Global Telecom GLC130P Users manual
GWG130WV Home Gateway
User Manual
Page 1
PLEASE READ THESE SAFETY PRECAUTIONS!
RF Energy Health Hazard
The radio equipment described in this guide uses radio frequency transmitters. Although
the power level is low, the concentrated energy from a directional antenna may pose a
health hazard. Do not allow people to come in close proximity to the front of the antenna
while the transmitter is operating.
Protection from Lightning
Before connecting this instrument to the power line, make sure that the voltage of the power source
matches the requirements of the instrument. The unit must be standards.
Disposal and Recycling Information
Pursuant to the WEEE EU Directive electronic and electrical waste must not be disposed of
with unsorted waste. Please contact your local recycling authority for disposal of this
product.
Reduction of Hazardous Substances
This CPE is compliant with the EU Registration, Evaluation, Authorization and Restriction
of Chemicals (REACH) Regulation (Regulation No 1907/2006/EC of the European
Parliament and of the Council) and the EU Restriction of Hazardous Substances (RoHS)
Directive (Directive 2002/95/EC of the European Parliament and of the Council)
.
FCC Notice, USA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Page 2
Table of contents
1. OVERVIEW ............................................................................................................................................... 4
1.1 USER INTERFACE SPECIFICATION ............................................................................................................ 4
1.2 WI-FI INTERFACE(IDU) .......................................................................................................................... 4
2. GETTING STARTED ................................................................................................................................ 4
2.1 PACKING LIST AND CPE UNIT ................................................................................................................. 4
2.2 INSTALLING THE EQUIPMENT .................................................................................................................. 5
Device logic connection ......................................................................................................................... 5
LED Display .......................................................................................................................................... 6
3. MANAGING CPE DEVICE ..................................................................................................................... 6
3.1 WEB LOGIN—172.16.1.1 ...................................................................................................................... 6
3.2 SYSTEM STATU S DISPLAY ....................................................................................................................... 6
3.3 NETWORK CONFIGURATION .................................................................................................................... 7
Modify MTU Size ................................................................................................................................... 7
3.4 WI-FI CONFIGURATION-MODIFY SSID/SECURITY .................................................................................. 8
WPS setting ............................................................................................................................................ 9
3.5 SERVICE CONFIGURATION-DMZ SETTING .............................................................................................. 9
3.6 VOIP CONFIGURATION-SIP ACCOUNT SETTING..................................................................................... 10
3.7 SYSTEM MAINTENANCE ........................................................................................................................ 11
Telnet Enable all and modify password ............................................................................................... 11
TR069 Configuration ........................................................................................................................... 11
Firmware Upgrade over HTTP ............................................................................................................ 13
Load Factory Default ........................................................................................................................... 13
4. HARDWARE RESET .............................................................................................................................. 14
5. FAQ AND TROUBLESHOOTING ........................................................................................................ 14
Page 3
1. Overview
AM4000M is an indoor multiservice gateway unit (IDU) that
supports advanced networking, VoIP gateway and WLAN AP
functionalities. It enables wide service coverage and provides
high data throughput and networking features to customers
who needs easy broadband access, low cost VoIP service and
Wi-Fi connectivity.
1.1 User Interface Specification
Model Description & User Interface
- 1 RJ45 10/100M ETH (PoE),2 RJ45 10/100M ETH,1 RJ11/FXS Line
- Power, NET, Wi-Fi, LAN1-2, LINE, WPS
AM4000M
1.2 Wi-Fi Interface(IDU)
Radio Access 802.11b/g/n (300 Mbps)
- 24V/1.0A DC
- Dimensions: 135 mm (L) × 105 mm (W) × 30mm (D)
- Weight: < 300g
Output Power
Antenna 3dBi built-in antenna
Security 64/128 bit WEP, WPA/WPA2
15 1dBm
2. Getting Started
2.1 Packing list and CPE Unit
Upon receiving the product, please unpack the product package carefully. Each product is shipped
with the following items:
Table 2-1 Packing List
Products Quantity
IDU unit 1
24V DC Power adapter 1
PC Ethernet Cable 1
If you find any of the items is missing, please contact our local distributor immediately.
Page 4
CPE Unit:
Unpacking the Equipment Table 2-1 lists all the standard parts that are supplied in your LTE CPE Unit
Installation Package. Please take the time to unpack the package and check its contents against this list.
2.2 Installing the Equipment
Device logic connection
AM4000M is user-friendly and easy to setup. To power on the IDU device, the IDU must uses a 24V
DC power supply adapter. The power adapters can operate in 90-250V AC range and therefore can be
used in different countries. Once the IDU device is powered up, the user should wait for about 2
minutes before the device becomes operational.
To connect PC, LAN switch or other type of IP device to the product, the user should use standard
CAT5 Ethernet cable and connect to the appropriate LAN port of the IDU. Once connect the CPE
LAN LED indicator should come on.
To use the phone service, user can simply plug the phone line to the CPE RJ11 port in the back. If the
line is not registered or configured, a fast busy tone will be provided and the corresponding LINE
LED light will be off.
Page 5
Loading...