Glory Horse WSR1801 BE322 User Manual
FCC ID:2ABL5WSR1801-BE322
Shipped without battery
B
A
D
C E F
N
M
PRESET
USB 5V
VOLUME
L
K
A-USB power outlet
B-MP3 player storage
G
C-FM Antenna
H
D-Power on/off
E-Mode selector button
F-Digital display
G-Button for search radio stations
(upwards)
J
H-Button for search radio stations
(downwards)
J-Bluetooth
K-Auxiliary jack
L-Preset
M-Button to decrease volume
N-Button to increase volume
Insert/Remove battery pack
O-Latches
P-Grooves
O
P
Insert battery pack:
Slide in the battery pack until it engages.
Remove battery pack:
Press the battery pack release(O) button
and remove the battery pack.
R S T U
Q
PRESET
VOLUME
USB 5V
Q-Radio station memory number.
R-Bluetooth: activated
S-Bluetooth: radio is connected to a different
Bluetooth device
T-USB power outlet
U-Display of battery pack level
D E F
N
M
L
VOLUME
USB 5V
PRESET
G
H
J
1.1 Switching On and off
To switch on: Press button(D).
To switch off: Press button(D) again.
1.2 Adjusting the volume
Increase volume: Press “VOL+” button(N).
Decrease volume: Press “VOL-” button(M).
1.3 Mode selector button
To change between FM, AM, BT, AUX, press the “MODE”
button(E) several times.
1.4 Operation BAUER radio FM / AM
.Searching for radio stations
Press “I<< ” button(H) or “>>I button(G) ” to change the
frequency, The current frequency is shown on the display(F).
To search the next radio station with high signal strength,
press“I<< ” button(H) or “>>I button(G) ” and keep pressed
briefly. The current frequency is shown on the display(F).
.Store set radio station
Press the “PRESET” button(L) for a long time. The selected
memory number blinks on the display(F).
Rem.: The radio station can only be stored as long as the
number is blinking.
Set the desired memory number by pressing button “I<< ”
button(H) or “>>I button(G) ”
Press the “PRESET” button(L) briefly(store radio station)
.Listening to stored radio stations
Press the “PRESET” button(L) briefly until the desired stored
radio station is shown on the display(F) and played.
1.5 Connecting to Bluetooth
SCAN
USB 5V
VOLUME
.To change to BT(Bluetooth), press the“MODE”
button (E)several times, until BT shows on the
display.
.Activate Bluetooth on your smart phone(or
USB 5V
VOLUME
another mobile device such as a tablet).
.If your smart phone has detected the BT, it will
be shown with the device name “BAUER”.
.On your smart phone establish the connection
to the device. The successful connection is shown
on the display(F) by pressing the symbol(S).
.When your smart phone is connected the BT, the
user press the button “I<< ” button(H) or “>>I
button(G) ” to operate the music of your smart
“ ”
phone.
.Press briefly the button “ ” to start and pause
the music. Press and hold the button “ ” more
than 2 seconds to disconnect and waiting for the
other BT device to connect.
1.6 Connecting an Auxiliary Device
USB 5V
VOLUME
.Connect an MP3 player, CD player, or other audio
device directly to the “Bauer radio” using the stereo
auxiliary jack.
1.7 USB Power Outlet
A
.
This outlet can be used to charge a smart phone,
power an MP3 player and any other device that uses less than 2.1A of
DC electrical current.
Note
Any device that used more than 2.1 A of DC electrical current will
trip a self-resetting overload and
disable the output.
V
K
V-Auxiliary cable
FCC caution
Federal Communication Commission (FCC) Radiation Exposure Statement
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1)this device may not cause harmful interference, and
(2)this device must accept any interference received, including interference that may
cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications or changes to this equipment. Such modifications or
changes could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
‐
Reorient or relocate the receiving antenna.
‐
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
‐
receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
Loading...