Globe GG48TG, GG48G User Manual

Serial #:

GG36TG

Conversion Kit Instructions for the

Globe Gas Countertop Griddle

Models:

Thermostatically Controlled: GG24TG, GG36TG, GG48TG,

For Installation and Service on Your Gas Griddle:

1. Visit our website at www.globefoodequip.com

2. Or call the Globe Service Department at 937-299-8625 and ask for contact
information for your local service company.

Visit our website for information on additional products available from Globe.

www.globefoodequip.com

Slicers, Mixers, Countertop Cooking Equipment, Meat Choppers & Scales

- IMPORTANT NOTICE -

Conversion instructions are for conversion of the THERMOSTAT GRIDDLE. The instructions provided in this

kit are for the conversion of Natural Gas to L.P. Gas and refer to the conversion of the unit and kit provided. An

authorized licensed technician must be called to perform the complete conversion of the unit. Failure to properly

convert this unit can result in serious injury, property damage or death, and will void the warranty.

O:\Service\Public\service bulletins\999239 Gas Conversion Thermostat Griddle Rev. C

Pg 1 of 4

Gas Griddle (Thermostat Controlled)
Conversion Kit Instructions

Do not attempt gas conversion by yourself. Gas conversion of your unit is to be

made by a certifi ed/licensed technician. Locate an authorized Globe servicer at

www.globefoodequip.com

IMPORTANT NOTE for SERVICERS: At least two people are required for this conversion. (2) 2'' x 4''
pieces of wood at least 3 feet long are also needed for proper positioning of equipment.

TEAM LIFT! DO NOT ATTEMPT TO LIFT OR POSITION THE GRIDDLE FOR SERVICE ALONE.

At least one other person is required to aid in lifting and spotting the equipment at all times.

CONVERSION

Instructions are for conversion from Natural Gas to Propane (L.P.) on all models. The conversion should be done
before connecting the unit to the gas supply. Units are shipped from the factory equipped for use on natural gas.
Parts necessary for L.P. (liquid propane) are provided with the unit. Turn off the main gas supply before doing

any maintenance. (Use only factory supplied regulator!)

1. Remove the knobs and
front panel to help with
access. Loosen and remove
the 4 screws on the front of
the control panel, Remove
the panel from the front of
the griddle. Also, remove the
crumb tray from underneath
the griddle and set it off to the
side.

2. Remove the back and underneath panels
of the griddle revealing the innards of the
griddle. Make sure the griddle is SECURE while
standing in place for the adjustments.
Safety First.

3. Remove the main burner tube,
loosen the gas supply tube at the gas
control unit end of the supply tube
to allow the tube to be moved easily
without bending.

5. Determine the correct injector size for the corresponding
gas from the rating label.

6. Replace with the correct size injectors.

Refer to ‘Gas Specifi cations Table’ for

injector sizes.

7. Before installing the included
convertible regulator, unscrew
the octagon cap. You can read
(NAT) on the plastic insert
attached to the head of the

cap; fl ip it over and snap back

in place.

Convertible

regulator with

octagon cap.

Unscrew from

regulator.

Pilot Burners

8. Remove the pilot gas supply pipe. First
remove the two screws on the mounting
bracket. Then loosen both ends of the
pilot supply pipe and withdraw the pilot
injector from inside the pilot burner.

9. Determine the correct injector size for
the corresponding gas from the rating
label. Replace with the correct size
injectors.

10. Reconnect the supply tube
to the base of the pilot burner
and tighten the gas supply
tube at the gas supply end.
(Repeat instructions for each
burner.)

11. Refi t the front control panel

and tighten the 4 screws on
the front to secure the panel

in place. Refi t the pack and

underneath panels as well.

Pilot

Injector

Gas

Supply

Pipe

4. Unscrew and remove the injector
(½'' A/F) from the main burner end
clamp.

Main
Injector

(Gas Specifi cations Table on page 3)

Pg 2 of 4

Rev. C O:\Service\Public\service bulletins\999239 Gas Conversion Thermostat Griddle

12. Refi t the control knobs to the

front control panel. The

control knobs are a push fi t

onto the shafts of the gas
control valves.