CL1’s firmware and settings.
iQ.Mesh Upload prepares the CL1 for a firmware upload over an iQ.Mesh network using the GLP Creative Light smartphone app. See the section on ‘Uploading new firmware’ on page 33 for details.
Load Setting Defaults is identical to the Default Settings command in the Fixture Settings menu. It returns the CL1 to its factory default settings without affecting its
control configuration. Mic Sensitivity, No-Signal Behavior etc. are returned to their factory default settings, but DMX Address, Signal Source and Control Mode are not changed. The CL1’s default settings are printed in bold type in the control menus table starting on page 36.
Load Factory Backup re-initializes the CL1 completely. It returns the CL1 to its factory default settings including its factory-set control configuration. Mic Sensitivity, No-Signal Behavior etc. DMX Address, Signal Source and Control Mode are all returned to the original factory default settings. The CL1’s default settings are printed in bold type in the control menus table starting on page 36.
Important! A Load Factory Backup command will reset the CL1 to Manual / IR Remote control. Any link to CRMX or iQ.Mesh control will be cut off.
Loading factory backup
To re-initialize the CL1 and restore its original factory settings, switch the fixture on, then use a shortcut by holding the ENTER button pressed in for 6 seconds. The CL1’s individual configuration with all custom settings is returned to factory defaults.
Important! If you are using CRMX (CL1+ only) or iQ.Mesh control, note that loading factory backup returns the fixture to an unlinked state, breaking off communication with the CRMX link or iQ.Mesh network.
CL1 / CL1+ User Manual
18
Figure 7. Restoring factory
settings
German Light Products®
In the CL1+, the DMX address also returns to the factory default, which is 001.
To re-establish CRMX control, see below.
To re-establish iQ.Mesh control, see ‘Setting up iQ.Mesh control’ on page 19.
Linking to a CRMX Transmitter (CL1+ only)
Whenever CRMX is enabled and the CL1+ is not already linked, it searches for a LumenRadio CRMX transmitter.
To link the CL1+ with a new CRMX transmitter:
Enter the control menus, navigate to SIGNAL SETTINGS → SIGNAL SOURCE and
select CRMX.
Navigate to SIGNAL SETTINGS CRMX LINK and select LINK/UNLINK.
Start the linking process at the CRMX transmitter as described in the transmitter’s
user manual.
TIP: The quickest way of setting up multiple CL1+ fixtures for DMX use is to carry out a LOAD FACTORY BACKUP on each fixture by pressing and holding its ENTER Button for 6 seconds. This will return the fixture to factory settings and delete all CRMX and iQ.Mesh links. The fixtures are now ready for linking to a transmitter. After successful linking, set up the fixtures’ DMX addresses and DMX control mode.
DMX settings (CL1+ only)
When using DMX control via CRMX, you need to consider the following setup options.
DMX Address
If you want individual control of the CL1+ in an installation containing more than one fixture, you will need to give the CL1+ its own individual DMX address. Fixtures of the same type that share the same DMX address behave identically.
The CL1+ is set to DMX address 001 by default.
DMX Modes
The CL1 has three DMX control modes: Basic, Pattern and MultiPix modes. The different modes give you a choice of control options. See ‘DMX control modes overview (CL1+ only)’ starting on page 39 for details.
Setting up iQ.Mesh control
To set up a CL1 fixture so that you can control it with the GLP iQ.Mesh system and Creative Light smartphone app, open the control menus, navigate to SIGNAL SETTINGS SIGNAL SOURCE and select iQ.Mesh. See full details under ‘Creative Light app control‘ on page 24.
19 Rev. 20210303-01
www.glp.de
7. Manual control
If you set the CL1 to MANUAL / IR REMOTE CONTROL in the SIGNAL SETTINGS menu (you can also use a shortcut by pressing and holding the DOWN button to scroll through the control signal sources), you can control it manually using the CL1’s integrated control panel.
Manual control gives the same options as Pattern DMX Mode (see ‘DMX Mode 2: Pattern’ on page 39). Additionally, you can set changes between steps in patterns to snap (instant change from one step to the next) or crossfade (fade from one step to the next).
The control options available when using Manual control are as follows:
Master Intensity gives 0 – 100% continuous dimming of the complete fixture.
Main Color lets you set the LED pixels to display a custom RGB color, one of 30
color presets or one of 4 color chaser options.
FX Layer provides control of 40 patterns that can be superimposed over the main color with variable visibility and speed. You can control pattern intensity and color using RGB color mixing plus the color presets from the Color Wheel DMX channel.
Color Crossfade lets you set steps in the pattern to snap or fade to the next.
CL1 / CL1+ User Manual
20
German Light Products®
8. Infrared remote control
If you set the CL1 to SIGNAL SOURCE MANUAL / IR REMOTE CONTROL in the SIGNAL SETTINGS menu (you can also press and hold the DOWN button to scroll through the control signal sources), you can control it using the CL1’s integrated display and control panel or the supplied IR remote control unit.
The remote control unit has the following features:
Color presets
The twelve COLOR PRESET buttons select a fixed color preset for the color of the pattern.
Pattern presets
The sixteen PATTERN PRESET buttons select a dynamic pattern.
Effect speed
UP
Dimming
UP
DOWN
Color chase
Color changing type and Blackout (Light On/Off)
Figure 8. Remote control unit
21 Rev. 20210303-01
DOWN
www.glp.de
Pattern color
The color presets available when using the remote control unit are as follows:
Red
(CW01)
Orange
(CW08)
Amber
(CW14)
Note that a wider range of color presets is available using the fixture’s control panel.
Green
(CW02)
Yellow
(CW06)
Lime Green
(CW20)
Blue
(CW03)
Light blue
(CW11)
Pink
(CW09)
White 8000K
White 4200K
White 2700K
Pattern Effects
When you select a pattern effect, the pattern will always start with a default color and run at medium speed. Once you have selected the pattern preset, you can change the speed and color of the pattern using the PATTERN COLOR and SPEED buttons. 16 pattern effects are available:
Pattern 00 is the “open” pattern and will enable all 24 pixels. You can set the color by using the COLOR PRESET buttons.
Patterns 02 to 07 are dynamic patterns over a black background. You can select the pattern color by using the COLOR PRESET buttons.
Patterns 08 to 15 are dynamic patterns over a fixed color background. You can select the pattern color using the COLOR PRESET buttons. You cannot change the background color with the IR remote control unit (but you can change the background color using the MANUAL CONTROL menu in the CL1’s integrated control panel.
Note that a wider range of effect patterns is available using the fixture’s control panel.
Effect Speed
You can control the speed of a dynamic pattern using the SPEED UP and SPEED DOWN buttons. When you first select a pattern, it runs at medium speed until you adjust the speed using these buttons.
Global Intensity / Blackout
The DIMMER UP and DIMMER DOWN buttons control global light output intensity.
You can use the BLACKOUT button to temporarily toggle between light output and no output. The BLACKOUT button will only toggle output on and off: it will not change the selected dimmer value.
CL1 / CL1+ User Manual
22
German Light Products®
Note: You can control background and pattern intensity individually using the MANUAL CONTROL menu in the CL1’s integrated control panel.
Automatic Colors
Four Color Chaser buttons are available:
Auto Rainbow Colors – Automatic dynamic sequence of rainbow colors. You can adjust the color changing speed using the SPEED UP and SPEED DOWN buttons.
Auto Extended Colors – Automatic dynamic sequence of a selection of colors from the DMX color wheel. You can adjust the color changing speed using the SPEED UP and SPEED DOWN buttons.
Auto Extended Colors Random – This program is the same as “Auto Extended Colors” but colors are displayed in random order.
Music Trigger Rainbow Colors – This program is the same as “Auto Rainbow Colors” but color changes are triggered by the CL1’s internal microphone.
Color changing type
Three buttons let you set up and control color changing:
The SNAP button creates a snap chase: each color in the sequence snaps instantly to the next color.
The STOP button freezes automatic color changing at the current color.
The FADE button creates a crossfading chase: each color in the sequence fades
smoothly to the next color.
Light output On/Off
The BLACKOUT button toggles light output on and off.
23 Rev. 20210303-01
www.glp.de
9. Creative Light app control
If you select SIGNAL SOURCE iQ.MESH in the SIGNAL SETTINGS menu (you can also press and hold the DOWN button to scroll through the control signal sources), you can control the CL1 using the GLP Creative Light smartphone app.
Using the Creative Light app, a smartphone can communicate with CL1 fixtures using GLP iQ.Mesh technology in which each fixture is capable of relaying data to other fixtures. The mesh system allows wireless control of networks over large distances.
You can find guidance about using the Creative Light app in the app itself once you have installed it, so this manual only gives you brief instructions to get you started.
Note that the Creative Light app is constantly being updated, and the appearance of the app may differ from the screenshot pictures given in this section. This user manual will be updated to match the app, so make sure that you have the latest version of this user manual.
Setting up the iQ.Mesh network
To control an installation containing CL1 fixtures with the Creative Light app, you must first link the fixtures to and configure the iQ.Mesh network. To do this:
Download the GLP Creative Light app from the App Store (iOS) or Play Store
(Android). Pointing your smartphone at the correct QR code for your smartphone in Figure 9 will take you to the app:
Figure 9. QR codes to obtain GLP Creative Light app
Switch on all the CL1 fixtures and open the control panel menus. Make sure that
each fixture is unlinked from older iQ.Mesh Networks before linking. To unlink a CL1, either:
go to SIGNAL SETTINGS iQ.MESH LINK/UNLINK and unlink the CL1, or
use a shortcut by pressing and holding the ENTER button for 6 seconds to load
factory backup. This will return the CL1 to factory settings and delete any links to CRMX or iQ.Mesh.
CL1 / CL1+ User Manual
24
German Light Products®
Navigate to SIGNAL SETTINGS → SIGNAL SOURCE and select iQ.Mesh. You can
also use a shortcut by pressing and holding the DOWN Button to change the control signal source. When the CL1 is set to SIGNAL SOURCE iQ.Mesh, it will show a red rotating pixel to indicate that the fixture is not connected to an iQ.Mesh Network and is ready for linking.
Open the Creative Light app. See Figure 10. Tap on
the Setup and Configuration button (arrowed) in the top right-hand corner of the main screen to open the Setup and Configuration screen.
See Figure 11. In the LINKING
section at the bottom of the Setup and Configuration screen, tap on the Discovered Unlinked Devices button (arrowed). The app will search for unlinked devices. Each time it discovers a device it will add it to the list of discovered unlinked devices in the center of the screen.
Figure 11. Discovered Unlinked Devices
Figure 10. Setup and
Configuration
You can now either add all the fixtures in the installation or
add single fixtures to the network:
To add all the fixtures, see Figure 12. Tap on the Link all discovered devices button.
To add single fixtures, look down the list of discovered, unlinked devices in the center of the screen and tap on the CL1 that you want to add to the network. Then tap on the Link Selected Fixture button (see Figure 13) on the right of the screen.
As soon as a CL1 fixture is linked to the iQ.Mesh network, it
changes from showing a red rotating pixel to a green rotating pixel and the indicator light (top left in Figure 12) turns from red to green.
You can now control the CL1 using the Creative Light app.
Using the app is intuitive. You will also find tutorials in the app that will help you learn how to use the app’s features.
Figure 12. Link All
Discovered Devices
Figure 13.
Link Selected
Fixture
25 Rev. 20210303-01
www.glp.de
Using the Creative Light app
The GLP Creative Light app is arranged into three separate work areas:
Fixture Group Select area
Tapping on the Fixture Group Select button (see Figure 14) opens the Fixture Group Select area (see Figure 15).
This area lets you select which fixture groups should be controlled.
Figure 14. Fixture Group Select button
Buttons at the bottom of the screen let you:
highlight a group in order to identify it in the installation,
select all groups,
de-select all groups (NONE), and
clear all group programming.
Main / Live Area
The Main / Live area lets you control light output, select color and select dynamic effects.
The CL1 system lets you work in two layers:
The first two pages (tap on the MASTER and MAIN buttons at the bottom of the screen) let you set the global intensity, select global intensity effects and choose a main color.
The next four pages (tap on the PATTERN buttons at the bottom
Figure 15. Fixture Group Select area
Figure 16. Main / Live area
CL1 / CL1+ User Manual
26
German Light Products®
of the screen) give control of a second layer, the pattern layer, which will always appear on top of the main layer. As long the intensity of this layer is set to zero, the pattern layer is transparent and not visible. If you set pattern intensity to 100%, the layer is fully visible on top of the main layer. For the Pattern layer you can set intensity, intensity effects, colors and different pattern effects.
Playback Area
Tapping the Playback button (see Figure 17.) opens the Playback area, where you can save individual light settings from the Main/Live area.
Figure 17. Playbacks button
The Playback area lets you store or recall light scenes.
See Figure 18. The 24 Playback buttons on the left are permanent playback buttons. The 8 buttons on the right are temporary flash playback buttons.
To store a light scene from the Main/Live area, enable recording by pressing and holding the REC button (arrowed) for 3 seconds and then save the scene to one of the Playback buttons.
You can also lock the Playback area by tapping and holding the lock button for 3 seconds. This will help you avoid deleting or storing playbacks by accident.
If you would like to learn more about the Creative Light app, please visit our homepage at www.glp.de.
Figure 18. Playback area
27 Rev. 20210303-01
www.glp.de
10. DMX control (CL1+ only)
If you set the fixture to SIGNAL SOURCE CRMX in the SIGNAL SETTINGS menu (you can also press and hold the DOWN button to scroll through the control signal sources), you can control the CL1+ using a DMX signal sent via a CRMX wireless DMX transmitter. The CL1+ has three DMX control modes, with the following possibilities.
Global intensity
The intensity channel provides dimming of the fixture in 8-bit resolution on channel 1 in all DMX modes.
Global Shutter / Pattern Shutter
You can apply a shutter / strobe effect to the whole fixture in all DMX modes. In Pattern DMX Mode, you can also apply the shutter / strobe effect to any pattern that you have superimposed onto the main ‘scene’. The control options available for the whole fixture and for the pattern are the same:
Closed blacks out the fixture.
Music Trigger Flash gives one single flash each time you change the DMX value in
this slot range. This option lets you manually send flashes whenever you like. This could be in time with a music beat, for example.
Random Pulse is a shutter pulse that rhythmically increases and decreases output. You can adjust the rate of the pulse by changing the DMX value within this slot range.
Random Pulse Open fades light in and then snaps to blackout. You can adjust the rate of the pulse by changing the DMX value within this slot range.
Random Pulse Close fades light out and then snaps to full. You can adjust the rate of the pulse by changing the DMX value within this slot range.
Random Double Flash performs a fast double flash. You can adjust the speed of the double flash by changing the DMX value within this slot range.
Strobe Random Pixel sets individual pixels to flash at random, giving a kind of sparkle effect. You can adjust the rate of the sparkle by changing the DMX value within this slot range.
Strobe Random All flashes all the fixture’s pixels together with a random interval between flashes. This lets you set up a classic effect consisting of a random strobe running on multiple fixtures. You can adjust the speed of the random flashes by changing the DMX value within this slot range. Note that the random effect between
multiple fixtures really is totally random!
Strobe Sync All flashes all of the pixels of multiple fixtures in a perfectly synchronized strobe effect. You can adjust the speed of the strobe by changing the DMX value within this slot range.
Open gives full intensity continuous output.
CL1 / CL1+ User Manual
28
German Light Products®
Virtual color wheel
The virtual color wheel channel gives quick access to fixed color presets. You can set the fixture to change from one color preset to another automatically with variable speed or in time with a music beat. You can decide whether the CL1 should snap from one color to the next or crossfade with variable fade time.
You can apply the color wheel effect to the whole fixture in Basic and Pattern DMX modes. In Pattern DMX Mode, you can also apply the color wheel effect to any pattern that you have superimposed onto the main ‘scene’.
Note that the color wheel has higher priority than the RGB channels. The virtual color wheel channel must be set to DMX value 000 before you can use RGB color mixing.
The color wheel control options available for the whole fixture and for the pattern are the same:
The first part of the color wheel channel (values 000 → 123) selects one of 30 color presets.
The second part of the color wheel channel (values 128 → 191) gives automatic changing between color presets with a snap (instant) change. You can vary the color change rate from slow to fast, or you can link the instant color changes to the CL1’s integrated audio trigger microphone. When using audio triggering you can decide whether a color change is triggered every beat or every 4, 8 or 16 beats.
The third part of the color wheel channel (192 → 255) gives automatic changing between color presets with a smooth crossfade. You can vary the crossfading rate from slow to fast, or you can link the crossfading color changes to the CL1’s integrated audio trigger microphone. When using audio triggering you can decide whether a color change is triggered every beat or every 4, 8 or 16 beats.
RGB / Pattern RGB
The RGB channels available in Basic and Pattern DMX Modes let you mix custom colors on all the fixture’s pixels together (the main ‘scene’) and on any pattern that you select to run on top of the main ‘scene’. Color mixing uses separate Red, Green and Blue intensity control.
The options for mixing custom colors on the whole fixture and on the superimposed pattern are identical.
Control / Settings
A special channel available in all DMX modes lets you modify some important fixture settings by DMX. Remotely adjust settings like this can be very helpful if fixture performance needs to be adjusted during the show or simply to create special scenes.
For most of these settings you need to send the required DMX value and then hold it for a certain number of seconds to activate.
29 Rev. 20210303-01
www.glp.de
Pattern Control (available in Pattern DMX Mode)
The different FX Pattern sequences available in Pattern DMX Mode can be superimposed onto the main ‘scene’ (the background). Each pattern consists of a sequence of steps and has active and inactive pixels. An active pixel shows the selected pattern color while an inactive pixel is fully transparent and will let the main ‘scene’ shine through.
Pattern effects are controlled with their own Pattern Master Intensity, Pattern Shutter, Pattern Color Wheel and Pattern RGB channels, which means that you can fade pattern effects in and out and apply intensity effects to patterns.
Pattern Intensity
The Pattern Intensity channel lets you set the intensity or visibility of the selected pattern. At 0% the pattern is invisible, and as you increase the DMX value on this channel the Pattern becomes more visible on top of the main ‘scene’ (the background). Patterns have priority over the main scene: if you increase the value on the Pattern Intensity channel from 0% to 100%, the pixels that are active in the pattern will crossfade from the main scene color to the pattern color.
Pattern Shutter
The Pattern Shutter channel offers the same effects as the Global Shutter channel (see ‘Global Shutter / Pattern Shutter’ on page 28).
Pattern Select
The Pattern Select channel gives access to 40 dynamic pattern effects.
Pattern 00 (DMX value 000) is the basic pattern and simply sets all pixels to be active.
Patterns 01 to 40 are dynamic patterns. Each dynamic pattern consists of multiple static pattern steps. The number of steps can be different in different patterns.
Random Pattern change lets you automatically change pattern effects from slow (change pattern every 30 seconds) to fast (change pattern every second). You can also link pattern changes to the CL1’s integrated audio triggering microphone. When using audio triggering you can decide whether a pattern change is triggered every beat or every 4, 8 or 16 beats.
Pattern Step/Speed
A pattern consists of a sequence of pattern steps. On the Pattern Step / Speed channel, you can:
scroll to and select individual steps,
take the change from one pattern step to the next and link it to the integrated
audio triggering microphone with a 1:1 beat trigger, or
set a pattern to run continuously with variable speed in different directions (clockwise or counterclockwise).
CL1 / CL1+ User Manual
30
German Light Products®
11. Mounting and installing
Warning! Follow the safety precautions given at the beginning of this
manual when installing the CL1. Follow the safety regulations that are applicable in your region when installing the CL1 overhead. If the CL1 can
cause injury or damage if it falls, secure it as described below with a secondary attachment such as a safety cable that is approved for the weight of the CL1.
You can install the CL1 in any orientation in a dry location.
Temporary installation
You can attach the CL1 to any magnetic surface by simply placing it on the surface. The magnet on the back of the CL1 is strong enough to hold the CL1 in position on a vertical surface. Non-slip rubber around the magnet helps to prevent the CL1 from sliding on the surface.
Secure the CL1 with a safety cable as described below if it can cause injury or damage if it falls.
Fixed installation
On surfaces or rigging trusses, use the integrated M6 threaded holes on the back of the CL1 for screws or bolts. All fasteners and attachments must be suitable for the purpose and environment.
GLP can supply optional installation and safety hardware for a wide range of applications. See ‘Mounting on a UFO1 (Universal Fixing Object 1)’ on page 32, for example.
Adding optical accessories
See Figure 19. Two front screens are supplied with the CL1: a clear screen for protection and a diffuser that softens the light.
To install a front screen, place its three magnetic mounts onto the magnetic mounting points on the front of the CL1 (see ‘Product overview’ on page 9). Screens are held in place magnetically.
To remove a front screen, simply lift it off the magnetic mounting points on the CL1.
Figure 19. Front screens
31 Rev. 20210303-01
www.glp.de
Securing with a safety cable
Follow the safety regulations of your region when using the CL1 overhead. If the CL1 can cause injury or damage if it falls, secure it with a secondary attachment such as a safety cable that is approved for the weight of the CL1.
To secure the CL1:
See ‘Product overview’ on page 9. Fasten the included M6 Eyebolt into one of
the three M6 threaded holes on the back of the CL1.
Attach a safety cable to the eyebolt and to a secure anchoring point so that it
will hold the CL1 if it falls. Take up as much slack as possible in the safety cable.
Mounting on a UFO1 (Universal Fixing Object 1)
See Figure 20. The UFO1 (Universal Fixing Object
1) from GLP simplifies mounting and removing the CL1 from rigging trusses, microphone stands, camera tripods, flat surfaces, etc.
D
To mount the UFO1, you can:
permanently fasten the UFO1 to a surface in any orientation using two screws A passed through the 4 mm holes in its center,
fasten the UFO1 to a camera tripod or other photographic equipment stand, microphone stand etc. using the 1/4"-20 UNC and 3/8”-16 UNC threaded holes B provided on either side of the UFO1, or
fasten a rigging clamp to the UFO1 by fastening a bolt into the M10 threaded hole C in the center of the UFO1. You can then fasten the rigging clamp to a rigging truss.
Once you have mounted the UFO1, you can then stick the CL1 to the UFO1 using the CL1’s magnetic mount. You can then remove the CL1 for charging and replace instantly thanks to the magnetic mounting system.
The UFO1 provides eyelets D as anchoring points for safety cables. The eyelets can also be used to support USB cables to provide permanent power, for example.
B
Figure 20. CL1 UFO
C
A
Using an external power source
For continuous operation with no need to recharge the CL1’s battery, it is possible to connect the CL1 to a power source via a USB cable connected to the CL1’s USB-C input connector.
The power source must be capable of safely supplying a constant operating current of:
2 amps with the CL1 in Normal power mode, and
3 amps with the CL1 in High power mode.
CL1 / CL1+ User Manual
32
German Light Products®
12. Cleaning and product care
Warning! There are no user-serviceable parts inside the CL1. Do not
attempt to open the CL1 or you may void the product warranty. Do not use water or any other liquid for cleaning.
Suggested cleaning intervals
The CL1 requires occasional cleaning to prevent the buildup of dust and dirt. The cleaning schedule depends on the operating environment.
Pay special attention to the LEDs, control panel display and IR remote control sensor (see ‘Product overview’ on page 9). Failure to keep the LEDs clean will significantly reduce light output and may cause damage. Regular cleaning will ensure maximum performance and reliable operation.
Use a soft, dry cloth only for cleaning. Do not use solvents or abrasive products of any kind. Apply only gentle pressure to the LEDs.
Checking firmware version
We recommend that you always have the latest firmware installed. Firmware, user documentation and other information about GLP products are available from the GLP website at www.glp.de.
You can check the CL1’s firmware in the top right-hand corner of the CL1’s integrated display. For details of the CL1’s internal drivers, open the control menus and then scroll to and open the INFORMATION menu.
Uploading new firmware
The easiest way to upload new firmware to a CL1 is to use the Creative Light app to send the firmware over an iQ.Mesh Network.
It is also possible to upload new firmware using the optional DPROG firmware uploader hardware from GLP and a DMX-to-USB-C adapter. Contact your GLP supplier for more information.
Uploading with DProg
If you wish to upload firmware using GLP’s DProg system, you will need the CL1 firmware package (software and change log file), a DMX to USB-C adapter cable and a D3-Prog uploader device from GLP.
To update the CL1’s firmware using a D3-Prog device:
Upload the required firmware version to the D3-Prog device.
Connect the D3-Prog device to the CL1 using the DMX to USB-C adapter cable.
Switch on the CL1.
Select the CL1 firmware file in the D3-Prog device.
33 Rev. 20210303-01
www.glp.de
Start the upload process via DMX (Prog. via RS485/DMX). The CL1 display should
show “UPDATE / Receiving Data” and a status bar. After a successful upload, FINISH appears in the display and the device switches off.
Uploading with iQ.Mesh
If you wish to upload firmware using the GLP Creative Light app, you will need a smartphone running the latest version of the app and the CL1 fixtures must be linked in a GLP iQ.Mesh network. The Creative Light app will always have the latest CL1 firmware if you keep the app updated via the Play Store (Android) or App Store (iOS).
Updating firmware involves two steps:
Check the iQ.Mesh firmware version and update if necessary.
Check the CL1 main firmware version and update if necessary.
Step 1 – Updating the iQ.Mesh firmware
To update the CL1’s iQ.Mesh firmware over an iQ.Mesh network using the Creative Light app:
Switch on the CL1, open the control panel menus and set
SIGNAL SOURCE SIGNAL SETTINGS to iQ.MESH.
Open the Creative Light app. See Figure 21. Tap on the
Setup and Configuration button in the top right-hand corner of the screen.
If the CL1 is discovered by the app, its name will appear in the
UNLINKED DEVICES list. Next to the name of each CL1 you will see two different version numbers such as 1.2.0 / 4.0.2. The first number is the CL1’s currently installed main firmware version. The second number is the CL1’s iQ.Mesh module firmware version. Keep both versions up to date.
If the CL1’s iQ.Mesh firmware is out of date, its version number will
be displayed in red. In this case, select the CL1 in the list and tap on the Firmware Update button (see Figure 22) on the right-hand side of the screen to carry out the iQ.Mesh firmware update.
Step 2 – Updating the CL1’s main firmware
Keeping the CL1 selected in the UNLINKED DEVICES list, tap on the
Link Fixture button (see Figure 23) on the right-hand side of the
screen.
Figure 21. Setup
and Configuration
Figure 22.
Firmware
Update
Once the CL1 is linked in the Creative Light app, switch to the
LINKED DEVICES page and check that the CL1 now appears in the LINKED DEVICES list.
If the CL1’s fixture firmware is out of date, its version number will be
displayed in red. In this case, select the CL1 in the list and tap on the Firmware Update button (see Figure 22) on the right-hand side of the screen to carry out the update.
CL1 / CL1+ User Manual
34
Figure 23.
Link Fixture
German Light Products®
Tip! Tapping and holding the Firmware Update button (see Figure 22) will update the firmware of all the fixtures in the list one by one.
Battery care
To get the best performance from the CL1’s lithium-ion rechargeable battery:
Recharge the battery immediately when it is discharged.
Charge the battery fully before storing the product. Partially charged batteries
lose capacity. Charge the battery every six months when the product is not in use.
Apply the transport lock by holding MENU and ENTER pressed in together for 6 seconds before transporting the CL1.
Apply the transport lock before putting the CL1 into storage.
Caring for the environment
Protect the environment:
Send the product’s packaging for recycling.
Send the CL1 to an authorized recycling center at the end of its
lifetime. Make sure that the battery is processed specifically as a lithium-ion battery.
Do not dispose of the product or battery with household waste.
GLP Service and Support
Contact information for the nearest GLP Service and Support is available online at www.glp.de/en/service, by email at info@glp.de, or by telephone at the following numbers:
GLP Germany: +49 (7248) 927 19-55
GLP N. America: +1 818 767-8899
GLP UK: +44 1392 690140
GLP Asia: +852 (3151) 7730
GLP Nordic: +46 737 57 11 40
35 Rev. 20210303-01
www.glp.de
13. Control menus
This chapter gives the contents of the menus in the control panel on the front of the CL1.
The menu items marked in yellow are available in the CL1+ only.
DMX Address
1-512 Set fixture’s DMX address
Control Mode
All LED pixels controlled together.
M1 - RGB
M2 - Pattern
M3 - MultiPix
Signal Settings
CRMX
Signal source
CRMX Link/Unlink
iQ.Mesh Link/Unlink
IR Remote control On/Off
Fixture Settings
No-signal behavior
Mic sensitivity 01 … 05 … 10
iQ.Mesh
Manual / IR Remote
Unlinked / Linked
Unlinked / Linked
On / Off
Blackout
Hold last value
Manual Control
Controllable color and intensity plus shutter/intensity effects and a Control/Settings channel.
Global intensity and shutter control. Color control of all LED pixels together in base layer. Top layer (Layer 2) with patterns can be superimposed onto base layer.
Global intensity and shutter control. Individual color control of each LED pixel.
Only CRMX signal is active, all other control signal sources are ignored
Only iQ.Mesh signal is active, all other control signal sources are ignored
Fixture controlled by its own control buttons and display or by infrared remote if IR Remote is enabled (see below)
Shows current CRMX linking status. Press ENTER to unlink (confirm 3s)
Shows current iQ.Mesh linking status. Press ENTER to unlink (confirm 3s)
Fixture responds to / ignores signal from infrared remote
If no control signal present, fixture blacks out
If no control signal present, fixture continues to use last valid control signal received
If no control signal present, fixture goes into manual control mode
Adjust sensitivity of audio triggering microphone, low ( 01) to high (10) sensitivity
CL1 / CL1+ User Manual
36
German Light Products®
Fixture performs at maximum brightness. Reduced operating time per battery charge. If battery is discharged, light switches off immediately.
Fixture finds good balance between brightness and operating time per battery charge. If battery is discharged, light switches off immediately.
Reduced brightness for longer operating time per battery charge. If battery is discharged, light switches off immediately.
Enables shift to Emergency Light scene if external power is disconnected
0 … 100% intensity of RGB in Emergency Light scene
Captures current DMX values for RGB on channels 5 + 6 + 7 and uses them for Emergency Light scene
Returns individual fixture settings and manual control settings to default values (bold settings) so that all fixtures behave identically. NB: Signal configuration is not changed: this command does not affect DMX Address, Signal Source, Control Mode, etc. Connection to controller will not be lost.
Power Mode
Emergency Light
Load Default Setting
Manual Control
High
Normal
Eco
Enable / Disable
Scene Settings
Capture DMX Confirm
Confirm 3 sec.
Enable
Disable
Red
Green
Blue
Master Intensity
Main Color
FX Layer
Color Crossfade
0 … 100% Global output intensity
Red 0 … 100%
Green 0 … 100%
Blue 0 … 100%
Color Wheel 00 (open)…01..12
FX Intensity 000 … 100% Pattern visibility
FX Pattern Select 00 (All) … 01 … 40 Pattern selection
FX Speed 00 … 10
FX Red 000 … 100%
000 … 100%
FX Blue
FX Color Wheel
Snap
Fade
000 … 100%
00 (open) … 30 …
CW1 … CW4
RGB intensity
Background color preset selection. Has higher priority than RGB setting.
Speed of selected pattern and color wheel. One direction only.
RGB adjustment of pattern color FX Green
Pattern color preset selection. Has higher priority than RGB setting.
Adjust crossfading time between steps in pattern
37 Rev. 20210303-01
www.glp.de
Information
SW Version Fixture software (firmware) version
BL Version Bootloader version Device Information
HW Version
Lamp Hours
Charging Cycles
Fixture hardware version
Number of hours LEDs are powered on
Number of battery charging cycles
iQ.Mesh Information
Service
iQ.Mesh Upload
Load Setting Defaults
Load Factory Backup
iQ.Mesh Version iQ.Mesh firmware version
iQ.Mesh Status Info iQ.Mesh system status
Confirm 3 sec.
Confirm 3 sec.
Sets up the fixture to receive manual upload of iQ.Mesh module firmware.
Returns individual fixture settings and manual control settings to default values (bold settings) so that all fixtures behave identically.
Signal configuration is not changed: this command does not affect DMX Address, Signal Source, Control Mode, etc. Connection to controller will not be lost.
Returns individual fixture settings, manual control settings and all signal configuration settings to default values (bold settings) so that all fixtures behave identically.
Important: this command affects DMX Address, Signal Source, Control Mode, etc. Connection to controller will be lost.
CL1 / CL1+ User Manual
38
German Light Products®
14. DMX control modes overview (CL1+ only)
The following DMX control modes are available in the CL1+.
DMX Mode 1: Basic
DMX Mode 1: Basic uses 7 DMX channels.
Basic Mode provides dimming, shutter/strobe effects, a Control/Settings channel that lets you configure the fixture remotely via DMX, a virtual color wheel for fast access to color presets, and RGB color mixing. All of the fixture’s pixels are controlled together.
Mode 1
Basic
1 Global intensity 2 Global shutter / strobe 3 Control / Settings 4 Virtual color wheel (color presets) 5 Red 6 Green 7 Blue
DMX Mode 2: Pattern
DMX Mode 2: Pattern is the default DMX control mode. It uses 15 DMX channels.
Channels 1 – 7 in Pattern Mode are identical with Basic Mode. These channels provide dimming, shutter/strobe effects, a Control/Settings channel that lets you configure the fixture remotely via DMX, a virtual color wheel for fast access to color presets and RGB color mixing. These effects form the fixture’s main ‘scene’.
In addition to the above, Pattern Mode offers a powerful effects engine on channels 8 – 15 with 40 dynamic effect patterns that run on the fixture’s 24 pixels. Patterns are superimposed onto the fixture’s main scene. In other words, the main scene becomes a background for the pattern.
Mode 2 Pattern
1 Global intensity 2 Global shutter / strobe 3 Control / Settings 4 Virtual color wheel (color presets) 5 Red 6 Green 7 Blue 8 Pattern visibility
9 Pattern shutter/strobe 10 Pattern select 11 Pattern step select / pattern speed 12 Pattern color wheel (color presets) 13 Pattern Red 14 Pattern Green 15 Pattern Blue
39 Rev. 20210303-01
www.glp.de
DMX Mode 3: MultiPix
DMX Mode 3: MultiPix uses 15 DMX channels.
Channels 1 – 3 in MultiPix Mode are identical with the other DMX modes. These channels provide dimming, shutter/strobe effects and a Control/Settings channel that lets you configure the fixture remotely via DMX.
In addition to these three channels, MultiPix Mode provides individual RGB control of each of the fixture’s 24 pixels.
Pixels in the CL1 are numbered starting at the top and moving around the fixture in
1 Global intensity
2 Global shutter / strobe
3 Control / Settings
4 Pixel 01 Red
5 Pixel 01 Green
6 Pixel 01 Blue
7
RGB control of pixels 02 → 23
in sequence
72
73 Pixel 24 Red 74 Pixel 24 Green 75 Pixel 24 Blue
Mode 3
MultiPix
a clockwise direction:
12 o’clock = Pixel 1
3 o’clock = Pixel 6
6 o’clock = Pixel 12
9 o’clock = Pixel 18
CL1 / CL1+ User Manual
40
German Light Products® DMX Mode 1: Basic
15. DMX channel index (CL1+ only)
This section lists the commands available via DMX in the CL1+ fixture’s three DMX modes.
DMX Mode 1: Basic
7 DMX Channels
Channel Command
Global
1
intensity
Global intensity 0100% 0 255 0 100 0 Fade
DMX
range Percent
Default
DMX Fade
Shutter closed Music trigger flash 5 9 2.0 3.5 Snap Random pulse slow fast 10 39 3.9 15.3 Fade Random opening pulse slow fast 40 69 15.7 27.1 Fade
Global
2
shutter
Control /
3
Settings
Random closing pulse slow fast 70 99 27.5 38.8 Fade Random double flash slow fast 100 129 39.2 50.6 Fade Random pixel strobe slow fast 130 159 51.0 62.4 Fade Random all strobe slow fast 160 199 62.7 78.0 Fade Strobe sync all pixels 1Hz 10Hz 200 250 78.4 98.0 Fade Open 251 255 98.4 100 Snap No function 0 11 0 4.2 No signal: Blackout (3s hold) 12 15 4.7 5.9 No signal: Hold (3s hold) 16 19 6.3 7.5 No signal: Manual Control (3s hold) 20 23 7.8 9.0 No function 24 39 9.4 15.3 Mic sensitivity: 10 (high, 1s hold) 40 43 15.7 16.9 Mic sensitivity: 09 (1s hold) 44 47 17.3 18.4 Mic sensitivity: 08 (1s hold) 48 51 18.8 20.0 Mic sensitivity: 07 (1s hold) 52 55 20.4 21.6 Mic sensitivity: 06 (1s hold) 56 59 22.0 23.1 Mic sensitivity: 05 (1s hold) 60 63 23.5 24.7 Mic sensitivity: 04 (1s hold) 64 67 25.1 26.3 Mic sensitivity: 03 (1s hold) 68 71 26.7 27.8 Mic sensitivity: 02 (1s hold) 72 75 28.2 29.4 Mic sensitivity: 01 (low, 1s hold) 76 91 29.8 35.7 Emergency light OFF (3s hold) 92 95 36.1 37.3 Emergency light ON (3s hold) 96 99 37.6 38.8 Emergency light Capture RGB values (3s hold) No function 104 223 40.8 87.5 Power mode High (3s hold) 224 227 87.8 89.0 Power mode: Normal (3s hold) 228 231 89.4 90.6 Power mode: Eco (3s hold) 232 235 91.0 92.2 No function 236 239 92.5 93.7 Load default settings (5s hold) 240 243 94.1 95.3 No function 244 255 95.7 100.0
0 4 0 1.6
100 103 39.2 40.4
Snap
255
0 Snap
41 Rev. 20210303-01
DMX Mode 1: Basic www.glp.de
00 - Open 0 3 0.0 1.2 01 - Red 4 7 1.6 2.7 02 - Green 8 11 3.1 4.3 03 - Blue 12 15 4.7 5.9 04 - Cyan 16 19 6.3 7.5 05 - Magenta 20 23 7.8 9.0 06 - Yellow 24 27 9.4 10.6 07 - Orange 28 31 11.0 12.2 08 - Deep Orange 32 35 12.5 13.7 09 - Pink 36 39 14.1 15.3 10 - Deep Purple 40 43 15.7 16.9 11 - Light Blue 44 47 17.3 18.4 12 - Deep Amber 48 51 18.8 20.0 13 - Light Amber 52 55 20.4 21.6 14 - Deep Golden Amber 56 59 22.0 23.1 15 - Straw 60 63 23.5 24.7 16 - Sunset red 64 67 25.1 26.3 17 - Light Pink 68 71 26.7 27.8 18 - Light Lavender 72 75 28.2 29.4 19 - Lavender 76 79 29.8 31.0 20 - Lime Green 80 83 31.4 32.5 21 - Apricot 84 87 32.9 34.1 22 - Pale Salmon 88 91 34.5 35.7 23 - Dark Salmon 92 95 36.1 37.3 24 - Light Salmon 96 99 37.6 38.8
4 Color wheel
5 Red Red intensity 0100% 0 255 0 100 0 Fade 6 Green Green intensity 0100% 0 255 0 100 0 Fade 7 Blue Blue intensity 0100% 0 255 0 100 0 Fade
25 - White 10.000K 100 103 39.2 40.4 26 - White 8.000K 104 107 40.8 42.0 27 - White 6.000K 108 111 42.4 43.5 28 - White 4.200K 112 115 43.9 45.1 29 - White 3.200K 116 119 45.5 46.7 30 - White 2.700K 120 123 47.1 48.2 No function 124 125 48.6 49.0 Color wheel snap stop 126 129 49.4 50.6 Color wheel snap slow ... fast 130 175 51.0 68.6 Fade Color wheel snap music trigger (1:1 / every trigger) Color wheel snap music trigger (1:4 / every 4th trigger) Color wheel snap music trigger (1:8 / every 8th trigger) Color wheel snap music trigger (1:16 / every 16th trigger) Color wheel fade stop 192 195 75.3 76.5 Color wheel fade slow .. fast 196 239 76.9 93.7 Fade Color wheel fade music trigger (1:1 / every trigger) Color wheel fade music trigger (1:4 / every 4th trigger) Color wheel fade music trigger (1:8 / every 8th trigger) Color wheel fade music trigger (1:16 / every 16th trigger)
176 179 69.0 70.2
180 183 70.6 71.8
184 187 72.2 73.3
188 191 73.7 74.9
240 243 94.1 95.3
244 247 95.7 96.9
248 251 97.3 98.4
252 255 98.8 100.0
Snap
0
Snap
Snap
CL1 / CL1+ User Manual
42
German Light Products® DMX Mode 2: Pattern
DMX Mode 2: Pattern (default mode)
15 DMX Channels
Channel Command
Global
1
intensity
Global intensity 0100% 0 255 0 100 0 Fade
DMX
range Percent
Default
DMX Fade
Shutter closed Music trigger flash 5 9 2.0 3.5 Snap Random pulse slow fast 10 39 3.9 15.3 Fade Random opening pulse slow fast 40 69 15.7 27.1 Fade
Global
2
shutter
Control /
3
Settings
Random closing pulse slow fast 70 99 27.5 38.8 Fade Random double flash slow fast 100 129 39.2 50.6 Fade Random pixel strobe slow fast 130 159 51.0 62.4 Fade Random all strobe slow fast 160 199 62.7 78.0 Fade Strobe sync all pixels 1Hz 10Hz 200 250 78.4 98.0 Fade Open 251 255 98.4 100 Snap No function 0 11 0 4.2 No signal: Blackout (3s hold) 12 15 4.7 5.9 No signal: Hold (3s hold) 16 19 6.3 7.5 No signal: Manual Control (3s hold) 20 23 7.8 9.0 No function 24 39 9.4 15.3 Mic sensitivity: 10 (high, 1s hold) 40 43 15.7 16.9 Mic sensitivity: 09 (1s hold) 44 47 17.3 18.4 Mic sensitivity: 08 (1s hold) 48 51 18.8 20.0 Mic sensitivity: 07 (1s hold) 52 55 20.4 21.6 Mic sensitivity: 06 (1s hold) 56 59 22.0 23.1 Mic sensitivity: 05 (1s hold) 60 63 23.5 24.7 Mic sensitivity: 04 (1s hold) 64 67 25.1 26.3 Mic sensitivity: 03 (1s hold) 68 71 26.7 27.8 Mic sensitivity: 02 (1s hold) 72 75 28.2 29.4 Mic sensitivity: 01 (low, 1s hold) 76 91 29.8 35.7 Emergency light OFF (3s hold) 92 95 36.1 37.3 Emergency light ON (3s hold) 96 99 37.6 38.8 Emergency light Capture RGB values (3s hold) No function 104 223 40.8 87.5 Power mode High (3s hold) 224 227 87.8 89.0 Power mode: Normal (3s hold) 228 231 89.4 90.6 Power mode: Eco (3s hold) 232 235 91.0 92.2 No function 236 239 92.5 93.7 Load default settings (5s hold) 240 243 94.1 95.3 No function 244 255 95.7 100.0
0 4 0 1.6
100 103 39.2 40.4
Snap
255
0 Snap
43 Rev. 20210303-01
DMX Mode 2: Pattern www.glp.de
00 - Open 0 3 0.0 1.2 01 - Red 4 7 1.6 2.7 02 - Green 8 11 3.1 4.3 03 - Blue 12 15 4.7 5.9 04 - Cyan 16 19 6.3 7.5 05 - Magenta 20 23 7.8 9.0 06 - Yellow 24 27 9.4 10.6 07 - Orange 28 31 11.0 12.2 08 - Deep Orange 32 35 12.5 13.7 09 - Pink 36 39 14.1 15.3 10 - Deep Purple 40 43 15.7 16.9 11 - Light Blue 44 47 17.3 18.4 12 - Deep Amber 48 51 18.8 20.0 13 - Light Amber 52 55 20.4 21.6 14 - Deep Golden Amber 56 59 22.0 23.1 15 - Straw 60 63 23.5 24.7 16 - Sunset red 64 67 25.1 26.3 17 - Light Pink 68 71 26.7 27.8 18 - Light Lavender 72 75 28.2 29.4 19 - Lavender 76 79 29.8 31.0 20 - Lime Green 80 83 31.4 32.5 21 - Apricot 84 87 32.9 34.1 22 - Pale Salmon 88 91 34.5 35.7 23 - Dark Salmon 92 95 36.1 37.3 24 - Light Salmon 96 99 37.6 38.8 25 - White 10.000K 100 103 39.2 40.4
4 Color wheel
5 Red Red intensity 0100% 0 255 0 100 0 Fade 6 Green Green intensity 0100% 0 255 0 100 0 Fade 7 Blue Blue intensity 0100% 0 255 0 100 0 Fade
26 - White 8.000K 104 107 40.8 42.0 27 - White 6.000K 108 111 42.4 43.5 28 - White 4.200K 112 115 43.9 45.1 29 - White 3.200K 116 119 45.5 46.7 30 - White 2.700K 120 123 47.1 48.2 No function 124 125 48.6 49.0 Color wheel rotation snap stop 126 129 49.4 50.6 Color wheel rotation snap slow fast Color wheel rotation snap music trigger (1:1 / every trigger) Color wheel rotation snap music trigger (1:4 / every 4th trigger) Color wheel rotation snap music trigger (1:8 / every 8th trigger) Color wheel rotation snap music trigger (1:16 / every 16th trigger) Color wheel rotation fade stop 192 195 75.3 76.5 Color wheel rotation fade slow fast Color wheel rotation fade music trigger (1:1 / every trigger) Color wheel rotation fade music trigger (1:4 / every 4th trigger) Color wheel rotation fade music trigger (1:8 / every 8th trigger) Color wheel rotation fade music trigger (1:16 / every 16th trigger)
130 175 51.0 68.6 Fade
176 179 69.0 70.2
180 183 70.6 71.8
184 187 72.2 73.3
188 191 73.7 74.9
196 239 76.9 93.7 Fade
240 243 94.1 95.3
244 247 95.7 96.9
248 251 97.3 98.4
252 255 98.8 100.0
Snap
0
Snap
Snap
CL1 / CL1+ User Manual
44
German Light Products® DMX Mode 2: Pattern
Pattern
8
9
10
master
Pattern shutter
Pattern selection
Pattern visibility 0 255 0 100 0 Fade
Shutter closed Music trigger flash 5 9 2.0 3.5 Snap Random pulse slow fast 10 39 3.9 15.3 Fade Random opening pulse slow fast 40 69 15.7 27.1 Fade Random closing pulse slow fast 70 99 27.5 38.8 Fade Random double flash slow fast 100 129 39.2 50.6 Fade Random pixel strobe slow fast 130 159 51.0 62.4 Fade Random all strobe slow fast 160 199 62.7 78.0 Fade Strobe sync all pixels 1Hz 10Hz 200 250 78.4 98.0 Fade Open 251 255 98.4 100 Snap Pattern 000 (No Pattern) 0 10 0.0 3.9 Pattern 001 11 15 4.3 5.9 Pattern 002 16 20 6.3 7.8 Pattern 003 21 25 8.2 9.8 Pattern 004 26 30 10.2 11.8 Pattern 005 31 35 12.2 13.7 Pattern 006 36 40 14.1 15.7 Pattern 007 41 45 16.1 17.6 Pattern 008 46 50 18.0 19.6 Pattern 009 51 55 20.0 21.6 Pattern 010 56 60 22.0 23.5 Pattern 011 61 65 23.9 25.5 Pattern 012 66 70 25.9 27.5 Pattern 013 71 75 27.8 29.4 Pattern 014 76 80 29.8 31.4 Pattern 015 81 85 31.8 33.3 Pattern 016 86 90 33.7 35.3 Pattern 017 91 95 35.7 37.3 Pattern 018 96 100 37.6 39.2 Pattern 019 101 105 39.6 41.2 Pattern 020 106 110 41.6 43.1 Pattern 021 111 115 43.5 45.1 Pattern 022 116 120 45.5 47.1 Pattern 023 121 125 47.5 49.0 Pattern 024 126 130 49.4 51.0 Pattern 025 131 135 51.4 52.9 Pattern 026 136 140 53.3 54.9 Pattern 027 141 145 55.3 56.9 Pattern 028 146 150 57.3 58.8 Pattern 029 151 155 59.2 60.8 Pattern 030 156 160 61.2 62.7 Pattern 031 161 165 63.1 64.7 Pattern 032 166 170 65.1 66.7 Pattern 033 171 175 67.1 68.6 Pattern 034 176 180 69.0 70.6 Pattern 035 181 185 71.0 72.5 Pattern 036 186 190 72.9 74.5 Pattern 037 191 195 74.9 76.5 Pattern 038 196 200 76.9 78.4 Pattern 039 201 205 78.8 80.4 Pattern 040 206 210 80.8 82.4
0 4 0 1.6
255
Snap 0
Snap
45 Rev. 20210303-01
DMX Mode 2: Pattern www.glp.de
Random pattern auto change stop 211 212 82.7 83.1 Snap
Pattern
10
selection (contd.)
Pattern
11
step/speed
Random pattern auto change slow fast Random pattern music trigger change (1:8 / every 8th beat) Random pattern music trigger change (1:16 / every 16th beat) Random pattern music trigger change (1:32 / every 32nd beat) Random pattern music trigger change (1:64 / every 64th beat) Pattern step 01 0 1 0.0 0.4 Pattern step 02 2 3 0.8 1.2 Pattern step 03 4 5 1.6 2.0 Pattern step 04 6 7 2.4 2.7 Pattern step 05 8 9 3.1 3.5 Pattern step 06 10 11 3.9 4.3 Pattern step 07 12 13 4.7 5.1 Pattern step 08 14 15 5.5 5.9 Pattern step 09 16 17 6.3 6.7 Pattern step 10 18 19 7.1 7.5 Pattern step 11 20 21 7.8 8.2 Pattern step 12 22 23 8.6 9.0 Pattern step 13 24 25 9.4 9.8 Pattern step 14 26 27 10.2 10.6 Pattern step 15 28 29 11.0 11.4 Pattern step 16 30 31 11.8 12.2 Pattern step 17 32 33 12.5 12.9 Pattern step 18 34 35 13.3 13.7 Pattern step 19 36 37 14.1 14.5 Pattern step 20 38 39 14.9 15.3 Pattern step 21 40 41 15.7 16.1 Pattern step 22 42 43 16.5 16.9 Pattern step 23 44 45 17.3 17.6 Pattern step 24 46 47 18.0 18.4 Pattern step 25 48 49 18.8 19.2 Pattern step 26 50 51 19.6 20.0 Pattern step 27 52 53 20.4 20.8 Pattern step 28 54 55 21.2 21.6 Pattern step 29 56 57 22.0 22.4 Pattern step 30 58 59 22.7 23.1 Pattern step 31 60 61 23.5 23.9 Pattern step 32 62 63 24.3 24.7 Pattern step 33 64 65 25.1 25.5 Pattern step 34 66 67 25.9 26.3 Pattern step 35 68 69 26.7 27.1 Pattern step 36 70 71 27.5 27.8 Pattern step 37 72 73 28.2 28.6 Pattern step 38 74 75 29.0 29.4 Pattern step 39 76 77 29.8 30.2 Pattern step 40 78 79 30.6 31.0
213 247 83.5 96.9 Fade
248 249 97.3 97.6
250 251 98.0 98.4
Snap
252 253 98.8 99.2
254 255 99.6 100.0
Snap 0
0
CL1 / CL1+ User Manual
46
German Light Products® DMX Mode 2: Pattern
Pattern step 41 80 81 31.4 31.8 Pattern step 42 82 83 32.2 32.5 Pattern step 43 84 85 32.9 33.3 Pattern step 44 86 87 33.7 34.1 Pattern step 45 88 89 34.5 34.9 Pattern step 46 90 91 35.3 35.7
Pattern
11
step/speed (contd.)
Pattern color
12
wheel
Pattern step 47 92 93 36.1 36.5 Pattern step 48 94 95 36.9 37.3 No function 96 124 37.6 48.6 Pattern step music trigger (1:1 / step changes every trigger) CW pattern movement fast slow 128 190 50.2 74.5 Pattern movement stop 191 192 74.9 75.3 CCW pattern movement slow fast 193 255 00 - Open 0 3 0.0 1.2 01 - Red 4 7 1.6 2.7 02 - Green 8 11 3.1 4.3 03 - Blue 12 15 4.7 5.9 04 - Cyan 16 19 6.3 7.5 05 - Magenta 20 23 7.8 9.0 06 - Yellow 24 27 9.4 10.6 07 - Orange 28 31 11.0 12.2 08 - Deep Orange 32 35 12.5 13.7 09 - Pink 36 39 14.1 15.3 10 - Deep Purple 40 43 15.7 16.9 11 - Light Blue 44 47 17.3 18.4 12 - Deep Amber 48 51 18.8 20.0 13 - Light Amber 52 55 20.4 21.6 14 - Deep Golden Amber 56 59 22.0 23.1 15 - Straw 60 63 23.5 24.7 16 - Sunset red 64 67 25.1 26.3 17 - Light Pink 68 71 26.7 27.8 18 - Light Lavender 72 75 28.2 29.4 19 - Lavender 76 79 29.8 31.0 20 - Lime Green 80 83 31.4 32.5 21 - Apricot 84 87 32.9 34.1 22 - Pale Salmon 88 91 34.5 35.7 23 - Dark Salmon 92 95 36.1 37.3 24 - Light Salmon 96 99 37.6 38.8 25 - White 10 000 K 100 103 39.2 40.4 26 - White 8000 K 104 107 40.8 42.0 27 - White 6000 K 108 111 42.4 43.5 28 - White 4200 K 112 115 43.9 45.1 29 - White 3200 K 116 119 45.5 46.7 30 - White 2700 K 120 123 47.1 48.2 No function 124 125 48.6 49.0 Color wheel rotation snap stop 126 129 49.4 50.6 Color wheel rotation snap slow fast
125 127 49.0 49.8
75.7 100.0 Fade
130 175 51.0 68.6 Fade
Snap
0
Snap
0
47 Rev. 20210303-01
DMX Mode 2: Pattern www.glp.de
Pattern color
12
wheel (contd.)
Pattern
13
Red Pattern
14
Green Pattern
15
Blue
Color wheel snap music trigger (1:1 / every trigger) Color wheel snap music trigger (1:4 / every 4th trigger) Color wheel snap music trigger (1:8 / every 8th trigger) Color wheel snap music trigger (1:16 / every 16th trigger) Color wheel fade stop 192 195 75.3 76.5 Color wheel fade slow fast 196 239 76.9 93.7 Fade Color wheel fade music trigger (1:1 / every trigger) Color wheel fade music trigger (1:4 / every 4th trigger) Color wheel fade music trigger (1:8 / every 8th trigger) Color wheel fade music trigger (1:16 / every 16th trigger)
Red intensity 0100% 0 255 0 100 0 Fade
Green intensity 0100% 0 255 0 100 0 Fade
Blue intensity 0100% 0 255 0 100 0 Fade
176 179 69.0 70.2
180 183 70.6 71.8
184 187 72.2 73.3
188 191 73.7 74.9
240 243 94.1 95.3
244 247 95.7 96.9
248 251 97.3 98.4
252 255 98.8 100.0
Snap
Snap
CL1 / CL1+ User Manual
48
German Light Products® DMX Mode 3: MultiPix
DMX Mode 3: MultiPix
75 DMX Channels
Channel Command
Global
1
intensity
Global intensity 0100% 0 255 0 100 0 Fade
DMX
range Percent
Default
DMX Fade
Shutter closed Music trigger flash 5 9 2.0 3.5 Snap Random pulse slow fast 10 39 3.9 15.3 Fade Random opening pulse slow fast 40 69 15.7 27.1 Fade
Global
2
shutter
Control /
3
Settings
4 Pixel 01 Red Red intensity 0100% 0 255 0 100 0 Fade
Pixel 01
5
Green
6 Pixel 01 Blue Blue intensity 0100% 0 255 0 100 0 Fade
Random closing pulse slow fast 70 99 27.5 38.8 Fade Random double flash slow fast 100 129 39.2 50.6 Fade Random pixel strobe slow fast 130 159 51.0 62.4 Fade Random all strobe slow fast 160 199 62.7 78.0 Fade Strobe sync all pixels 1Hz 10Hz 200 250 78.4 98.0 Fade Open 251 255 98.4 100 Snap No function 0 11 0 4.2 No signal: Blackout (3s hold) 12 15 4.7 5.9 No signal: Hold (3s hold) 16 19 6.3 7.5 No signal: Manual Control (3s hold) 20 23 7.8 9.0 No function 24 39 9.4 15.3 Mic sensitivity: 10 (high, 1s hold) 40 43 15.7 16.9 Mic sensitivity: 09 (1s hold) 44 47 17.3 18.4 Mic sensitivity: 08 (1s hold) 48 51 18.8 20.0 Mic sensitivity: 07 (1s hold) 52 55 20.4 21.6 Mic sensitivity: 06 (1s hold) 56 59 22.0 23.1 Mic sensitivity: 05 (1s hold) 60 63 23.5 24.7 Mic sensitivity: 04 (1s hold) 64 67 25.1 26.3 Mic sensitivity: 03 (1s hold) 68 71 26.7 27.8 Mic sensitivity: 02 (1s hold) 72 75 28.2 29.4 Mic sensitivity: 01 (low, 1s hold) 76 91 29.8 35.7 Emergency light OFF (3s hold) 92 95 36.1 37.3 Emergency light ON (3s hold) 96 99 37.6 38.8 Emergency light Capture RGB values (3s hold) No function 104 223 40.8 87.5 Power mode High (3s hold) 224 227 87.8 89.0 Power mode: Normal (3s hold) 228 231 89.4 90.6 Power mode: Eco (3s hold) 232 235 91.0 92.2 No function 236 239 92.5 93.7 Load default settings (5s hold) 240 243 94.1 95.3 No function 244 255 95.7 100.0
Green intensity 0100% 0 255 0 100 0 Fade
0 4 0 1.6
255
100 103 39.2 40.4
Snap
0 Snap
… Pixels 02 … 23
73 Pixel 24 Red Red intensity 0100% 0 255 0 100 0 Fade
Pixel 24
74
Green
75 Pixel 24 Blue Blue intensity 0100% 0 255 0 100 0 Fade
Green intensity 0100% 0 255 0 100 0 Fade
49 Rev. 20210303-01
www.glp.de
16. Technical Data
Optical
Light source: 24 x 300 mW RGB LEDs
LED Lifetime: 50 000 hours (to >70% light output)
Control
CL1 and CL1+
Integrated control panel with monochrome OLED display
Infrared remote control
GLP Creative Light smartphone app and iQ.Mesh network
Audio triggering with integrated Sound2Light microphone
CL1+ only
DMX channels: 7, 15 or 75
DMX control modes: 3
Control protocols: Standard DMX (USITT DMX512-A), LumenRadio CRMX TiMo
Electrical
Power Modes: High, Normal, Eco
Power input: 5 VDC
Maximum current draw: 2 A @ 5 VDC
Battery type: Lithium-ion 10 000 mAh
Thermal
Operating temperature range: 0° C (32° F) to 45° C (115° F)
Charging temperature range: 15° C (59° F) to 35° C (95° F)
Cooling: Convection
Overtemperature protection: Automatic thermal cutout
Maximum dissipated heat: 25 BTU/hr.
Installation
Orientation: Any
Location: Dry location only
Min. distance to combustible materials: 20 cm (8 ins.)
Min. distance to illuminated surfaces: 30 cm (1 ft.)
CL1 / CL1+ User Manual
50
German Light Products®
Construction
High-impact flame-resistant thermoplastic, aluminum, steel
Ingress protection: IP20
Kensington system security lock
Connections
Charging: USB-C connector, two charging ports
Firmware update: USB-C or GLP iQ.Mesh network
Included items
1 x GLP CL1 or CL1+ fixture
1 x GLP CL1 Front Screen, white
1 x GLP CL1 Front Screen, clear
1 x GLP Creative Light IR Remote Control Unit
1 x GLP CL1 / CL1+ Quick Start Guide
1 x USB-A to USB-C Charging Cable, 1 m
1 x M6 Eyelet Screw for secondary attachment
Dimensions and weight (identical for CL1 and CL1+)
Diameter: 157 mm (6.2 in)
Depth: 32 mm (1.3 in)
Weight including front-mounted optical accessory: 570 g (20.2 oz.)
Weight, front-mounted optical accessory alone: 35 g (1.3 oz.)
GLP Creative Light smartphone app minimum requirements
Bluetooth version: 4.2 or newer
Android version: 5.1 Lollipop or newer
iOS Version: iOS 8 or newer
Screen resolution: 480 x 850 pixels
RAM: 1 GB
Free storage space: Android 50 MB minimum, iOS 80 MB
51 Rev. 20210303-01
www.glp.de
17. Dimensions
Creative Light 1 (CL1) Creative Light 1 Plus (CL1+)
32
Ø157
150
3
19
62
Dimensions are given in millimeters
CL1 / CL1+ User Manual
52
German Light Products®
CL1 UFO1 (Universal Fixing Object 1)
2
63
1/4″ - 20 UNC
21
6
Ø4
M1
3/8″ - 16 UNC
23
Dimensions are given in millimeters
53 Rev. 20210303-01
Loading...