GLO-TOOB Lithium & IR User Manual

TM

Pat.No.US7218241

User Guide

11

MODES

LITHIUM

875nm

&

CAUTION: Infrared versions of this
model may only be seen with night
imaging equipment and NOT the
naked eye.

www.glo-toob.com

KEY FEATURES

950nm

Detachable Lanyard

High intensity waterproof light source

Push Button Cap

BATTERY TYPE
CR123A 3V

Twist Waterproof Cap

Waterproof to 3,500 meters
(11,500 feet)

ONLY WHEN TWIST CAP IS USED

*

*

11 Modes to choose from

Powered by 10 Year Shelf
Life Lithium Battery

Protector Cover

CR123A Lithium Battery

Virtually indestructible

SPECIFICATIONS

Battery life 24-100 hours
Battery life 20-80 hours (IR)
(dependent on mode
selection)

Dimensions ................................ 80mm x 24mm (3.15in x 0.95in)

Durability.............................................................. High-impact resistant

GLO-TOOB Body

The GLO-TOOB Lithium & IR allows you to select one of its 11 modes as your LOCKED mode. This LOCKED mode is the
mode the unit will activate when you turn it ON. In order to select or modify your LOCKED mode, follow these simple steps.

STEP 1: Switch the GLO-TOOB Lithium ON - count 5 seconds and then switch
the unit OFF and then ON again (this will activate the programming mode).
STEP 2: Now, by repeatedly switching the unit ON and OFF you will cycle through
the 11 different pre-programmed modes.
STEP 3: In order to select and store a new LOCKED mode, leave the unit on that
particular mode for 4 seconds or longer.

Working Temperature ................................ -20 C to +80 C (-4 F to 176 F )

Buoyancy ............................................................................................... Negative

Colors available ...................................... Red, Amber, Blue, Green, White & Infra-Red

SELECTING A MODE

Light Source ........................... High Bright LED’s

LED Life ....................................... Approx. 100,000 hrs

Battery Life .............. 24 to 100 hours (Dependent on mode)

EQUAL FLASH
BEACON STROBE
FAST STROBE
SLOW STROBE
SOS
PULSE
HALF FLASH
BOUNCE
RAMP UP
100% Constant on
25% Constant on

Weight .................. 62g (2.18 oz)

Shape ................................. Cylindrical

Viewing Angle...................................... 360

0 0 0 0

875nm

& 950nm

0

When you now switch the unit OFF and ON again, it will activate your new LOCKED mode. Repeat STEPS 1-3 if you would
like to change your LOCKED mode again.

CAP SPECIFICATIONS

Thread
Protector Cover

Aircraft grade aluminum

with hard coat anodizing

Strength

Attachment type

Switch type

Waterproof

Working temperature

Seal type

Push Button Splashproof
Lanyard Cap

Yes

Low impact

Detachable Lanyard & Clip

Push button

Splashproof

-20 C to +80 C (-4 F to 176 F ) -20 C to +80 C (-4 F to 176 F )

1 x Nitrile washer

Twist On/Off Waterproof Cap

Yes

Low impact

Large Stainless Steel split-ring

Twist ON / OFF

3,500 meters (11,500 feet)

1 x Nitrile washer

Push Button Splashproof Lanyard Cap Twist On/Off Waterproof Cap

The Push Button Splashproof Cap is
designed for above water use only.
Simply depress the rubber cap to
turn ON or OFF to cycle through
the multi-mode functions. This cap
is equipped with a STRONG 40cm(15.7”)
DETACHABLE LANYARD.

The Twist ON/OFF Waterproof Cap allows the
GLO-TOOB to be switched ON or OFF under­water at any depth. CAUTION: TAKE CARE

TO ONLY TURN THE PLASTIC CAP WHILE
UNDERWATER SO AS NOT TO LOOSEN
THE CAP AND CAUSE ACCIDENTAL
FLOODING. This cap is equipped with an

EXTRA STRENGTH STAINLESS STEEL
ATTACHMENT RING.

When the cap is not in use, use the protector cover to ensure
no water comes in contact with the conductive threads.

Care and Maintenance

In order to prolong the life of your GLO-TOOB, it is recommended that preventive maintenance is
performed on a periodic basis as follows:

1. Exposure to Saltwater

After saltwater exposure it is highly recommended that the GLO-TOOB is rinsed in fresh water and
then dried before opening. This will reduce the possibility of corrosion and extend the life of your
GLO-TOOB.

2. Contact surfaces

All GLO-TOOB caps have conductive aluminum threads to hold the caps in place as well as to
conduct power. Should the threads come into contact with water, an aluminum oxide layer will be
formed around the threads possibly rendering the contact area faulty. For this reason please make
sure the threads stay dry and clean. Use the universal protector cover to keep threads dry and clean
when not in use around wet environments.

3. Washer (seal)
The washer on the inside of the caps must be checked each time before the GLO-TOOB is
submersed in water. If the washer is cracked or cut, replace the washer immediately. Also check for
general cleanliness of the washer to ensure that particles do not affect the watertight seal.

4. Battery

Leaking batteries can corrode the inside of your GLO-TOOB. It is therefore recommended that
you open your GLO-TOOB once a month and check the battery for signs of leakage and / or
corrosion. It is also recommended that you remove the batteries from your GLO-TOOB and store
them separately if you use your GLO-TOOB infrequently.

LIMITED LIFETIME WARRANTY

The manufactures of GLO-TOOB warrants each GLO-TOOB to be free from defects in material and workmanship.
Under this warranty the manufactures of GLO-TOOB obligation is limited to replacing or repairing any GLO­TOOB returned to us and found to be defective in either material or workmanship.
This warranty excludes the following: 1. Battery Leakage (determine the brand of the battery and follow
that battery manufacture’s instructions on how to make a damage claim). 2. LED Burnout. 3. Failure of or
damage to GLO-TOOB due to misuse and/or lack of maintenance. 4. Accidental flooding of the GLO­TOOB by exposing the battery chamber to moisture/water.

For WARRANTY INFORMATION or REPAIR INSTRUCTIONS, please visit out our website at:

www.glo-toob.com